RE: [PATCH v11 2/2] media: v4l: xilinx: Add Xilinx MIPI CSI-2 Rx Subsystem driver

[Vishal Sagar]

Hi Luca,

> -----Original Message-----
> From: Luca Ceresoli <luca@xxxxxxxxxxxxxxxx>
> Sent: Tuesday, April 21, 2020 1:16 PM
> To: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> Cc: Vishal Sagar <vsagar@xxxxxxxxxx>; Hyun Kwon <hyunk@xxxxxxxxxx>;
> mchehab@xxxxxxxxxx; robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx; Michal
> Simek <michals@xxxxxxxxxx>; linux-media@xxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; hans.verkuil@xxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Dinesh Kumar
> <dineshk@xxxxxxxxxx>; Sandip Kothari <sandipk@xxxxxxxxxx>; Jacopo Mondi
> <jacopo@xxxxxxxxxx>; Hyun Kwon <hyunk@xxxxxxxxxx>
> Subject: Re: [PATCH v11 2/2] media: v4l: xilinx: Add Xilinx MIPI CSI-2 Rx
> Subsystem driver
> 
> Hi Laurent,
> 
> On 20/04/20 21:57, Laurent Pinchart wrote:
> > Hi Luca,
> >
> > On Mon, Apr 20, 2020 at 09:24:25PM +0200, Luca Ceresoli wrote:
> >> On 19/04/20 20:02, Laurent Pinchart wrote:
> >> [...]
> >>>> +static irqreturn_t xcsi2rxss_irq_handler(int irq, void *dev_id) {
> >>>> +	struct xcsi2rxss_state *state = (struct xcsi2rxss_state *)dev_id;
> >>>> +	struct xcsi2rxss_core *core = &state->core;
> >>>> +	u32 status;
> >>>> +
> >>>> +	status = xcsi2rxss_read(core, XCSI_ISR_OFFSET) &
> XCSI_ISR_ALLINTR_MASK;
> >>>> +	dev_dbg_ratelimited(core->dev, "interrupt status = 0x%08x\n",
> >>>> +status);
> >>>
> >>> As this is expected to occur for every frame, I would drop the
> >>> message, even if rate-limited.
> >>>
> >>>> +
> >>>> +	if (!status)
> >>>> +		return IRQ_NONE;
> >>>> +
> >>>> +	/* Received a short packet */
> >>>> +	if (status & XCSI_ISR_SPFIFONE) {
> >>>> +		dev_dbg_ratelimited(core->dev, "Short packet = 0x%08x\n",
> >>>> +				    xcsi2rxss_read(core, XCSI_SPKTR_OFFSET));
> >>>> +	}
> >>>
> >>> Same here, this will occur all the time, I'd remove this message.
> >>> You need to read XCSI_SPKTR_OFFSET though, and you should do so in a
> >>> loop until the XCSI_CSR_SPFIFONE in XCSI_CSR_OFFSET is cleared in
> >>> case multiple short packets are received before the interrupt
> >>> handler executes.
> >>>
> >>> I also wonder if it would make sense to extract the frame number
> >>> from the FS short packet, and make it available through the subdev
> >>> API. I think it should be reported through a V4L2_EVENT_FRAME_SYNC
> >>> event. This can be implemented later.
> >>>
> >>>> +
> >>>> +	/* Short packet FIFO overflow */
> >>>> +	if (status & XCSI_ISR_SPFIFOF)
> >>>> +		dev_dbg_ratelimited(core->dev, "Short packet FIFO
> >>>> +overflowed\n");
> >>>> +
> >>>> +	/*
> >>>> +	 * Stream line buffer full
> >>>> +	 * This means there is a backpressure from downstream IP
> >>>> +	 */
> >>>> +	if (status & XCSI_ISR_SLBF) {
> >>>> +		dev_alert_ratelimited(core->dev, "Stream Line Buffer
> Full!\n");
> >>>> +		xcsi2rxss_stop_stream(state);
> >>>> +		if (core->rst_gpio) {
> >>>> +			gpiod_set_value(core->rst_gpio, 1);
> >>>> +			/* minimum 40 dphy_clk_200M cycles */
> >>>> +			ndelay(250);
> >>>> +			gpiod_set_value(core->rst_gpio, 0);
> >>>> +		}
> >>>
> >>> I don't think you should stop the core here. xcsi2rxss_stop_stream()
> >>> calls the source .s_stream(0) operation, which usually involves I2C
> >>> writes that will sleep.
> >>>
> >>> You should instead report an event to userspace (it looks like we
> >>> have no error event defined in V4L2, one should be added), and rely
> >>> on the normal stop procedure.
> >>
> >> FWIW, since a long time I've been using a modified version of this
> >> routine, where after a Stream Line Buffer Full condition I just stop
> >> and restart the csi2rx core and the stream continues after a minimal
> glitch.
> >> Other subdev are unaware that anything has happened and keep on
> streaming.
> >>
> >> Not sure this is the correct thing to do, but it's working for me.
> >> Also I proposed this topic in one of the previous iterations of this
> >> patch, but the situation was different because the stream on/off was
> >> not propagated back at that time.
> >
> > Thanks for the feedback. How often does this occur in practice ?
> 
> Quite often indeed in my case, as the MIPI stream comes from a remote
> sensor via a video serdes chipset, and both the cable and the remote sensor
> module are subject to heavy EMI. Depending on the setup I observed SLBF
> happening up to 5~10 times per hour.
> 
> --
> Luca

Thanks for sharing your observation.
Getting a stream line buffer full condition indicates a design issue.
Stopping, resetting using video_aresetn and starting is valid way to start MIPI CSI-2 Rx SS but masks the issue.
Hence the current implementation is to warn and stop streaming.

Regards
Vishal Sagar