Re: [PATCH v2 1/2] media: dt-bindings: media: xilinx: Add Xilinx UHD-SDI Receiver Subsystem

[Laurent Pinchart]

Hi Vishal,

Thank you for the patch.

On Wed, Apr 29, 2020 at 07:47:03PM +0530, Vishal Sagar wrote:
> Add bindings documentation for Xilinx UHD-SDI Receiver Subsystem.
> 
> The Xilinx UHD-SDI Receiver Subsystem consists of SMPTE UHD-SDI (RX) IP
> core, an SDI RX to Video Bridge IP core to convert SDI video to native
> video and a Video In to AXI4-Stream IP core to convert native video to
> AXI4-Stream.
> 
> Signed-off-by: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> ---
> v2
> - Removed references to xlnx,video*
> - Fixed as per Sakari Ailus and Rob Herring's comments
> - Converted to yaml format
> 
>  .../bindings/media/xilinx/xlnx,sdirxss.yaml   | 132 ++++++++++++++++++
>  1 file changed, 132 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml
> 
> diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml
> new file mode 100644
> index 000000000000..9133ad19df55
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,sdirxss.yaml
> @@ -0,0 +1,132 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/xilinx/xlnx,sdirxss.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +
> +title: Xilinx SMPTE UHD-SDI Receiver Subsystem
> +
> +maintainers:
> +  - Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> +
> +description: |
> +  The SMPTE UHD-SDI Receiver (RX) Subsystem allows you to quickly create systems
> +  based on SMPTE SDI protocols. It receives unaligned native SDI streams from
> +  the SDI GT PHY and outputs an AXI4-Stream video stream, native video, or
> +  native SDI using Xilinx transceivers as the physical layer.
> +
> +  The subsystem consists of
> +  1 - SMPTE UHD-SDI Rx
> +  2 - SDI Rx to Native Video Bridge
> +  3 - Video In to AXI4-Stream Bridge
> +
> +  The subsystem can capture SDI streams in upto 12G mode 8 data streams and output

s/upto/up to/

> +  a dual pixel per clock RGB/YUV444,422/420 10/12 bits per component AXI4-Stream.
> +
> +properties:
> +  compatible:
> +    items:
> +      - enum:
> +        - xlnx,v-smpte-uhdsdi-rx-ss-2.0
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    description: List of clock specifiers
> +    items:
> +      - description: AXI4-Lite clock
> +      - description: SMPTE UHD-SDI Rx core clock
> +      - description: Video clock
> +
> +  clock-names:
> +    items:
> +      - const: s_axi_aclk
> +      - const: sdi_rx_clk
> +      - const: video_out_clk
> +
> +  xlnx,bpp:
> +    description: Bits per pixel supported. Can be 10 or 12 bits per pixel only.
> +    allOf:
> +      - $ref: "/schemas/types.yaml#/definitions/uint32"
> +      - enum: [10, 12]

I don't see this as a design parameter in the documentation (pg290,
v2.0). What does it correspond to ? All the BPC mentions in the
documentation always state that 10-bit is the only supported value.

> +
> +  xlnx,line-rate:
> +    description: |
> +      The maximum mode supported by the design. Possible values are as below
> +      12G_SDI_8DS - 12G mode with 8 data streams
> +      6G_SDI      -  6G mode
> +      3G_SDI      -  3G mode
> +    enum:
> +      - 12G_SDI_8DS
> +      - 6G_SDI
> +      - 3G_SDI

How about making this an integer property, with #define in
include/dt-bindings/media/xilinx-sdi.h ? As far as I understand, the SDI
TX subsystem has the same parameter, so the #define could be shared
between the two.

> +
> +  xlnx,include-edh:
> +    type: boolean
> +    description: |
> +      This is present when the Error Detection and Handling processor is
> +      enabled in design.
> +
> +  ports:
> +    type: object
> +    description: |
> +      Generally the SDI port is connected to a device like SDI Broadcast camera
> +      which is independently controlled. Hence port@0 is a source port which can be
> +      connected to downstream IP which can work with AXI4 Stream data.

We should still have an input port. It can be connected to a DT node for
a physical SDI connector, or any other component in the platform (I
expect the former to be the common case). There are DT bindings for
connectors in Documentation/devicetree/bindings/display/connector/, we
should add one for SDI.

> +    properties:
> +      port@0:
> +        type: object
> +        description: Source port
> +        properties:
> +          reg:
> +            const: 0
> +          endpoint:
> +            type: object
> +            properties:
> +              remote-endpoint: true
> +            required:
> +              - remote-endpoint
> +            additionalProperties: false
> +        additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - clock-names
> +  - xlnx,line-rate
> +  - xlnx,bpp
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    uhdsdirxss: v-smpte-uhdsdi-rxss@80000000 {
> +      compatible = "xlnx,v-smpte-uhdsdi-rx-ss-2.0";
> +      interrupt-parent = <&gic>;
> +      interrupts = <0 89 4>;
> +      reg = <0x0 0x80000000 0x0 0x10000>;
> +      xlnx,include-edh;
> +      xlnx,line-rate = "12G_SDI_8DS";
> +      clocks = <&clk_1>, <&si570_1>, <&clk_2>;
> +      clock-names = "s_axi_aclk", "sdi_rx_clk", "video_out_clk";
> +      xlnx,bpp = <10>;
> +
> +      ports {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +        port@0 {
> +          reg = <0>;
> +          sdirx_out: endpoint {
> +            remote-endpoint = <&vcap_sdirx_in>;
> +          };
> +        };
> +      };
> +    };

-- 
Regards,

Laurent Pinchart