Re: [PATCH V4 3/4] backlight: qcom-wled: Add WLED5 bindings

[kgunda]

On 2020-03-31 23:26, Rob Herring wrote:
> On Mon, Mar 23, 2020 at 11:16:57PM +0530, Kiran Gunda wrote:
> > Add WLED5 specific bindings.
>
> More of the same comments here...
>
> > Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
> > Signed-off-by: Subbaraman Narayanamurthy <subbaram@xxxxxxxxxxxxxx>
> > ---
> >  .../bindings/leds/backlight/qcom-wled.yaml         | 39 
> > ++++++++++++++++++++++
> >  1 file changed, 39 insertions(+)
> >
> > diff --git 
> > a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml 
> > b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
> > index 8a388bf..159115f 100644
> > --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
> > +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
> > @@ -20,6 +20,7 @@ properties:
> >         - qcom,pm8941-wled
> >         - qcom,pmi8998-wled
> >         - qcom,pm660l-wled
> > +       - qcom,pm8150l-wled
> >
> >    reg:
> >      maxItems: 1
> > @@ -28,10 +29,23 @@ properties:
> >      maxItems: 1
> >      description:
> >        brightness value on boot, value from 0-4095.
> > +      For pm8150l this value vary from 0-4095 or 0-32767
> > +      depending on the brightness control mode. If CABC is
> > +      enabled 0-4095 range is used.
>
> Constraints.
Will address it in next post.
> >      allOf:
> >        - $ref: /schemas/types.yaml#/definitions/uint32
> >          default: 2048
> >
> > +  max-brightness:
> > +    maxItems: 1
> > +    description:
> > +      Maximum brightness level. Allowed values are,
> > +      for pmi8998 it is  0-4095.
> > +      For pm8150l, this can be either 4095 or 32767.
>
> Constraints!
Will address it in next post.
> > +      If CABC is enabled, this is capped to 4095.
> > +    allOf:
> > +      - $ref: /schemas/types.yaml#/definitions/uint32
>
> Standard property. Assume it has a type definition.'
Will address it in next post.
> > +
> >    label:
> >      maxItems: 1
> >      description:
> > @@ -124,6 +138,31 @@ properties:
> >        value for PM8941 from 1 to 3. Default 2
> >        For PMI8998 from 1 to 4.
> >
> > +  qcom,modulator-sel:
> > +    maxItems: 1
> > +    allOf:
> > +      - $ref: /schemas/types.yaml#/definitions/uint32
> > +    description:
> > +      Selects the modulator used for brightness modulation.
> > +      Allowed values are,
> > +               0 - Modulator A
> > +               1 - Modulator B
> > +      If not specified, then modulator A will be used by default.
> > +      This property is applicable only to WLED5 peripheral.
> > +
> > +  qcom,cabc-sel:
> > +    maxItems: 1
> > +    allOf:
> > +      - $ref: /schemas/types.yaml#/definitions/uint32
> > +    description:
> > +      Selects the CABC pin signal used for brightness modulation.
> > +      Allowed values are,
> > +              0 - CABC disabled
> > +              1 - CABC 1
> > +              2 - CABC 2
> > +              3 - External signal (e.g. LPG) is used for dimming
> > +      This property is applicable only to WLED5 peripheral.
> > +
> >    interrupts:
> >      maxItems: 2
> >      description:
> > --
> > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora 
> > Forum,
> >  a Linux Foundation Collaborative Project