Re: [PATCH 4/5] ARM: dts: sam9x60: add rtt

[Alexandre Belloni]

On 14/04/2020 08:42:08+0000, Claudiu.Beznea@xxxxxxxxxxxxx wrote:
> > Why would one use the RTT while the RTC is far superior?
> 
> I didn't enabled this for a particular use case, but: couldn't this be used
> by some user that wants to generate multiple alarms? from multiple RTCs?
> 

I very much doubt that as Linux is able to properly multiplex alarms and
basically, the only one we are interested in is actually wakeup.

> Moreover, this IP's counter has the possibility of being clocked at 1Hz.
> Couldn't this minimize the power consumption while being in a power saving
> mode?
> 

And that 1Hz clock is coming from the RTC so using the RTC is
definitively consuming less power.

> > 
> >>>
> >>> In any case, this diff should be merge with the other at91-sam9x60ek.dts
> >>> change instead of being with the dtsi change.
> >>
> >> The changes in this patch are related to enabling the RTT. The other dts
> >> change is related to enabling gpbr. The RTT uses that enabled gpbr -> one
> >> change per patch.
> >>
> >> If you still want to merge then, I'll do it, but then it becomes mixed.
> >>
> > 
> > This patch is already mixing add the gpbr in sam9x60ek and add the node
> > in sam9x60.dtsi which is worse.
> 
> This patch is like this:
> 
> diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts
> b/arch/arm/boot/dts/at91-sam9x60ek.dts
> index ab3d2d9a420a..4020e79a958e 100644
> --- a/arch/arm/boot/dts/at91-sam9x60ek.dts
> +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
> @@ -617,6 +617,11 @@
>  	};
>  };
> 
> +&rtt {
> +	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
> +	status = "okay";
> +};
> +
>  &shutdown_controller {
>  	atmel,shdwc-debouncer = <976>;
>  	status = "okay";
> diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
> index 326b39328b58..e1d8e3a4cb0b 100644
> --- a/arch/arm/boot/dts/sam9x60.dtsi
> +++ b/arch/arm/boot/dts/sam9x60.dtsi
> @@ -661,6 +661,13 @@
>  				status = "disabled";
>  			};
> 
> +			rtt: rtt@fffffe20 {
> +				compatible = "microchip,sam9x60-rtt";
> +				reg = <0xfffffe20 0x20>;
> +				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
> +				clocks = <&clk32k 0>;
> +			};
> +
> 
> It doesn't adds the GPBR in sam9x60ek, it adds rtt in sam9x60ek which uses
> GPBR.
> 
> > 
> > Just have one patch adding the rtt node to the sam9x60.dtsi and then a
> > patch adding the RTT to sam9x60ek.
> 
> Ok, I understand this.
> 
> > Because the RTT uses the gpbr, it is
> > a good time to add enable the gpbr, this is a single functionnal change.
> > 
> > Let's say that for some reason, the RTT patch on sam9x60ek has to be
> > reverted, then the RTT node is still defined which is good for all the
> > other eventual users.
> 
> RTT node would still be defined but GPBR node will not be enabled.
> 
> If RTT patch contains this change that I understand you want me to merge here:
> 
> +&gpbr {
> +	status = "okay";
> +};
> +
> 
> then, theoretically, some other IPs using the GPBR (RTC have the
> possibility of doing this), may be broken by reverting the RTT patch that
> includes the GPBR enabling patch.
> 

But this is very unlikely to happen because this would be limited to a
single board device tree instead of impact every sam9x60 based boards.


-- 
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com