Re: [v2 3/4] regulator: qcom: Add labibb driver

[Bjorn Andersson]

On Fri 08 May 13:41 PDT 2020, Sumit Semwal wrote:

> From: Nisha Kumari <nishakumari@xxxxxxxxxxxxxx>
> 
> Qualcomm platforms have LAB(LCD AMOLED Boost)/IBB(Inverting Buck Boost)
> Regulators, labibb for short, which are used as power supply for

lowercase Regulators

> LCD Mode displays.
> 
> This patch adds labibb regulator driver for pmi8998 pmic, found on

Uppercase PMIC

> SDM845 platforms.
> 
> Signed-off-by: Nisha Kumari <nishakumari@xxxxxxxxxxxxxx>
> Signed-off-by: Sumit Semwal <sumit.semwal@xxxxxxxxxx>
> 
> --
> v2: sumits: reworked the driver for more common code, and addressed
>     review comments from v1. This includes merging regulator_ops into
>     one, and allowing for future labibb variations.
> ---
>  drivers/regulator/Kconfig                 |  10 +
>  drivers/regulator/Makefile                |   1 +
>  drivers/regulator/qcom-labibb-regulator.c | 288 ++++++++++++++++++++++
>  3 files changed, 299 insertions(+)
>  create mode 100644 drivers/regulator/qcom-labibb-regulator.c
> 
> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> index f4b72cb098ef..58704a9fd05d 100644
> --- a/drivers/regulator/Kconfig
> +++ b/drivers/regulator/Kconfig
> @@ -1167,5 +1167,15 @@ config REGULATOR_WM8994
>  	  This driver provides support for the voltage regulators on the
>  	  WM8994 CODEC.
>  
> +config REGULATOR_QCOM_LABIBB
> +	tristate "QCOM LAB/IBB regulator support"
> +	depends on SPMI || COMPILE_TEST
> +	help
> +	  This driver supports Qualcomm's LAB/IBB regulators present on the
> +	  Qualcomm's PMIC chip pmi8998. QCOM LAB and IBB are SPMI
> +	  based PMIC implementations. LAB can be used as positive
> +	  boost regulator and IBB can be used as a negative boost regulator
> +	  for LCD display panel.
> +
>  endif
>  
> diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
> index 6610ee001d9a..5b313786c0e8 100644
> --- a/drivers/regulator/Makefile
> +++ b/drivers/regulator/Makefile
> @@ -87,6 +87,7 @@ obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
>  obj-$(CONFIG_REGULATOR_MT6358)	+= mt6358-regulator.o
>  obj-$(CONFIG_REGULATOR_MT6380)	+= mt6380-regulator.o
>  obj-$(CONFIG_REGULATOR_MT6397)	+= mt6397-regulator.o
> +obj-$(CONFIG_REGULATOR_QCOM_LABIBB) += qcom-labibb-regulator.o
>  obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
>  obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
>  obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
> diff --git a/drivers/regulator/qcom-labibb-regulator.c b/drivers/regulator/qcom-labibb-regulator.c
> new file mode 100644
> index 000000000000..a9dc7c060375
> --- /dev/null
> +++ b/drivers/regulator/qcom-labibb-regulator.c
> @@ -0,0 +1,288 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (c) 2019, The Linux Foundation. All rights reserved.
> +
> +#include <linux/module.h>
> +#include <linux/of_irq.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/of_regulator.h>
> +
> +#define REG_PERPH_TYPE                  0x04
> +#define QCOM_LAB_TYPE			0x24
> +#define QCOM_IBB_TYPE			0x20
> +
> +#define REG_LABIBB_STATUS1		0x08
> +#define REG_LABIBB_ENABLE_CTL		0x46
> +#define LABIBB_STATUS1_VREG_OK_BIT	BIT(7)
> +#define LABIBB_CONTROL_ENABLE		BIT(7)
> +
> +#define LAB_ENABLE_CTL_MASK		BIT(7)
> +#define IBB_ENABLE_CTL_MASK		(BIT(7) | BIT(6))
> +
> +#define POWER_DELAY			8000
> +
> +struct labibb_regulator {
> +	struct regulator_desc		desc;
> +	struct device			*dev;
> +	struct regmap			*regmap;
> +	struct regulator_dev		*rdev;
> +	u16				base;
> +	u8				type;
> +};
> +
> +struct qcom_labibb {

You pretty much use this as a local variable within probe, and then you
use labibb_regulator in runtime. Perhaps you can just drop it?

> +	struct device			*dev;
> +	struct regmap			*regmap;
> +	struct labibb_regulator		lab;
> +	struct labibb_regulator		ibb;
> +};
> +
> +struct labibb_regulator_data {
> +	u16				base;
> +	const char			*name;
> +	const char			*irq_name;
> +	u8				type;
> +};
> +
> +static int qcom_labibb_regulator_is_enabled(struct regulator_dev *rdev)
> +{
> +	int ret;
> +	u8 val;
> +	struct labibb_regulator *reg = rdev_get_drvdata(rdev);
> +
> +	ret = regmap_bulk_read(reg->regmap, reg->base +
> +			       REG_LABIBB_STATUS1, &val, 1);
> +	if (ret < 0) {
> +		dev_err(reg->dev, "Read register failed ret = %d\n", ret);
> +		return ret;
> +	}
> +
> +	if (val & LABIBB_STATUS1_VREG_OK_BIT)
> +		return 1;
> +	else
> +		return 0;

	return !!(val & LABIBB_STATUS1_VREG_OK_BIT);

> +}
> +
> +static int _check_enabled_with_retries(struct regulator_dev *rdev,
> +			int retries, int enabled)
> +{
> +	int ret;
> +	struct labibb_regulator *reg = rdev_get_drvdata(rdev);
> +
> +	while (retries--) {

Mark's suggestion of extending _regulator_enable_delay() to support
polling is_enable() seems reasonable.

The only complication I can see is that code path currently doesn't have
any expectations of the regulator not being operational at the end -
this seems to offer that possibility. So some care needs to be taken
there.


But doing that would allow you to use regulator_enable_regmap() as your
.enable function directly and you can drop
qcom_labibb_regulator_enable()

> +		/* Wait for a small period before checking REG_LABIBB_STATUS1 */
> +		usleep_range(POWER_DELAY, POWER_DELAY + 200);
> +
> +		ret = qcom_labibb_regulator_is_enabled(rdev);
> +
> +		if (ret < 0) {
> +			dev_err(reg->dev, "Can't read %s regulator status\n",
> +				reg->desc.name);
> +			return ret;
> +		}
> +
> +		if (ret == enabled)
> +			return ret;
> +
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static int qcom_labibb_regulator_enable(struct regulator_dev *rdev)
> +{
> +	int ret, retries = 10;
> +	struct labibb_regulator *reg = rdev_get_drvdata(rdev);
> +
> +	ret = regulator_enable_regmap(rdev);
> +
> +	if (ret < 0) {
> +		dev_err(reg->dev, "Write failed: enable %s regulator\n",
> +			reg->desc.name);
> +		return ret;
> +	}
> +
> +	ret = _check_enabled_with_retries(rdev, retries, 1);
> +	if (ret < 0) {
> +		dev_err(reg->dev, "retries exhausted: enable %s regulator\n",
> +			reg->desc.name);
> +		return ret;
> +	}
> +
> +	if (ret)
> +		return 0;

This looks weird; check for timeout, check for errors and then return
success.

> +
> +
> +	dev_err(reg->dev, "Can't enable %s\n", reg->desc.name);
> +	return -EINVAL;
> +}
> +
> +static int qcom_labibb_regulator_disable(struct regulator_dev *rdev)
> +{
> +	int ret, retries = 2;
> +	struct labibb_regulator *reg = rdev_get_drvdata(rdev);
> +
> +	ret = regulator_disable_regmap(rdev);
> +
> +	if (ret < 0) {
> +		dev_err(reg->dev, "Write failed: disable %s regulator\n",
> +			reg->desc.name);
> +		return ret;
> +	}
> +
> +	ret = _check_enabled_with_retries(rdev, retries, 0);

I don't think we care about waiting for the regulator to turning off,
might be nice to ensure that an off/on cycle really is allowed to take
its time though. So specifying an desc->off_on_delay of 8200 * 2 (the
worst case usleep_range() * retries) should take care of this.

And then you should be able to just use regulator_disable_regmap() as
your .disable function.

> +	if (ret < 0) {
> +		dev_err(reg->dev, "retries exhausted: disable %s regulator\n",
> +			reg->desc.name);
> +		return ret;
> +	}
> +
> +	if (!ret)
> +		return 0;
> +
> +	dev_err(reg->dev, "Can't disable %s\n", reg->desc.name);
> +	return -EINVAL;
> +}
> +
> +static struct regulator_ops qcom_labibb_ops = {
> +	.enable			= qcom_labibb_regulator_enable,
> +	.disable		= qcom_labibb_regulator_disable,
> +	.is_enabled		= qcom_labibb_regulator_is_enabled,
> +};
> +
> +static int register_labibb_regulator(struct qcom_labibb *labibb,
> +				const struct labibb_regulator_data *reg_data,
> +				struct device_node *of_node)
> +{
> +	int ret;
> +	struct labibb_regulator *reg;
> +	struct regulator_config cfg = {};
> +
> +	if (reg_data->type == QCOM_LAB_TYPE) {
> +		reg = &labibb->lab;
> +		reg->desc.enable_mask = LAB_ENABLE_CTL_MASK;
> +	} else {
> +		reg = &labibb->ibb;
> +		reg->desc.enable_mask = IBB_ENABLE_CTL_MASK;
> +	}
> +
> +	reg->dev = labibb->dev;
> +	reg->base = reg_data->base;
> +	reg->type = reg_data->type;
> +	reg->regmap = labibb->regmap;
> +	reg->desc.enable_reg = reg->base + REG_LABIBB_ENABLE_CTL;
> +	reg->desc.enable_val = LABIBB_CONTROL_ENABLE;
> +	reg->desc.of_match = reg_data->name;
> +	reg->desc.name = reg_data->name;
> +	reg->desc.owner = THIS_MODULE;
> +	reg->desc.type = REGULATOR_VOLTAGE;
> +	reg->desc.ops = &qcom_labibb_ops;
> +
> +	cfg.dev = labibb->dev;
> +	cfg.driver_data = reg;
> +	cfg.regmap = labibb->regmap;
> +	cfg.of_node = of_node;
> +
> +	reg->rdev = devm_regulator_register(labibb->dev, &reg->desc,
> +							&cfg);

Do you really need to wrap this line?

> +	if (IS_ERR(reg->rdev)) {
> +		ret = PTR_ERR(reg->rdev);
> +		dev_err(labibb->dev,
> +			"unable to register %s regulator\n", reg_data->name);
> +		return ret;
> +	}
> +	return 0;

	return PTR_ERR_OR_ZERO(reg->rdev);

> +}
> +
> +static const struct labibb_regulator_data pmi8998_labibb_data[] = {
> +	{0xde00, "lab", "lab-sc-err", QCOM_LAB_TYPE},

Please shorten the interrupt to just "sc-err".

> +	{0xdc00, "ibb", "ibb-sc-err", QCOM_IBB_TYPE},
> +	{ },
> +};
> +
> +static const struct of_device_id qcom_labibb_match[] = {
> +	{ .compatible = "qcom,pmi8998-lab-ibb", .data = &pmi8998_labibb_data},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, qcom_labibb_match);
> +
> +static int qcom_labibb_regulator_probe(struct platform_device *pdev)
> +{
> +	struct qcom_labibb *labibb;
> +	struct device_node *child;
> +	const struct of_device_id *match;
> +	const struct labibb_regulator_data *reg;
> +	u8 type;
> +	int ret;
> +
> +	labibb = devm_kzalloc(&pdev->dev, sizeof(*labibb), GFP_KERNEL);
> +	if (!labibb)
> +		return -ENOMEM;
> +
> +	labibb->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> +	if (!labibb->regmap) {
> +		dev_err(&pdev->dev, "Couldn't get parent's regmap\n");
> +		return -ENODEV;
> +	}
> +
> +	labibb->dev = &pdev->dev;
> +
> +	match = of_match_device(qcom_labibb_match, &pdev->dev);
> +	if (!match)
> +		return -ENODEV;
> +
> +	for (reg = match->data; reg->name; reg++) {
> +		child = of_get_child_by_name(pdev->dev.of_node, reg->name);
> +
> +		/* TODO: This validates if the type of regulator is indeed
> +		 * what's mentioned in DT.
> +		 * I'm not sure if this is needed, but we'll keep it for now.
> +		 */
> +		ret = regmap_bulk_read(labibb->regmap,
> +					reg->base + REG_PERPH_TYPE,
> +					&type, 1);
> +		if (ret < 0) {
> +			dev_err(labibb->dev,
> +				"Peripheral type read failed ret=%d\n",
> +				ret);
> +			return -EINVAL;
> +		}
> +
> +		if ((type != QCOM_LAB_TYPE) && (type != QCOM_IBB_TYPE)) {
> +			dev_err(labibb->dev,
> +				"qcom_labibb: unknown peripheral type\n");
> +			return -EINVAL;
> +		} else if (type != reg->type) {
> +			dev_err(labibb->dev,
> +				"qcom_labibb: type read %x doesn't match DT %x\n",
> +				type, reg->type);
> +			return -EINVAL;
> +		}
> +
> +		ret = register_labibb_regulator(labibb, reg, child);
> +		if (ret < 0) {
> +			dev_err(&pdev->dev,
> +				"qcom_labibb: error registering %s regulator: %d\n",
> +				child->full_name, ret);

You already printed in register_labibb_regulator() so no need to print
again.

> +			return ret;
> +		}
> +	}
> +
> +	dev_set_drvdata(&pdev->dev, labibb);

rdev_get_drvdata() returns cfg.driver_data, so you don't need this one.

Regards,
Bjorn

> +	return 0;
> +}
> +
> +static struct platform_driver qcom_labibb_regulator_driver = {
> +	.driver		= {
> +		.name		= "qcom-lab-ibb-regulator",
> +		.of_match_table	= qcom_labibb_match,
> +	},
> +	.probe		= qcom_labibb_regulator_probe,
> +};
> +module_platform_driver(qcom_labibb_regulator_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm labibb driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.26.2
>