[PATCH v9 1/5] usb: xhci: Change the XHCI link order in the Makefile

[Al Cooper]

Some BRCMSTB USB chips have an XHCI, EHCI and OHCI controller
on the same port where XHCI handles 3.0 devices, EHCI handles 2.0
devices and OHCI handles <2.0 devices. Currently the Makefile
has XHCI linking at the bottom which will result in the XHIC driver
initalizing after the EHCI and OHCI drivers and any installed 3.0
device will be seen as a 2.0 device. Moving the XHCI linking
above the EHCI and OHCI linking fixes the issue.

Signed-off-by: Al Cooper <alcooperx@xxxxxxxxx>
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>
---
 drivers/usb/host/Makefile | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index b191361257cc..a7f0b8ff7179 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -37,6 +37,16 @@ endif
 
 obj-$(CONFIG_USB_PCI)	+= pci-quirks.o
 
+# NOTE: BRCMSTB systems require that xhci driver be linked before the
+# ehci/ohci drivers because they share a port and need the XHCI driver
+# to come up first to properly enumerate 3.0 devices.
+obj-$(CONFIG_USB_XHCI_HCD)	+= xhci-hcd.o
+obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
+obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
+obj-$(CONFIG_USB_XHCI_HISTB)	+= xhci-histb.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
+obj-$(CONFIG_USB_XHCI_TEGRA)	+= xhci-tegra.o
+
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
 obj-$(CONFIG_USB_EHCI_HCD_PLATFORM)	+= ehci-platform.o
@@ -69,12 +79,6 @@ obj-$(CONFIG_USB_OHCI_HCD_DAVINCI)	+= ohci-da8xx.o
 
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
 obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
-obj-$(CONFIG_USB_XHCI_HCD)	+= xhci-hcd.o
-obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
-obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
-obj-$(CONFIG_USB_XHCI_HISTB)	+= xhci-histb.o
-obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
-obj-$(CONFIG_USB_XHCI_TEGRA)	+= xhci-tegra.o
 obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o
 obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
 obj-$(CONFIG_USB_U132_HCD)	+= u132-hcd.o
-- 
2.17.1