Re: [RFC v1 2/3] drivers: nvmem: Add driver for QTI qfprom-efuse support
From: Srinivas Kandagatla
Date: Wed May 13 2020 - 09:20:33 EST
On 12/05/2020 19:17, Ravi Kumar Bokka wrote:
This patch adds new driver for QTI qfprom-efuse controller. This driver can
access the raw qfprom regions for fuse blowing.
QTI?
The current existed qfprom driver is only supports for cpufreq, thermal sensors
drivers by read out calibration data, speed bins..etc which is stored
by qfprom efuses.
Can you explain bit more about this QFPROM instance, Is this QFPROM part
of secure controller address space?
Is this closely tied to SoC or Secure controller version?
Any reason why this can not be integrated into qfprom driver with
specific compatible.
Signed-off-by: Ravi Kumar Bokka <rbokka@xxxxxxxxxxxxxx>
---
drivers/nvmem/Kconfig | 10 +
drivers/nvmem/Makefile | 2 +
drivers/nvmem/qfprom-efuse.c | 476 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 488 insertions(+)
create mode 100644 drivers/nvmem/qfprom-efuse.c
...
diff --git a/drivers/nvmem/qfprom-efuse.c b/drivers/nvmem/qfprom-efuse.c
new file mode 100644
index 0000000..2e3c275
--- /dev/null
+++ b/drivers/nvmem/qfprom-efuse.c
@@ -0,0 +1,476 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+#define QFPROM_BLOW_STATUS_BUSY 0x1
+#define QFPROM_BLOW_STATUS_READY 0x0
+
+/* Blow timer clock frequency in Mhz for 10nm LPe technology */
+#define QFPROM_BLOW_TIMER_OFFSET 0x03c
+#define QFPROM_BLOW_TIMER_RESET_VALUE 0x0
+
+/* Amount of time required to hold charge to blow fuse in micro-seconds */
+#define QFPROM_FUSE_BLOW_POLL_PERIOD 100
+#define QFPROM_BLOW_STATUS_OFFSET 0x048
+
+#define QFPROM_ACCEL_OFFSET 0x044
+
+/**
+ * struct qfprom_efuse_platform_data - structure holding qfprom-efuse
+ * platform data
+ *
+ * @name: qfprom-efuse compatible name
??
+ * @fuse_blow_time_in_us: Should contain the wait time when doing the fuse blow
+ * @accel_value: Should contain qfprom accel value
+ * @accel_reset_value: The reset value of qfprom accel value
+ * @qfprom_blow_timer_value: The timer value of qfprom when doing efuse blow
+ * @qfprom_blow_reset_freq: The frequency required to set when fuse blowing
+ * is done
+ * @qfprom_blow_set_freq: The frequency required to set when we start the
+ * fuse blowing
+ * @qfprom_max_vol: max voltage required to set fuse blow
+ * @qfprom_min_vol: min voltage required to set fuse blow
How specific are these values per SoC?
+ */
+struct qfprom_efuse_platform_data {
+ const char *name;
+ u8 fuse_blow_time_in_us;
+ u32 accel_value;
+ u32 accel_reset_value;
+ u32 qfprom_blow_timer_value;
+ u32 qfprom_blow_reset_freq;
+ u32 qfprom_blow_set_freq;
+ u32 qfprom_max_vol;
+ u32 qfprom_min_vol;
+};
+
+/**
+ * struct qfprom_efuse_priv - structure holding qfprom-efuse attributes
+ *
+ * @qfpbase: iomapped memory space for qfprom base
+ * @qfpraw: iomapped memory space for qfprom raw fuse region
+ * @qfpmap: iomapped memory space for qfprom fuse blow timer
+
+ * @dev: qfprom device structure
+ * @secclk: clock supply
+ * @vcc: regulator supply
+
+ * @qfpraw_start: qfprom raw fuse start region
+ * @qfpraw_end: qfprom raw fuse end region
+ * @qfprom_efuse_platform_data: qfprom platform data
+ */
+struct qfprom_efuse_priv {
+ void __iomem *qfpbase;
+ void __iomem *qfpraw;
+ void __iomem *qfpmap;
Why are these memory regions split? Can't you just have complete qfprom
area and add fixed offset for qfpraw within the driver?
+ struct device *dev;
+ struct clk *secclk;
+ struct regulator *vcc;
+ resource_size_t qfpraw_start;
+ resource_size_t qfpraw_end;
Why do we need to check this range? as long as we set the nvmem_config
with correct range then you should not need this check.
+ struct qfprom_efuse_platform_data efuse;
A pointer here should be good enough?
+};
+
...
+/*
+ * sets the value of the blow timer, accel register and the clock
+ * and voltage settings
+ */
+static int qfprom_enable_fuse_blowing(const struct qfprom_efuse_priv *priv)
+{
+ int ret;
+
+ ret = qfprom_disable_fuse_blowing(priv);
+ if (ret) {
+ dev_err(priv->dev, "qfprom_disable_fuse_blowing()\n");
+ return ret;
+ }
Why do we need to qfprom_disable_fuse_blowing() for every call to enable it?
Or are we missing some error handling in the caller?
+
+ writel(priv->efuse.qfprom_blow_timer_value, priv->qfpmap +
+ QFPROM_BLOW_TIMER_OFFSET);
+ writel(priv->efuse.accel_value, priv->qfpmap + QFPROM_ACCEL_OFFSET);
+
+ ret = qfprom_set_clock_settings(priv);
+ if (ret) {
+ dev_err(priv->dev, "qpfrom_set_clock_settings()\n");
+ return ret;
+ }
+
+ ret = qfprom_set_voltage_settings(priv, priv->efuse.qfprom_min_vol,
+ priv->efuse.qfprom_max_vol);
+ if (ret) {
+ dev_err(priv->dev, "qfprom_set_voltage_settings()\n");
+ return ret;
+ }
+
+ return 0;
+}
+
<<
+/*
+ * verifying to make sure address being written or read is from qfprom
+ * raw address range
+ */
+bool addr_in_qfprom_range(const struct qfprom_efuse_priv *priv, u32 reg,
+ size_t bytes)
+{
+ if (((reg + bytes) > reg) && (reg >= priv->qfpraw_start) &&
+ ((reg + bytes) <= priv->qfpraw_end)) {
+ return 1;
+ }
+
+ return 0;
+}
>>
Above function is totally redundant, nvmem core already has checks for this.
+
+/*
+ * API for reading from raw qfprom region
+ */
+static int qfprom_efuse_reg_read(void *context, unsigned int reg, void *_val,
+ size_t bytes)
+{
+ struct qfprom_efuse_priv *priv = context;
+ u32 *value = _val;
+ u32 align_check;
+ int i = 0, words = bytes / 4;
+
+ dev_info(priv->dev,
+ "reading raw qfprom region offset: 0x%08x of size: %zd\n",
+ reg, bytes);
In general there is lot of debug info across the code, do you really
need all this? Consider removing these!
+
+ if (bytes % 4 != 0x00) {
+ dev_err(priv->dev,
+ "Bytes: %zd to read should be word align\n",
+ bytes);
+ return -EINVAL;
+ }
This word align check is also redundant once you set nvmem_config with
correct word_size.
+
+ if (!addr_in_qfprom_range(priv, reg, bytes)) {
+ dev_err(priv->dev,
+ "Invalid qfprom raw region offset 0x%08x & bytes %zd\n",
+ reg, bytes);
+ return -EINVAL;
+ }
+
+ align_check = (reg & 0xF);
+
+ if (((align_check & ~3) == align_check) && value != NULL)
+ while (words--)
+ *value++ = readl(priv->qfpbase + reg + (i++ * 4));
+
+ else
+ dev_err(priv->dev,
+ "Invalid input parameter 0x%08x fuse blow address\n",
+ reg);
+
+ return 0;
+}
...
+
+static int qfprom_efuse_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *qfpbase, *qfpraw, *qfpmap;
+ struct nvmem_device *nvmem;
+ struct nvmem_config *econfig;
+ struct qfprom_efuse_priv *priv;
+ const struct qfprom_efuse_platform_data *drvdata;
+ int ret;
+
+ dev_info(&pdev->dev, "[%s]: Invoked\n", __func__);
+
too much debug!
+ drvdata = of_device_get_match_data(&pdev->dev);
+ if (!drvdata)
+ return -EINVAL;
Unnecessary check as this driver will not be probed unless there is a
compatible match.
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->efuse.fuse_blow_time_in_us = drvdata->fuse_blow_time_in_us;
+ priv->efuse.accel_value = drvdata->accel_value;
+ priv->efuse.accel_reset_value = drvdata->accel_reset_value;
+ priv->efuse.qfprom_blow_timer_value = drvdata->qfprom_blow_timer_value;
+ priv->efuse.qfprom_blow_reset_freq = drvdata->qfprom_blow_reset_freq;
+ priv->efuse.qfprom_blow_set_freq = drvdata->qfprom_blow_set_freq;
+ priv->efuse.qfprom_max_vol = drvdata->qfprom_max_vol;
+ priv->efuse.qfprom_min_vol = drvdata->qfprom_min_vol;
+ priv->dev = dev;
+
+ qfpbase = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ priv->qfpbase = devm_ioremap_resource(dev, qfpbase);
+ if (IS_ERR(priv->qfpbase)) {
+ ret = PTR_ERR(priv->qfpbase);
+ goto err;
+ }
+
+ qfpraw = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+ priv->qfpraw = devm_ioremap_resource(dev, qfpraw);
+ if (IS_ERR(priv->qfpraw)) {
+ ret = PTR_ERR(priv->qfpraw);
+ goto err;
+ }
+
+ priv->qfpraw_start = qfpraw->start - qfpbase->start;
+ priv->qfpraw_end = qfpraw->end - qfpbase->start;
+
+ qfpmap = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+
+ priv->qfpmap = devm_ioremap_resource(dev, qfpmap);
+ if (IS_ERR(priv->qfpmap)) {
+ ret = PTR_ERR(priv->qfpmap);
+ goto err;
+ }
+
+ priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
I see no reference to this regulator in dt bindings.
+ if (IS_ERR(priv->vcc)) {
+ ret = PTR_ERR(priv->vcc);
+ if (ret == -ENODEV)
+ ret = -EPROBE_DEFER;
Can you explain what is going on here?
+
+ goto err;
+ }
+
+ priv->secclk = devm_clk_get(dev, "secclk");
+ if (IS_ERR(priv->secclk)) {
+ ret = PTR_ERR(priv->secclk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "secclk error getting : %d\n", ret);
+ goto err;
+ }
+
+ ret = clk_prepare_enable(priv->secclk);
+ if (ret) {
+ dev_err(dev, "clk_prepare_enable() failed\n");
+ goto err;
+ }
+
+ econfig = devm_kzalloc(dev, sizeof(*econfig), GFP_KERNEL);
+ if (!econfig)
Why not disabling the clk here?
+ return -ENOMEM;
+
+ econfig->dev = dev;
+ econfig->name = "qfprom-efuse";
+ econfig->stride = 1;
+ econfig->word_size = 1;
+ econfig->reg_read = qfprom_efuse_reg_read;
+ econfig->reg_write = qfprom_efuse_reg_write;
+ econfig->size = resource_size(qfpraw);
+ econfig->priv = priv;
+
+ nvmem = devm_nvmem_register(dev, econfig);
+
+ return PTR_ERR_OR_ZERO(nvmem);
probably you should check the nvmem here before returning to disable the
clk properly.
+
+err:
+ clk_disable_unprepare(priv->secclk);
+ return ret;
+}
+
+static const struct qfprom_efuse_platform_data sc7180_qfp_efuse_data = {
+ .name = "sc7180-qfprom-efuse",
Redundant.
+ .fuse_blow_time_in_us = 10,
+ .accel_value = 0xD10,
+ .accel_reset_value = 0x800,
+ .qfprom_blow_timer_value = 25,
+ .qfprom_blow_reset_freq = 19200000,
+ .qfprom_blow_set_freq = 4800000,
+ .qfprom_max_vol = 1904000,
+ .qfprom_min_vol = 1800000,
+};
+
+static const struct of_device_id qfprom_efuse_of_match[] = {
+ {
+ .compatible = "qcom,sc7180-qfprom-efuse",
+ .data = &sc7180_qfp_efuse_data
+ },
+ {/* sentinel */},
+};
+
+MODULE_DEVICE_TABLE(of, qfprom_efuse_of_match);
+
+static struct platform_driver qfprom_efuse_driver = {
+ .probe = qfprom_efuse_probe,
+ .driver = {
+ .name = "sc7180-qfprom-efuse",
+ .of_match_table = qfprom_efuse_of_match,
+ },
+};
+
+module_platform_driver(qfprom_efuse_driver);
+MODULE_DESCRIPTION("QTI QFPROM Efuse driver");
+MODULE_LICENSE("GPL v2");