Re: [PATCH v12 3/3] i2c: npcm7xx: Add support for slave mode for Nuvoton

[Andy Shevchenko]

On Thu, May 21, 2020 at 02:09:10PM +0300, Tali Perry wrote:
> Add support for slave mode for Nuvoton
> NPCM BMC I2C controller driver.

...

> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> +/*
> + * npcm_i2caddr array:
> + * The module supports having multiple own slave addresses.
> + * Since the addr regs are sprinkled all over the address space,
> + * use this array to get the address or each register.
> + */
> +#define I2C_NUM_OWN_ADDR 10
> +const int  npcm_i2caddr[I2C_NUM_OWN_ADDR] = {NPCM_I2CADDR1, NPCM_I2CADDR2,

Extra spaces.
On top. please start assignment from the new line.

> +					     NPCM_I2CADDR3, NPCM_I2CADDR4,
> +					     NPCM_I2CADDR5, NPCM_I2CADDR6,
> +					     NPCM_I2CADDR7, NPCM_I2CADDR8,

> +					     NPCM_I2CADDR9, NPCM_I2CADDR10};

Split }; to new line and leave comma with the last member.

> +#endif

...

> +static int  npcm_i2c_slave_enable(struct npcm_i2c *bus, enum i2c_addr addr_type,
> +				  u8 addr, bool enable)

Extra spaces. Check entire patch for that and fix accordingly.

> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> +	if (bus->slave)

> +		npcm_i2c_slave_enable(bus, I2C_SLAVE_ADDR1, bus->slave->addr,
> +				      true);

I would leave this on one line.

> +#endif

...

> +static void npcm_i2c_write_fifo_slave(struct npcm_i2c *bus, u16 max_bytes)
> +{
> +	u8 size_free_fifo;

+ blank line.

> +	/*
> +	 * Fill the FIFO, while the FIFO is not full and there are more bytes
> +	 * to write
> +	 */
> +	npcm_i2c_clear_fifo_int(bus);
> +	npcm_i2c_clear_tx_fifo(bus);
> +	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);

> +	size_free_fifo = I2C_HW_FIFO_SIZE - npcm_i2c_fifo_usage(bus);

Dup, move into loop.

> +	while (max_bytes-- && size_free_fifo) {
> +		if (bus->slv_wr_size > 0) {
> +			bus->slv_wr_ind = bus->slv_wr_ind % I2C_HW_FIFO_SIZE;
> +			npcm_i2c_wr_byte(bus, bus->slv_wr_buf[bus->slv_wr_ind]);
> +			bus->slv_wr_ind++;
> +			bus->slv_wr_ind = bus->slv_wr_ind % I2C_HW_FIFO_SIZE;
> +			bus->slv_wr_size--;
> +			size_free_fifo = I2C_HW_FIFO_SIZE -
> +					 npcm_i2c_fifo_usage(bus);
> +		} else {
> +			break;
> +		}
> +	}

	while (...) {
		if (...)
			break;
		...
	}

> +}

...

> +static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
> +{
> +	int i;

> +	u8 value = 0;

Redundant assignment.

> +	int ind;
> +	int ret = bus->slv_wr_ind;
> +
> +	/* fill a cyclic buffer */
> +	for (i = 0; i < I2C_HW_FIFO_SIZE; i++) {
> +		if (bus->slv_wr_size >= I2C_HW_FIFO_SIZE)
> +			break;
> +		i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
> +		ind = (bus->slv_wr_ind + bus->slv_wr_size) % I2C_HW_FIFO_SIZE;
> +		bus->slv_wr_buf[ind] = value;
> +		bus->slv_wr_size++;
> +		i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
> +	}
> +	return I2C_HW_FIFO_SIZE - ret;
> +}

-- 
With Best Regards,
Andy Shevchenko