[PATCH 4/6] Documentation: ABI: testing: scd30: document iio attributes

[Tomasz Duszynski]

Add documentation for sensor specific iio attributes.

Signed-off-by: Tomasz Duszynski <tomasz.duszynski@xxxxxxxxxxx>
---
 Documentation/ABI/testing/sysfs-bus-iio-scd30 | 97 +++++++++++++++++++
 1 file changed, 97 insertions(+)
 create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-scd30

diff --git a/Documentation/ABI/testing/sysfs-bus-iio-scd30 b/Documentation/ABI/testing/sysfs-bus-iio-scd30
new file mode 100644
index 000000000000..0431a718447d
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-scd30
@@ -0,0 +1,97 @@
+What:		/sys/bus/iio/devices/iio:deviceX/pressure_comp
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Given that sensor's CO2 measurement chamber has fixed volume
+		pressure changes will affect concentration readings. Writing
+		current ambient pressure here will allow senor to make necessary
+		adjustments. Upon reading previously set value is returned.
+		Units are millibars.
+
+What:		/sys/bus/iio/devices/iio:deviceX/pressure_comp_available
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		The range of available values in millibars represented as the
+		minimum value, the step and the maximum value, all enclosed in
+		square brackets.
+
+What:		/sys/bus/iio/devices/iio:deviceX/meas_interval
+Date:		January 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Amount of time between subsequent measurements. Writing this
+		attribute will change measurement interval. Upon reading
+		current measurement interval is returned. Units are seconds.
+
+What:		/sys/bus/iio/devices/iio:deviceX/meas_interval_available
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		The range of available values in seconds represented as the
+		minimum value, the step and the maximum value, all enclosed in
+		square brackets.
+
+What:		/sys/bus/iio/devices/iio:deviceX/asc
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Writing 1 or 0 to this attribute will respectively activate or
+		deactivate automatic self calibration procedure. Upon reading 1
+		is returned if asc is ongoing, 0 otherwise.
+
+What:		/sys/bus/iio/devices/iio:deviceX/frc
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Forced recalibration is used to compensate for sensor drifts
+		when a reference value of CO2 concentration in close proximity
+		to the sensor is available. Writing attribute will set frc
+		value. Upon reading current frc is returned. Units are
+		millibars.
+
+What:		/sys/bus/iio/devices/iio:deviceX/frc_available
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		The range of available values in millibars represented as the
+		minimum value, the step and the maximum value, all enclosed in
+		square brackets.
+
+What:		/sys/bus/iio/devices/iio:deviceX/temp_offset
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Sensor readings may be affected by ambient temperature.
+		Writing temperature offset will compensate for unwanted changes.
+		Note that written offset gets multiplied by a factor of 100
+		by a sensor internally.
+
+		For example, writing 10 here will correspond to 0.1 degree
+		Celsius.
+
+What:		/sys/bus/iio/devices/iio:deviceX/temp_offset_available
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		The range of available values in degrees Celsius represented as
+		the minimum value, the step and the maximum value, all enclosed
+		in square brackets.
+
+What:		/sys/bus/iio/devices/iio:deviceX/reset
+Date:		April 2020
+KernelVersion:	5.8
+Contact:	linux-iio@xxxxxxxxxxxxxxx
+Description:
+		Software reset mechanism forces sensor into the same state
+		as after powering up without the need for removing power supply.
+		Writing any value will reset sensor.
-- 
2.26.1