[PATCH] tracing: Fix events.rst section numbering

[Tom Zanussi]

The in-kernel trace event API should have its own section, and the
duplicate section numbers need fixing as well.

Signed-off-by: Tom Zanussi <zanussi@xxxxxxxxxx>
Reported-by: Li Xinhai <lixinhai.lxh@xxxxxxxxx>
---
 Documentation/trace/events.rst | 28 ++++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

diff --git a/Documentation/trace/events.rst b/Documentation/trace/events.rst
index ed79b220bd07..1a3b7762cb0f 100644
--- a/Documentation/trace/events.rst
+++ b/Documentation/trace/events.rst
@@ -526,8 +526,8 @@ The following commands are supported:
 
   See Documentation/trace/histogram.rst for details and examples.
 
-6.3 In-kernel trace event API
------------------------------
+7. In-kernel trace event API
+============================
 
 In most cases, the command-line interface to trace events is more than
 sufficient.  Sometimes, however, applications might find the need for
@@ -559,8 +559,8 @@ following:
   - tracing synthetic events from in-kernel code
   - the low-level "dynevent_cmd" API
 
-6.3.1 Dyamically creating synthetic event definitions
------------------------------------------------------
+7.1 Dyamically creating synthetic event definitions
+---------------------------------------------------
 
 There are a couple ways to create a new synthetic event from a kernel
 module or other kernel code.
@@ -665,8 +665,8 @@ registered by calling the synth_event_gen_cmd_end() function:
 At this point, the event object is ready to be used for tracing new
 events.
 
-6.3.3 Tracing synthetic events from in-kernel code
---------------------------------------------------
+7.2 Tracing synthetic events from in-kernel code
+------------------------------------------------
 
 To trace a synthetic event, there are several options.  The first
 option is to trace the event in one call, using synth_event_trace()
@@ -677,8 +677,8 @@ synth_event_trace_start() and synth_event_trace_end() along with
 synth_event_add_next_val() or synth_event_add_val() to add the values
 piecewise.
 
-6.3.3.1 Tracing a synthetic event all at once
----------------------------------------------
+7.2.1 Tracing a synthetic event all at once
+-------------------------------------------
 
 To trace a synthetic event all at once, the synth_event_trace() or
 synth_event_trace_array() functions can be used.
@@ -779,8 +779,8 @@ remove the event:
 
        ret = synth_event_delete("schedtest");
 
-6.3.3.1 Tracing a synthetic event piecewise
--------------------------------------------
+7.2.2 Tracing a synthetic event piecewise
+-----------------------------------------
 
 To trace a synthetic using the piecewise method described above, the
 synth_event_trace_start() function is used to 'open' the synthetic
@@ -863,8 +863,8 @@ Note that synth_event_trace_end() must be called at the end regardless
 of whether any of the add calls failed (say due to a bad field name
 being passed in).
 
-6.3.4 Dyamically creating kprobe and kretprobe event definitions
-----------------------------------------------------------------
+7.3 Dyamically creating kprobe and kretprobe event definitions
+--------------------------------------------------------------
 
 To create a kprobe or kretprobe trace event from kernel code, the
 kprobe_event_gen_cmd_start() or kretprobe_event_gen_cmd_start()
@@ -940,8 +940,8 @@ used to give the kprobe event file back and delete the event:
 
   ret = kprobe_event_delete("gen_kprobe_test");
 
-6.3.4 The "dynevent_cmd" low-level API
---------------------------------------
+7.4 The "dynevent_cmd" low-level API
+------------------------------------
 
 Both the in-kernel synthetic event and kprobe interfaces are built on
 top of a lower-level "dynevent_cmd" interface.  This interface is
-- 
2.17.1