Re: [PATCH v2 07/12] i2c: designware: Move Baytrail sem config to the platform if-clause

[Jarkko Nikula]

On 5/10/20 12:50 PM, Serge Semin wrote:
> Currently Intel Baytrail I2C semaphore is a feature of the DW APB I2C
> platform driver. It's a bit confusing to see it's config in the menu at
> some separated place with no reference to the platform code. Lets move the
> config definition under the if-I2C_DESIGNWARE_PLATFORM clause. By doing so
> the config menu will display the feature right below the DW I2C platform
> driver item and will indent it to the right so signifying its belonging.
>
> Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> Cc: Alexey Malahov <Alexey.Malahov@xxxxxxxxxxxxxxxxxxxx>
> Cc: Thomas Bogendoerfer <tsbogend@xxxxxxxxxxxxxxxx>
> Cc: Paul Burton <paulburton@xxxxxxxxxx>
> Cc: Ralf Baechle <ralf@xxxxxxxxxxxxxx>
> Cc: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
> Cc: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
> Cc: Wolfram Sang <wsa@xxxxxxxxxxxxx>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: Frank Rowand <frowand.list@xxxxxxxxx>
> Cc: linux-mips@xxxxxxxxxxxxxxx
> Cc: devicetree@xxxxxxxxxxxxxxx
> ---
>   drivers/i2c/busses/Kconfig | 30 +++++++++++++++++-------------
>   1 file changed, 17 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 368aa64e9266..ed6927c4c540 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -530,8 +530,8 @@ config I2C_DESIGNWARE_CORE
>   
>   config I2C_DESIGNWARE_PLATFORM
>   	tristate "Synopsys DesignWare Platform"
> -	select I2C_DESIGNWARE_CORE
>   	depends on (ACPI && COMMON_CLK) || !ACPI
> +	select I2C_DESIGNWARE_CORE
>   	help
>   	  If you say yes to this option, support will be included for the
>   	  Synopsys DesignWare I2C adapter.
> @@ -539,6 +539,22 @@ config I2C_DESIGNWARE_PLATFORM
>   	  This driver can also be built as a module.  If so, the module
>   	  will be called i2c-designware-platform.
>   
> +if I2C_DESIGNWARE_PLATFORM
> +
> +config I2C_DESIGNWARE_BAYTRAIL
> +	bool "Intel Baytrail I2C semaphore support"
> +	depends on ACPI
> +	depends on (I2C_DESIGNWARE_PLATFORM=m && IOSF_MBI) || \
> +		   (I2C_DESIGNWARE_PLATFORM=y && IOSF_MBI=y)
> +	help
> +	  This driver enables managed host access to the PMIC I2C bus on select
> +	  Intel BayTrail platforms using the X-Powers AXP288 PMIC. It allows
> +	  the host to request uninterrupted access to the PMIC's I2C bus from
> +	  the platform firmware controlling it. You should say Y if running on
> +	  a BayTrail system using the AXP288.
> +
> +endif # I2C_DESIGNWARE_PLATFORM
> +

Is the added "if I2C_DESIGNWARE_PLATFORM" needed here? Should the 
"depends on" be enough?

Jarkko