[PATCH v2 11/16] gpio: add support for the sl28cpld GPIO controller

[Michael Walle]

This adds support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.

Signed-off-by: Michael Walle <michael@xxxxxxxx>
---
 drivers/gpio/Kconfig         |  11 +++
 drivers/gpio/Makefile        |   1 +
 drivers/gpio/gpio-sl28cpld.c | 186 +++++++++++++++++++++++++++++++++++
 3 files changed, 198 insertions(+)
 create mode 100644 drivers/gpio/gpio-sl28cpld.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index a8e148f4b2e0..d6d54cb9558e 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1215,6 +1215,17 @@ config GPIO_RC5T583
 	  This driver provides the support for driving/reading the gpio pins
 	  of RC5T583 device through standard gpio library.
 
+config GPIO_SL28CPLD
+	tristate "Kontron sl28 GPIO"
+	depends on MFD_SL28CPLD
+	select GPIO_REGMAP
+	select GPIOLIB_IRQCHIP
+	help
+	  This enables support for the GPIOs found on the Kontron sl28 CPLD.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called gpio-sl28cpld.
+
 config GPIO_STMPE
 	bool "STMPE GPIOs"
 	depends on MFD_STMPE
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 93e139fdfa57..f50ccf13f5eb 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -129,6 +129,7 @@ obj-$(CONFIG_GPIO_SCH311X)		+= gpio-sch311x.o
 obj-$(CONFIG_GPIO_SCH)			+= gpio-sch.o
 obj-$(CONFIG_GPIO_SIFIVE)		+= gpio-sifive.o
 obj-$(CONFIG_GPIO_SIOX)			+= gpio-siox.o
+obj-$(CONFIG_GPIO_SL28CPLD)		+= gpio-sl28cpld.o
 obj-$(CONFIG_GPIO_SODAVILLE)		+= gpio-sodaville.o
 obj-$(CONFIG_GPIO_SPEAR_SPICS)		+= gpio-spear-spics.o
 obj-$(CONFIG_GPIO_SPRD)			+= gpio-sprd.o
diff --git a/drivers/gpio/gpio-sl28cpld.c b/drivers/gpio/gpio-sl28cpld.c
new file mode 100644
index 000000000000..1d199517e2e0
--- /dev/null
+++ b/drivers/gpio/gpio-sl28cpld.c
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * sl28cpld GPIO driver.
+ *
+ * Copyright 2019 Michael Walle <michael@xxxxxxxx>
+ */
+
+#include <linux/device.h>
+#include <linux/gpio-regmap.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* GPIO flavor */
+#define GPIO_REG_DIR	0x00
+#define GPIO_REG_OUT	0x01
+#define GPIO_REG_IN	0x02
+#define GPIO_REG_IE	0x03
+#define GPIO_REG_IP	0x04
+
+/* input-only flavor */
+#define GPI_REG_IN	0x00
+
+/* output-only flavor */
+#define GPO_REG_OUT	0x00
+
+enum sl28cpld_gpio_type {
+	SL28CPLD_GPIO = 1,
+	SL28CPLD_GPI,
+	SL28CPLD_GPO,
+};
+
+struct sl28cpld_gpio {
+	struct gpio_regmap gpio_chip;
+	struct regmap_irq_chip irq_chip;
+	struct regmap_irq_chip_data *irq_data;
+};
+
+static const struct regmap_irq sl28cpld_gpio_irqs[] = {
+	REGMAP_IRQ_REG_LINE(0, 8),
+	REGMAP_IRQ_REG_LINE(1, 8),
+	REGMAP_IRQ_REG_LINE(2, 8),
+	REGMAP_IRQ_REG_LINE(3, 8),
+	REGMAP_IRQ_REG_LINE(4, 8),
+	REGMAP_IRQ_REG_LINE(5, 8),
+	REGMAP_IRQ_REG_LINE(6, 8),
+	REGMAP_IRQ_REG_LINE(7, 8),
+};
+
+static int sl28cpld_gpio_irq_init(struct device *dev,
+				   struct sl28cpld_gpio *gpio,
+				   struct regmap *regmap, unsigned int base,
+				   int irq)
+{
+	struct regmap_irq_chip *irq_chip = &gpio->irq_chip;
+
+	irq_chip->name = "sl28cpld-gpio-irq",
+	irq_chip->irqs = sl28cpld_gpio_irqs;
+	irq_chip->num_irqs = ARRAY_SIZE(sl28cpld_gpio_irqs);
+	irq_chip->num_regs = 1;
+	irq_chip->status_base = base + GPIO_REG_IP;
+	irq_chip->mask_base = base + GPIO_REG_IE;
+	irq_chip->mask_invert = true,
+	irq_chip->ack_base = base + GPIO_REG_IP;
+
+	return devm_regmap_add_irq_chip_np(dev, dev_of_node(dev), regmap,
+					   irq, IRQF_SHARED | IRQF_ONESHOT, 0,
+					   irq_chip, &gpio->irq_data);
+}
+
+static int sl28cpld_gpio_probe(struct platform_device *pdev)
+{
+	const struct platform_device_id *dev_id;
+	enum sl28cpld_gpio_type type;
+	struct sl28cpld_gpio *gpio;
+	struct gpio_regmap *gpio_chip;
+	struct regmap *regmap;
+	struct resource *res;
+	bool irq_support = false;
+	unsigned int base;
+	int ret;
+	int irq;
+
+	if (!pdev->dev.parent)
+		return -ENODEV;
+
+	dev_id = platform_get_device_id(pdev);
+	if (dev_id)
+		type = dev_id->driver_data;
+	else
+		type = (uintptr_t)of_device_get_match_data(&pdev->dev);
+	if (!type)
+		return -ENODEV;
+
+	gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
+	if (!gpio)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_REG, 0);
+	if (!res)
+		return -EINVAL;
+	base = res->start;
+
+	regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!regmap)
+		return -ENODEV;
+
+	gpio_chip = &gpio->gpio_chip;
+	gpio_chip->regmap = regmap;
+	gpio_chip->parent = &pdev->dev;
+	gpio_chip->ngpio = 8;
+
+	switch (type) {
+	case SL28CPLD_GPIO:
+		gpio_chip->reg_dat_base = GPIO_REGMAP_ADDR(base + GPIO_REG_IN);
+		gpio_chip->reg_set_base =
+				GPIO_REGMAP_ADDR(base + GPIO_REG_OUT);
+		gpio_chip->reg_dir_out_base =
+				GPIO_REGMAP_ADDR(base + GPIO_REG_DIR);
+		irq_support = true;
+		break;
+	case SL28CPLD_GPO:
+		gpio_chip->reg_set_base = GPIO_REGMAP_ADDR(base + GPO_REG_OUT);
+		break;
+	case SL28CPLD_GPI:
+		gpio_chip->reg_dat_base = GPIO_REGMAP_ADDR(base + GPI_REG_IN);
+		break;
+	default:
+		dev_err(&pdev->dev, "unknown type %d\n", type);
+		return -ENODEV;
+	}
+
+	if (irq_support &&
+	    device_property_read_bool(&pdev->dev, "interrupt-controller")) {
+		irq = platform_get_irq(pdev, 0);
+		if (irq < 0)
+			return irq;
+
+		ret = sl28cpld_gpio_irq_init(&pdev->dev, gpio, regmap,
+					     base, irq);
+		if (ret)
+			return ret;
+
+		gpio_chip->irq_domain = regmap_irq_get_domain(gpio->irq_data);
+		dev_info(&pdev->dev, "registered IRQ %d\n", irq);
+	}
+
+	return devm_gpio_regmap_register(&pdev->dev, gpio_chip);
+}
+
+static const struct of_device_id sl28cpld_gpio_of_match[] = {
+	{ .compatible = "kontron,sl28cpld-gpio",
+	  .data = (void *)SL28CPLD_GPIO },
+	{ .compatible = "kontron,sl28cpld-gpi",
+	  .data = (void *)SL28CPLD_GPI },
+	{ .compatible = "kontron,sl28cpld-gpo",
+	  .data = (void *)SL28CPLD_GPO },
+	{},
+};
+MODULE_DEVICE_TABLE(of, sl28cpld_gpio_of_match);
+
+static const struct platform_device_id sl28cpld_gpio_id_table[] = {
+	{ "sl28cpld-gpio", SL28CPLD_GPIO },
+	{ "sl28cpld-gpi", SL28CPLD_GPI },
+	{ "sl28cpld-gpo", SL28CPLD_GPO },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, sl28cpld_gpio_id_table);
+
+static struct platform_driver sl28cpld_gpio_driver = {
+	.probe = sl28cpld_gpio_probe,
+	.id_table = sl28cpld_gpio_id_table,
+	.driver = {
+		.name = KBUILD_MODNAME,
+		.of_match_table = sl28cpld_gpio_of_match,
+	},
+};
+module_platform_driver(sl28cpld_gpio_driver);
+
+MODULE_DESCRIPTION("sl28cpld GPIO Driver");
+MODULE_AUTHOR("Michael Walle <michael@xxxxxxxx>");
+MODULE_LICENSE("GPL");
-- 
2.20.1