[PATCH] KVM: x86: pass correct DR6 for GD userspace exit

[Paolo Bonzini]

When KVM_EXIT_DEBUG is raised for the disabled-breakpoints case (DR7.GD),
DR6 was incorrectly copied from the value in the VM.  Instead,
DR6.BD should be set in order to catch this case.

Signed-off-by: Paolo Bonzini <pbonzini@xxxxxxxxxx>
---
 arch/x86/kvm/vmx/vmx.c                        |  2 +-
 .../testing/selftests/kvm/x86_64/debug_regs.c | 24 ++++++++++++++++++-
 2 files changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/x86/kvm/vmx/vmx.c b/arch/x86/kvm/vmx/vmx.c
index 2384a2dbec44..ce534336c115 100644
--- a/arch/x86/kvm/vmx/vmx.c
+++ b/arch/x86/kvm/vmx/vmx.c
@@ -4927,7 +4927,7 @@ static int handle_dr(struct kvm_vcpu *vcpu)
 		 * guest debugging itself.
 		 */
 		if (vcpu->guest_debug & KVM_GUESTDBG_USE_HW_BP) {
-			vcpu->run->debug.arch.dr6 = vcpu->arch.dr6;
+			vcpu->run->debug.arch.dr6 = DR6_BD | DR6_RTM | DR6_FIXED_1;
 			vcpu->run->debug.arch.dr7 = dr7;
 			vcpu->run->debug.arch.pc = kvm_get_linear_rip(vcpu);
 			vcpu->run->debug.arch.exception = DB_VECTOR;
diff --git a/tools/testing/selftests/kvm/x86_64/debug_regs.c b/tools/testing/selftests/kvm/x86_64/debug_regs.c
index 2b7187db061d..ed94c0b3da35 100644
--- a/tools/testing/selftests/kvm/x86_64/debug_regs.c
+++ b/tools/testing/selftests/kvm/x86_64/debug_regs.c
@@ -11,10 +11,13 @@
 
 #define VCPU_ID 0
 
+#define DR6_BD		(1 << 13)
+#define DR7_GD		(1 << 13)
+
 /* For testing data access debug BP */
 uint32_t guest_value;
 
-extern unsigned char sw_bp, hw_bp, write_data, ss_start;
+extern unsigned char sw_bp, hw_bp, write_data, ss_start, bd_start;
 
 static void guest_code(void)
 {
@@ -43,6 +46,8 @@ static void guest_code(void)
 		     "rdmsr\n\t"
 		     : : : "rax", "ecx");
 
+	/* DR6.BD test */
+	asm volatile("bd_start: mov %%dr0, %%rax" : : : "rax");
 	GUEST_DONE();
 }
 
@@ -165,6 +170,23 @@ int main(void)
 			    target_dr6);
 	}
 
+	/* Disable all debug controls, run to the end */
+	CLEAR_DEBUG();
+	debug.control = KVM_GUESTDBG_ENABLE | KVM_GUESTDBG_USE_HW_BP;
+	debug.arch.debugreg[7] = 0x400 | DR7_GD;
+	APPLY_DEBUG();
+	vcpu_run(vm, VCPU_ID);
+	target_dr6 = 0xffff0ff0 | DR6_BD;
+	TEST_ASSERT(run->exit_reason == KVM_EXIT_DEBUG &&
+		    run->debug.arch.exception == DB_VECTOR &&
+		    run->debug.arch.pc == CAST_TO_RIP(bd_start) &&
+		    run->debug.arch.dr6 == target_dr6,
+			    "DR7.GD: exit %d exception %d rip 0x%llx "
+			    "(should be 0x%llx) dr6 0x%llx (should be 0x%llx)",
+			    run->exit_reason, run->debug.arch.exception,
+			    run->debug.arch.pc, target_rip, run->debug.arch.dr6,
+			    target_dr6);
+
 	/* Disable all debug controls, run to the end */
 	CLEAR_DEBUG();
 	APPLY_DEBUG();
-- 
2.18.2