Re: [PATCH v4 00/16] mtd: spi-nor: add xSPI Octal DTR support

[Tudor.Ambarus]

Hi, Vignesh,

On Tuesday, May 12, 2020 12:49:07 PM EEST Vignesh Raghavendra wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the
> content is safe
> On 12/05/20 11:46 am, Tudor.Ambarus@xxxxxxxxxxxxx wrote:
> > Hi, Boris, Pratyush,
> > 
> > I stripped case 2/, we'll not treat it for now.
> > 
> > On Monday, May 11, 2020 12:27:12 PM EEST Boris Brezillon wrote:
> >> EXTERNAL EMAIL: Do not click links or open attachments unless you know
> >> the
> >> content is safe
> >> 
> >> On Mon, 11 May 2020 09:00:35 +0000
> >> 
> >> <Tudor.Ambarus@xxxxxxxxxxxxx> wrote:
> >>> Hi, Pratyush, Boris,
> >>> 
> >>> On Friday, April 24, 2020 9:43:54 PM EEST Pratyush Yadav wrote:
> >>>> This series adds support for octal DTR flashes in the spi-nor
> >>>> framework,
> >>> 
> >>> I'm still learning about this, but I can give you my 2 cents as of now,
> >>> to
> >>> open the discussion. Enabling 2-2-2, 4-4-4, and 8-8-8 modes is dangerous
> >>> because the flash may not recover from unexpected resets. Entering one
> >>> of
> >>> these modes can be:
> >>> 1/ volatile selectable, the device return to the 1-1-1 protocol after
> >>> the
> >>> next power-on. I guess this is conditioned by the optional RESET pin,
> >>> but
> >>> I'll have to check. Also the flash can return to the 1-1-1 mode using
> >>> the
> >>> software reset or through writing to its Configuration Register, without
> >>> power-on or power- off.
> >> 
> >> My understanding is that there's no standard software reset procedure
> >> that guarantees no conflict with existing 1S commands, so even the
> >> software reset approach doesn't work here.
> > 
> > The software reset procedure can't protect you from unexpected resets, but
> > the hardware with its optional reset pin can. Pratyush to confirm.
> > 
> > cut
> > 
> >>> Not recovering from unexpected resets is unacceptable. One should always
> >>> prefer option 1/ and condition the entering in 2-2-2, 4-4-4 and 8-8-8
> >>> with
> >>> the presence of the optional RESET pin.
> >> 
> >> Totally agree with you on that one, but we know what happens in
> >> practice...
> > 
> > What I proposed is to condition the entering in the state-full modes with
> > the presence of the optional RESET pin. We would introduce an optional
> > device tree property for the RESET pin. If hardware doesn't implement the
> > optional RESET# signal, then we will not enter in the state-full modes.
> 
> Are you asking for dedicated SW controllable reset line or just an
> indication from DT that OSPI reset line is connected to board level
> soft/hard reset lines?

I don't see a need for the reset line to be SW controllable, a simple 
indication from the device tree should be enough.

> 
> Mandating SW controllable RESET line is bit of a stretch IMO... Board
> design may not allow wasting dedicated pin due to lack of GPIOs perhaps..
> 
> For eg.: TI EVM has OSPI reset line connected to board level reset out.
> This ensures any soft/warm/hard CPU reset will trigger OSPI Flash reset,
> but there is no SW control that allows OSPI flash alone to be reset.
> Isn't such a reset mechanism sufficient?
> 

I think it is, yes.

Cheers,
ta