Re: [PATCHv2 10/10] net: eth: altera: update devicetree bindings documentation

[Rob Herring]

On Mon, May 04, 2020 at 04:25:58PM +0800, Joyce Ooi wrote:
> From: Dalon Westergreen <dalon.westergreen@xxxxxxxxx>
> 
> Update devicetree bindings documentation to include msgdma
> prefetcher and ptp bindings.
> 
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: devicetree@xxxxxxxxxxxxxxx
> Signed-off-by: Dalon Westergreen <dalon.westergreen@xxxxxxxxx>
> Signed-off-by: Joyce Ooi <joyce.ooi@xxxxxxxxx>
> ---
> v2: no change
> ---
>  .../devicetree/bindings/net/altera_tse.txt         | 103 +++++++++++++++++----
>  1 file changed, 84 insertions(+), 19 deletions(-)

Reviewed-by: Rob Herring <robh@xxxxxxxxxx>

One nit below.

> 
> diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt
> index 0b7d4d3758ea..2f2d12603907 100644
> --- a/Documentation/devicetree/bindings/net/altera_tse.txt
> +++ b/Documentation/devicetree/bindings/net/altera_tse.txt
> @@ -2,53 +2,86 @@
>  
>  Required properties:
>  - compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should
> -		be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE.
> +		be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE,
> +		and "altr,tse-msgdma-2.0" for MSGDMA with prefetcher based
> +		implementations.
>  		ALTR is supported for legacy device trees, but is deprecated.
>  		altr should be used for all new designs.
>  - reg: Address and length of the register set for the device. It contains
>    the information of registers in the same order as described by reg-names
>  - reg-names: Should contain the reg names
> -  "control_port": MAC configuration space region
> -  "tx_csr":       xDMA Tx dispatcher control and status space region
> -  "tx_desc":      MSGDMA Tx dispatcher descriptor space region
> -  "rx_csr" :      xDMA Rx dispatcher control and status space region
> -  "rx_desc":      MSGDMA Rx dispatcher descriptor space region
> -  "rx_resp":      MSGDMA Rx dispatcher response space region
> -  "s1":		  SGDMA descriptor memory
>  - interrupts: Should contain the TSE interrupts and it's mode.
>  - interrupt-names: Should contain the interrupt names
> -  "rx_irq":       xDMA Rx dispatcher interrupt
> -  "tx_irq":       xDMA Tx dispatcher interrupt
> +  "rx_irq":       DMA Rx dispatcher interrupt
> +  "tx_irq":       DMA Tx dispatcher interrupt
>  - rx-fifo-depth: MAC receive FIFO buffer depth in bytes
>  - tx-fifo-depth: MAC transmit FIFO buffer depth in bytes
>  - phy-mode: See ethernet.txt in the same directory.
>  - phy-handle: See ethernet.txt in the same directory.
>  - phy-addr: See ethernet.txt in the same directory. A configuration should
>  		include phy-handle or phy-addr.
> -- altr,has-supplementary-unicast:
> -		If present, TSE supports additional unicast addresses.
> -		Otherwise additional unicast addresses are not supported.
> -- altr,has-hash-multicast-filter:
> -		If present, TSE supports a hash based multicast filter.
> -		Otherwise, hash-based multicast filtering is not supported.
> -
>  - mdio device tree subnode: When the TSE has a phy connected to its local
>  		mdio, there must be device tree subnode with the following
>  		required properties:
> -
>  	- compatible: Must be "altr,tse-mdio".
>  	- #address-cells: Must be <1>.
>  	- #size-cells: Must be <0>.
>  
>  	For each phy on the mdio bus, there must be a node with the following
>  	fields:
> -
>  	- reg: phy id used to communicate to phy.
>  	- device_type: Must be "ethernet-phy".
>  
>  The MAC address will be determined using the optional properties defined in
>  ethernet.txt.
>  
> +- altr,has-supplementary-unicast:
> +		If present, TSE supports additional unicast addresses.
> +		Otherwise additional unicast addresses are not supported.
> +- altr,has-hash-multicast-filter:
> +		If present, TSE supports a hash based multicast filter.
> +		Otherwise, hash-based multicast filtering is not supported.
> +- altr,has-ptp:
> +		If present, TSE supports 1588 timestamping.  Currently only
> +		supported with the msgdma prefetcher.
> +- altr,tx-poll-cnt:
> +		Optional cycle count for Tx prefetcher to poll descriptor
> +		list.  If not present, defaults to 128, which at 125MHz is
> +		roughly 1usec. Only for "altr,tse-msgdma-2.0".
> +- altr,rx-poll-cnt:
> +		Optional cycle count for Tx prefetcher to poll descriptor
> +		list.  If not present, defaults to 128, which at 125MHz is
> +		roughly 1usec. Only for "altr,tse-msgdma-2.0".
> +
> +Required registers by compatibility string:
> + - "altr,tse-1.0"
> +	"control_port": MAC configuration space region
> +	"tx_csr":       DMA Tx dispatcher control and status space region
> +	"rx_csr" :      DMA Rx dispatcher control and status space region
> +	"s1":		DMA descriptor memory
> +
> + - "altr,tse-msgdma-1.0"
> +	"control_port": MAC configuration space region
> +	"tx_csr":       DMA Tx dispatcher control and status space region
> +	"tx_desc":      DMA Tx dispatcher descriptor space region
> +	"rx_csr" :      DMA Rx dispatcher control and status space region
> +	"rx_desc":      DMA Rx dispatcher descriptor space region
> +	"rx_resp":      DMA Rx dispatcher response space region
> +
> + - "altr,tse-msgdma-2.0"
> +	"control_port": MAC configuration space region
> +	"tx_csr":       DMA Tx dispatcher control and status space region
> +	"tx_pref":      DMA Tx prefetcher configuration space region
> +	"rx_csr" :      DMA Rx dispatcher control and status space region
> +	"rx_pref":      DMA Rx prefetcher configuration space region
> +	"tod_ctrl":     Time of Day Control register only required when
> +			timestamping support is enabled.  Timestamping is
> +			only supported with the msgdma-2.0 implementation.
> +
> +Optional properties:
> +- local-mac-address: See ethernet.txt in the same directory.
> +- max-frame-size: See ethernet.txt in the same directory.
> +
>  Example:
>  
>  	tse_sub_0_eth_tse_0: ethernet@1,00000000 {
> @@ -86,6 +119,11 @@ Example:
>  				device_type = "ethernet-phy";
>  			};
>  
> +			phy2: ethernet-phy@2 {
> +				reg = <0x2>;
> +				device_type = "ethernet-phy";
> +			};
> +
>  		};
>  	};
>  
> @@ -111,3 +149,30 @@ Example:
>  		altr,has-hash-multicast-filter;
>  		phy-handle = <&phy1>;
>  	};
> +
> +
> +	tse_sub_2_eth_tse_0: ethernet@1,00002000 {

What bus is this on? Usually a ',' like this is for a chip select 
number. If just a 64-bit address, then no comma.

> +		compatible = "altr,tse-msgdma-2.0";
> +		reg = 	<0x00000001 0x00002000 0x00000400>,
> +			<0x00000001 0x00002400 0x00000020>,
> +			<0x00000001 0x00002420 0x00000020>,
> +			<0x00000001 0x00002440 0x00000020>,
> +			<0x00000001 0x00002460 0x00000020>,
> +			<0x00000001 0x00002480 0x00000040>;
> +		reg-names = "control_port", "rx_csr", "rx_pref","tx_csr", "tx_pref", "tod_ctrl";
> +		interrupt-parent = <&hps_0_arm_gic_0>;
> +		interrupts = <0 45 4>, <0 44 4>;
> +		interrupt-names = "rx_irq", "tx_irq";
> +		rx-fifo-depth = <2048>;
> +		tx-fifo-depth = <2048>;
> +		address-bits = <48>;
> +		max-frame-size = <1500>;
> +		local-mac-address = [ 00 00 00 00 00 00 ];
> +		phy-mode = "sgmii";
> +		altr,has-supplementary-unicast;
> +		altr,has-hash-multicast-filter;
> +		altr,has-ptp;
> +		altr,tx-poll-cnt = <128>;
> +		altr,rx-poll-cnt = <32>;
> +		phy-handle = <&phy2>;
> +	};
> -- 
> 2.13.0
>