Re: XHCI vs PCM2903B/PCM2904 part 2

[Takashi Iwai]

On Wed, 20 May 2020 13:26:57 +0200,
Rik van Riel wrote:
> 
> After a few more weeks of digging, I have come to the tentative
> conclusion that either the XHCI driver, or the USB sound driver,
> or both, fail to handle USB errors correctly.
> 
> I have some questions at the bottom, after a (brief-ish) explanation
> of exactly what seems to go wrong.
> 
> TL;DR: arecord from a misbehaving device can hang forever
> after a USB error, due to poll on /dev/snd/timer never returning.
> 
> The details: under some mysterious circumstances, the PCM290x
> family sound chips can send more data than expected during an
> isochronous transfer, leading to a babble error. Those
> circumstances seem to in part depend on the USB host controller
> and/or the electrical environment, since the chips work just
> fine for most people.
> 
> Receiving data past the end of the isochronous transfer window
> scheduled for a device results in the XHCI controller throwing
> a babble error, which moves the endpoint into halted state.
> 
> This is followed by the host controller software sending a
> reset endpoint command, and moving the endpoint into stopped
> state, as specified on pages 164-165 of the XHCI specification.
> 
> However, the USB sound driver seems to have no idea that this
> error happened. The function retire_capture_urb looks at the
> status of each isochronous frame, but seems to be under the
> assumption that the sound device just keeps on running.
> 
> The function snd_complete_urb seems to only detect that the
> device is not running if usb_submit_urb returns a failure.
> 
>         err = usb_submit_urb(urb, GFP_ATOMIC);
>         if (err == 0)
>                 return;
> 
>         usb_audio_err(ep->chip, "cannot submit urb (err = %d)\n", err);
> 
>         if (ep->data_subs && ep->data_subs->pcm_substream) {
>                 substream = ep->data_subs->pcm_substream;
>                 snd_pcm_stop_xrun(substream);
>         }
> 
> However, the XHCI driver will happily submit an URB to a
> stopped device. Looking at the call trace usb_submit_urb ->
> xhci_urb_enqueue -> xhci_queue_isoc_tx_prepare -> prepare_ring,
> you can see this code:
> 
>         /* Make sure the endpoint has been added to xHC schedule */
>         switch (ep_state) {
> ...
>         case EP_STATE_HALTED:
>                 xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n");
>         case EP_STATE_STOPPED:
>         case EP_STATE_RUNNING:
>                 break;
> 
> This leads me to a few questions:
> - should retire_capture_urb call snd_pcm_stop_xrun,
>   or another function like it, if it sees certain
>   errors in the iso frame in the URB?

I guess it makes sense, yes.

> - should snd_complete_urb do something with these
>   errors, too, in case they happen on the sync frames
>   and not the data frames?

Ditto, the error can be handled similarly.

> - does the XHCI code need to ring the doorbell when
>   submitting an URB to a stopped device, or is it
>   always up to the higher-level driver to fully reset
>   the device before it can do anything useful?
> - if a device in stopped state does not do anything
>   useful, should usb_submit_urb return an error?
> - how should the USB sound driver recover from these
>   occasional and/or one-off errors? stop the sound
>   stream, or try to reinitialize the device and start
>   recording again?

When snd_pcm_stop_xrun() is called, it stops the stream and sets in
XRUN state.  Then the application receives -EPIPE error upon the next
access, and the application needs to re-setup the stream and restart.


Takashi

> 
> I am willing to write patches and can test with my
> setup, but both the sound code and the USB code are
> new to me so I would like to know what direction I
> should go in :)
> 
> -- 
> All Rights Reversed.
> [2 This is a digitally signed message part <application/pgp-signature (7bit)>]
>