[PATCH 5.6 12/71] net: dsa: mt7530: move mt7623 settings out off the mt7530
From: Greg Kroah-Hartman
Date: Mon Apr 20 2020 - 08:56:50 EST
From: "Renéan Dorst" <opensource@xxxxxxxxxx>
[ Upstream commit 84d2f7b708c374a15a2abe092a74e0e47d018286 ]
Moving mt7623 logic out off mt7530, is required to make hardware setting
consistent after we introduce phylink to mtk driver.
Fixes: ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
Reviewed-by: Sean Wang <sean.wang@xxxxxxxxxxxx>
Tested-by: Sean Wang <sean.wang@xxxxxxxxxxxx>
Signed-off-by: Renà van Dorst <opensource@xxxxxxxxxx>
Tested-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
Signed-off-by: David S. Miller <davem@xxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
drivers/net/dsa/mt7530.c | 85 -----------------------------------------------
drivers/net/dsa/mt7530.h | 10 -----
2 files changed, 95 deletions(-)
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -67,58 +67,6 @@ static const struct mt7530_mib_desc mt75
};
static int
-mt7623_trgmii_write(struct mt7530_priv *priv, u32 reg, u32 val)
-{
- int ret;
-
- ret = regmap_write(priv->ethernet, TRGMII_BASE(reg), val);
- if (ret < 0)
- dev_err(priv->dev,
- "failed to priv write register\n");
- return ret;
-}
-
-static u32
-mt7623_trgmii_read(struct mt7530_priv *priv, u32 reg)
-{
- int ret;
- u32 val;
-
- ret = regmap_read(priv->ethernet, TRGMII_BASE(reg), &val);
- if (ret < 0) {
- dev_err(priv->dev,
- "failed to priv read register\n");
- return ret;
- }
-
- return val;
-}
-
-static void
-mt7623_trgmii_rmw(struct mt7530_priv *priv, u32 reg,
- u32 mask, u32 set)
-{
- u32 val;
-
- val = mt7623_trgmii_read(priv, reg);
- val &= ~mask;
- val |= set;
- mt7623_trgmii_write(priv, reg, val);
-}
-
-static void
-mt7623_trgmii_set(struct mt7530_priv *priv, u32 reg, u32 val)
-{
- mt7623_trgmii_rmw(priv, reg, 0, val);
-}
-
-static void
-mt7623_trgmii_clear(struct mt7530_priv *priv, u32 reg, u32 val)
-{
- mt7623_trgmii_rmw(priv, reg, val, 0);
-}
-
-static int
core_read_mmd_indirect(struct mt7530_priv *priv, int prtad, int devad)
{
struct mii_bus *bus = priv->bus;
@@ -530,27 +478,6 @@ mt7530_pad_clk_setup(struct dsa_switch *
for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
mt7530_rmw(priv, MT7530_TRGMII_RD(i),
RD_TAP_MASK, RD_TAP(16));
- else
- if (priv->id != ID_MT7621)
- mt7623_trgmii_set(priv, GSW_INTF_MODE,
- INTF_MODE_TRGMII);
-
- return 0;
-}
-
-static int
-mt7623_pad_clk_setup(struct dsa_switch *ds)
-{
- struct mt7530_priv *priv = ds->priv;
- int i;
-
- for (i = 0 ; i < NUM_TRGMII_CTRL; i++)
- mt7623_trgmii_write(priv, GSW_TRGMII_TD_ODT(i),
- TD_DM_DRVP(8) | TD_DM_DRVN(8));
-
- mt7623_trgmii_set(priv, GSW_TRGMII_RCK_CTRL, RX_RST | RXC_DQSISEL);
- mt7623_trgmii_clear(priv, GSW_TRGMII_RCK_CTRL, RX_RST);
-
return 0;
}
@@ -1258,10 +1185,6 @@ mt7530_setup(struct dsa_switch *ds)
dn = dsa_to_port(ds, MT7530_CPU_PORT)->master->dev.of_node->parent;
if (priv->id == ID_MT7530) {
- priv->ethernet = syscon_node_to_regmap(dn);
- if (IS_ERR(priv->ethernet))
- return PTR_ERR(priv->ethernet);
-
regulator_set_voltage(priv->core_pwr, 1000000, 1000000);
ret = regulator_enable(priv->core_pwr);
if (ret < 0) {
@@ -1427,14 +1350,6 @@ static void mt7530_phylink_mac_config(st
/* Setup TX circuit incluing relevant PAD and driving */
mt7530_pad_clk_setup(ds, state->interface);
- if (priv->id == ID_MT7530) {
- /* Setup RX circuit, relevant PAD and driving on the
- * host which must be placed after the setup on the
- * device side is all finished.
- */
- mt7623_pad_clk_setup(ds);
- }
-
priv->p6_interface = state->interface;
break;
default:
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -275,7 +275,6 @@ enum mt7530_vlan_port_attr {
/* Registers for TRGMII on the both side */
#define MT7530_TRGMII_RCK_CTRL 0x7a00
-#define GSW_TRGMII_RCK_CTRL 0x300
#define RX_RST BIT(31)
#define RXC_DQSISEL BIT(30)
#define DQSI1_TAP_MASK (0x7f << 8)
@@ -284,31 +283,24 @@ enum mt7530_vlan_port_attr {
#define DQSI0_TAP(x) ((x) & 0x7f)
#define MT7530_TRGMII_RCK_RTT 0x7a04
-#define GSW_TRGMII_RCK_RTT 0x304
#define DQS1_GATE BIT(31)
#define DQS0_GATE BIT(30)
#define MT7530_TRGMII_RD(x) (0x7a10 + (x) * 8)
-#define GSW_TRGMII_RD(x) (0x310 + (x) * 8)
#define BSLIP_EN BIT(31)
#define EDGE_CHK BIT(30)
#define RD_TAP_MASK 0x7f
#define RD_TAP(x) ((x) & 0x7f)
-#define GSW_TRGMII_TXCTRL 0x340
#define MT7530_TRGMII_TXCTRL 0x7a40
#define TRAIN_TXEN BIT(31)
#define TXC_INV BIT(30)
#define TX_RST BIT(28)
#define MT7530_TRGMII_TD_ODT(i) (0x7a54 + 8 * (i))
-#define GSW_TRGMII_TD_ODT(i) (0x354 + 8 * (i))
#define TD_DM_DRVP(x) ((x) & 0xf)
#define TD_DM_DRVN(x) (((x) & 0xf) << 4)
-#define GSW_INTF_MODE 0x390
-#define INTF_MODE_TRGMII BIT(1)
-
#define MT7530_TRGMII_TCK_CTRL 0x7a78
#define TCK_TAP(x) (((x) & 0xf) << 8)
@@ -441,7 +433,6 @@ static const char *p5_intf_modes(unsigne
* @ds: The pointer to the dsa core structure
* @bus: The bus used for the device and built-in PHY
* @rstc: The pointer to reset control used by MCM
- * @ethernet: The regmap used for access TRGMII-based registers
* @core_pwr: The power supplied into the core
* @io_pwr: The power supplied into the I/O
* @reset: The descriptor for GPIO line tied to its reset pin
@@ -458,7 +449,6 @@ struct mt7530_priv {
struct dsa_switch *ds;
struct mii_bus *bus;
struct reset_control *rstc;
- struct regmap *ethernet;
struct regulator *core_pwr;
struct regulator *io_pwr;
struct gpio_desc *reset;