Re: [PATCH] hwmon (pmbus/max20730): add max20710 and debugfs access support

From: Guenter Roeck
Date: Thu May 28 2020 - 11:37:01 EST

Next message: Jami Kettunen: "Re: [PATCH] clk: qcom: Add missing msm8998 ufs_unipro_core_clk_src"
Previous message: Ramuthevar,Vadivel MuruganX: "[PATCH v9 2/2] mtd: rawnand: Add NAND controller support on Intel LGM SoC"
In reply to: Ugur Usug: "[PATCH] hwmon (pmbus/max20730): add max20710 and debugfs access support"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, May 26, 2020 at 09:42:19AM +0000, Ugur Usug wrote:
> This change has 2 parts:
> 1. Add support for max20710 into the existing max20730 driver.
>
> 2. Add debugfs interface support for accessing device specific registers
> (MFR_VOUT_MIN, MFR_DEVSET1 and MFR_DEVSET2) and others
> including OPERATION, ON_OFF_CONFIG, SMB_ALERT_MASK,
> VOUT_MODE, VOUT_COMMAND and VOUT_MAX.

This should be two separate patches. Please split and resubmit.

Thanks,
Guenter

>
> Signed-off-by: Ugur Usug <ugur.usug@xxxxxxxxxxxxxxxxxxx>
> ---
> Documentation/hwmon/max20730.rst | 10 +-
> drivers/hwmon/pmbus/Kconfig | 4 +-
> drivers/hwmon/pmbus/max20730.c | 412 ++++++++++++++++++++++++++++++++++++++-
> 3 files changed, 414 insertions(+), 12 deletions(-)
> mode change 100644 => 100755 drivers/hwmon/pmbus/max20730.c
>
> diff --git a/Documentation/hwmon/max20730.rst b/Documentation/hwmon/max20730.rst
> index cea7ae5..cb0c95b 100644
> --- a/Documentation/hwmon/max20730.rst
> +++ b/Documentation/hwmon/max20730.rst
> @@ -5,6 +5,14 @@ Kernel driver max20730
>
> Supported chips:
>
> + * Maxim MAX20710
> +
> + Prefix: 'max20710'
> +
> + Addresses scanned: -
> +
> + Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX20710.pdf
> +
> * Maxim MAX20730
>
> Prefix: 'max20730'
> @@ -35,7 +43,7 @@ Author: Guenter Roeck <linux@xxxxxxxxxxxx>
> Description
> -----------
>
> -This driver implements support for Maxim MAX20730, MAX20734, and MAX20743
> +This driver implements support for Maxim MAX20710, MAX20730, MAX20734, and MAX20743
> Integrated, Step-Down Switching Regulators with PMBus support.
>
> The driver is a client driver to the core PMBus driver.
> diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
> index de12a56..cac96e0 100644
> --- a/drivers/hwmon/pmbus/Kconfig
> +++ b/drivers/hwmon/pmbus/Kconfig
> @@ -147,10 +147,10 @@ config SENSORS_MAX16064
> be called max16064.
>
> config SENSORS_MAX20730
> - tristate "Maxim MAX20730, MAX20734, MAX20743"
> + tristate "Maxim MAX20710, MAX20730, MAX20734, MAX20743"
> help
> If you say yes here you get hardware monitoring support for Maxim
> - MAX20730, MAX20734, and MAX20743.
> + MAX20710, MAX20730, MAX20734, and MAX20743.
>
> This driver can also be built as a module. If so, the module will
> be called max20730.
> diff --git a/drivers/hwmon/pmbus/max20730.c b/drivers/hwmon/pmbus/max20730.c
> old mode 100644
> new mode 100755
> index c0bb054..fc38be0
> --- a/drivers/hwmon/pmbus/max20730.c
> +++ b/drivers/hwmon/pmbus/max20730.c
> @@ -1,12 +1,14 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> /*
> - * Driver for MAX20730, MAX20734, and MAX20743 Integrated, Step-Down
> - * Switching Regulators
> + * Driver for MAX20710, MAX20730, MAX20734, and MAX20743 Integrated,
> + * Step-Down Switching Regulators
> *
> * Copyright 2019 Google LLC.
> + * Copyright 2020 Maxim Integrated
> */
>
> #include <linux/bits.h>
> +#include <linux/debugfs.h>
> #include <linux/err.h>
> #include <linux/i2c.h>
> #include <linux/init.h>
> @@ -19,21 +21,283 @@
> #include "pmbus.h"
>
> enum chips {
> + max20710,
> max20730,
> max20734,
> max20743
> };
>
> +enum {
> + MAX20730_DEBUGFS_VOUT_MIN = 0,
> + MAX20730_DEBUGFS_FREQUENCY,
> + MAX20730_DEBUGFS_PG_DELAY,
> + MAX20730_DEBUGFS_INTERNAL_GAIN,
> + MAX20730_DEBUGFS_BOOT_VOLTAGE,
> + MAX20730_DEBUGFS_OUT_V_RAMP_RATE,
> + MAX20730_DEBUGFS_OC_PROTECT_MODE,
> + MAX20730_DEBUGFS_SS_TIMING,
> + MAX20730_DEBUGFS_IMAX,
> + MAX20730_DEBUGFS_OPERATION,
> + MAX20730_DEBUGFS_ON_OFF_CONFIG,
> + MAX20730_DEBUGFS_SMBALERT_MASK,
> + MAX20730_DEBUGFS_VOUT_MODE,
> + MAX20730_DEBUGFS_VOUT_COMMAND,
> + MAX20730_DEBUGFS_VOUT_MAX,
> + MAX20730_DEBUGFS_NUM_ENTRIES
> +};
> +
> struct max20730_data {
> enum chips id;
> struct pmbus_driver_info info;
> struct mutex lock; /* Used to protect against parallel writes */
> u16 mfr_devset1;
> + u16 mfr_devset2;
> + u16 mfr_voutmin;
> };
>
> #define to_max20730_data(x) container_of(x, struct max20730_data, info)
>
> +#define PMBUS_SMB_ALERT_MASK 0x1B
> +
> +#define MAX20730_MFR_VOUT_MIN 0xd1
> #define MAX20730_MFR_DEVSET1 0xd2
> +#define MAX20730_MFR_DEVSET2 0xd3
> +
> +#define MAX20730_MFR_VOUT_MIN_MASK GENMASK(9, 0)
> +#define MAX20730_MFR_VOUT_MIN_BIT_POS 0
> +
> +#define MAX20730_MFR_DEVSET1_RGAIN_MASK (BIT(13) | BIT(14))
> +#define MAX20730_MFR_DEVSET1_OTP_MASK (BIT(11) | BIT(12))
> +#define MAX20730_MFR_DEVSET1_VBOOT_MASK (BIT(8) | BIT(9))
> +#define MAX20730_MFR_DEVSET1_OCP_MASK (BIT(5) | BIT(6))
> +#define MAX20730_MFR_DEVSET1_FSW_MASK GENMASK(4, 2)
> +#define MAX20730_MFR_DEVSET1_TSTAT_MASK (BIT(0) | BIT(1))
> +
> +#define MAX20730_MFR_DEVSET1_RGAIN_BIT_POS 13
> +#define MAX20730_MFR_DEVSET1_OTP_BIT_POS 11
> +#define MAX20730_MFR_DEVSET1_VBOOT_BIT_POS 8
> +#define MAX20730_MFR_DEVSET1_OCP_BIT_POS 5
> +#define MAX20730_MFR_DEVSET1_FSW_BIT_POS 2
> +#define MAX20730_MFR_DEVSET1_TSTAT_BIT_POS 0
> +
> +#define MAX20730_MFR_DEVSET2_IMAX_MASK GENMASK(10, 8)
> +#define MAX20730_MFR_DEVSET2_VRATE (BIT(6) | BIT(7))
> +#define MAX20730_MFR_DEVSET2_OCPM_MASK BIT(5)
> +#define MAX20730_MFR_DEVSET2_SS_MASK (BIT(0) | BIT(1))
> +
> +#define MAX20730_MFR_DEVSET2_IMAX_BIT_POS 8
> +#define MAX20730_MFR_DEVSET2_VRATE_BIT_POS 6
> +#define MAX20730_MFR_DEVSET2_OCPM_BIT_POS 5
> +#define MAX20730_MFR_DEVSET2_SS_BIT_POS 0
> +
> +#define DEBUG_FS_DATA_MAX 8
> +
> +struct max20730_debugfs_data {
> + struct i2c_client *client;
> + int debugfs_entries[MAX20730_DEBUGFS_NUM_ENTRIES];
> +};
> +
> +#define to_psu(x, y) container_of((x), \
> + struct max20730_debugfs_data, debugfs_entries[(y)])
> +
> +static ssize_t max20730_debugfs_read(struct file *file, char __user *buf,
> + size_t count, loff_t *ppos)
> +{
> + int ret, len;
> + int *idxp = file->private_data;
> + int idx = *idxp;
> + struct max20730_debugfs_data *psu = to_psu(idxp, idx);
> + const struct pmbus_driver_info *info;
> + const struct max20730_data *data;
> + char tbuf[DEBUG_FS_DATA_MAX + 2] = { 0 };
> + u16 val;
> +
> + info = pmbus_get_driver_info(psu->client);
> + data = to_max20730_data(info);
> +
> + switch (idx) {
> + case MAX20730_DEBUGFS_VOUT_MIN:
> + len = snprintf(tbuf, 5, "%d", data->mfr_voutmin);
> + break;
> + case MAX20730_DEBUGFS_FREQUENCY:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_FSW_MASK)
> + >> MAX20730_MFR_DEVSET1_FSW_BIT_POS;
> + if (val == 0)
> + ret = 400;
> + else if (val == 1)
> + ret = 500;
> + else if (val == 2 || val == 3)
> + ret = 600;
> + else if (val == 4)
> + ret = 700;
> + else if (val == 5)
> + ret = 800;
> + else
> + ret = 900;
> + len = snprintf(tbuf, 4, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_PG_DELAY:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_TSTAT_MASK)
> + >> MAX20730_MFR_DEVSET1_TSTAT_BIT_POS;
> +
> + if (val == 0)
> + strcpy(tbuf, "2000");
> + else if (val == 1)
> + strcpy(tbuf, "125");
> + else if (val == 2)
> + strcpy(tbuf, "62.5");
> + else
> + strcpy(tbuf, "32");
> + len = strnlen(tbuf, DEBUG_FS_DATA_MAX);
> + break;
> +
> + case MAX20730_DEBUGFS_INTERNAL_GAIN:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_RGAIN_MASK)
> + >> MAX20730_MFR_DEVSET1_RGAIN_BIT_POS;
> +
> + if (data->id == max20734) {
> + /* AN6209 */
> + if (val == 0)
> + strcpy(tbuf, "0.8");
> + else if (val == 1)
> + strcpy(tbuf, "3.2");
> + else if (val == 2)
> + strcpy(tbuf, "1.6");
> + else
> + strcpy(tbuf, "6.4");
> + } else if (data->id == max20730 || data->id == max20710) {
> + /* AN6042 or AN6140 */
> + if (val == 0)
> + strcpy(tbuf, "0.9");
> + else if (val == 1)
> + strcpy(tbuf, "3.6");
> + else if (val == 2)
> + strcpy(tbuf, "1.8");
> + else
> + strcpy(tbuf, "7.2");
> + } else if (data->id == max20743) {
> + /* AN6042 */
> + if (val == 0)
> + strcpy(tbuf, "0.45");
> + else if (val == 1)
> + strcpy(tbuf, "1.8");
> + else if (val == 2)
> + strcpy(tbuf, "0.9");
> + else
> + strcpy(tbuf, "3.6");
> + } else
> + return -EINVAL;
> +
> + len = strnlen(tbuf, DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_BOOT_VOLTAGE:
> + val = (data->mfr_devset1 & MAX20730_MFR_DEVSET1_VBOOT_MASK)
> + >> MAX20730_MFR_DEVSET1_VBOOT_BIT_POS;
> +
> + if (val == 0)
> + strcpy(tbuf, "0.6484");
> + else if (val == 1)
> + strcpy(tbuf, "0.8984");
> + else if (val == 2)
> + strcpy(tbuf, "1.0");
> + else
> + return -EINVAL;
> +
> + len = strnlen(tbuf, DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_OUT_V_RAMP_RATE:
> + val = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_VRATE)
> + >> MAX20730_MFR_DEVSET2_VRATE_BIT_POS;
> +
> + if (val == 0)
> + ret = 4;
> + else if (val == 1)
> + ret = 2;
> + else if (val == 2)
> + ret = 1;
> + else
> + return -EINVAL;
> +
> + len = snprintf(tbuf, 2, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_OC_PROTECT_MODE:
> + ret = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_OCPM_MASK)
> + >> MAX20730_MFR_DEVSET2_OCPM_BIT_POS;
> + len = snprintf(tbuf, 2, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_SS_TIMING:
> + val = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_SS_MASK)
> + >> MAX20730_MFR_DEVSET2_SS_BIT_POS;
> +
> + if (val == 0)
> + strcpy(tbuf, "0.75");
> + else if (val == 1)
> + strcpy(tbuf, "1.5");
> + else if (val == 2)
> + strcpy(tbuf, "3");
> + else
> + strcpy(tbuf, "6");
> +
> + len = strnlen(tbuf, DEBUG_FS_DATA_MAX);
> + break;
> + case MAX20730_DEBUGFS_IMAX:
> + ret = (data->mfr_devset2 & MAX20730_MFR_DEVSET2_IMAX_MASK)
> + >> MAX20730_MFR_DEVSET2_IMAX_BIT_POS;
> + len = snprintf(tbuf, 2, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_OPERATION:
> + ret = i2c_smbus_read_byte_data(psu->client, PMBUS_OPERATION);
> + if(ret < 0)
> + return ret;
> + len = snprintf(tbuf, 2, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_ON_OFF_CONFIG:
> + ret = i2c_smbus_read_byte_data(psu->client, PMBUS_ON_OFF_CONFIG);
> + if(ret < 0)
> + return ret;
> + len = snprintf(tbuf, 2, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_SMBALERT_MASK:
> + ret = i2c_smbus_read_word_data(psu->client,
> + PMBUS_SMB_ALERT_MASK);
> + if(ret < 0)
> + return ret;
> + len = snprintf(tbuf, 3, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_VOUT_MODE:
> + ret = i2c_smbus_read_byte_data(psu->client, PMBUS_VOUT_MODE);
> + if(ret < 0)
> + return ret;
> + len = snprintf(tbuf, 2, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_VOUT_COMMAND:
> + ret = i2c_smbus_read_word_data(psu->client, PMBUS_VOUT_COMMAND);
> + if(ret < 0)
> + return ret;
> + len = snprintf(tbuf, 3, "%d", ret);
> + break;
> + case MAX20730_DEBUGFS_VOUT_MAX:
> + ret = i2c_smbus_read_word_data(psu->client, PMBUS_VOUT_MAX);
> + if(ret < 0)
> + return ret;
> + len = snprintf(tbuf, 3, "%d", ret);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + tbuf[len] = '\n';
> + len += 2;
> +
> + return simple_read_from_buffer(buf, count, ppos, tbuf, len);
> +}
> +
> +static const struct file_operations max20730_fops = {
> + .llseek = noop_llseek,
> + .read = max20730_debugfs_read,
> + .write = NULL,
> + .open = simple_open,
> +};
>
> /*
> * Convert discreet value to direct data format. Strictly speaking, all passed
> @@ -80,6 +344,7 @@ static long direct_to_val(u16 w, enum pmbus_sensor_classes class,
> }
>
> static u32 max_current[][5] = {
> + [max20710] = { 6200, 8000, 9700, 11600 },
> [max20730] = { 13000, 16600, 20100, 23600 },
> [max20734] = { 21000, 27000, 32000, 38000 },
> [max20743] = { 18900, 24100, 29200, 34100 },
> @@ -164,6 +429,45 @@ static int max20730_write_word_data(struct i2c_client *client, int page,
> }
>
> static const struct pmbus_driver_info max20730_info[] = {
> + [max20710] = {
> + .pages = 1,
> + .read_word_data = max20730_read_word_data,
> + .write_word_data = max20730_write_word_data,
> +
> + /* Source : Maxim AN6140 and AN6042 */
> + .format[PSC_TEMPERATURE] = direct,
> + .m[PSC_TEMPERATURE] = 21,
> + .b[PSC_TEMPERATURE] = 5887,
> + .R[PSC_TEMPERATURE] = -1,
> +
> + .format[PSC_VOLTAGE_IN] = direct,
> + .m[PSC_VOLTAGE_IN] = 3609,
> + .b[PSC_VOLTAGE_IN] = 0,
> + .R[PSC_VOLTAGE_IN] = -2,
> +
> + /*
> + * Values in the datasheet are adjusted for temperature and
> + * for the relationship between Vin and Vout.
> + * Unfortunately, the data sheet suggests that Vout measurement
> + * may be scaled with a resistor array. This is indeed the case
> + * at least on the evaulation boards. As a result, any in-driver
> + * adjustments would either be wrong or require elaborate means
> + * to configure the scaling. Instead of doing that, just report
> + * raw values and let userspace handle adjustments.
> + */
> + .format[PSC_CURRENT_OUT] = direct,
> + .m[PSC_CURRENT_OUT] = 153,
> + .b[PSC_CURRENT_OUT] = 4976,
> + .R[PSC_CURRENT_OUT] = -1,
> +
> + .format[PSC_VOLTAGE_OUT] = linear,
> +
> + .func[0] = PMBUS_HAVE_VIN |
> + PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> + PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_STATUS_INPUT,
> + },
> [max20730] = {
> .pages = 1,
> .read_word_data = max20730_read_word_data,
> @@ -200,7 +504,8 @@ static const struct pmbus_driver_info max20730_info[] = {
> .func[0] = PMBUS_HAVE_VIN |
> PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> - PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_STATUS_INPUT,
> },
> [max20734] = {
> .pages = 1,
> @@ -228,7 +533,8 @@ static const struct pmbus_driver_info max20730_info[] = {
> .func[0] = PMBUS_HAVE_VIN |
> PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> - PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_STATUS_INPUT,
> },
> [max20743] = {
> .pages = 1,
> @@ -256,7 +562,8 @@ static const struct pmbus_driver_info max20730_info[] = {
> .func[0] = PMBUS_HAVE_VIN |
> PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
> PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
> - PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP,
> + PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
> + PMBUS_HAVE_STATUS_INPUT,
> },
> };
>
> @@ -267,14 +574,17 @@ static int max20730_probe(struct i2c_client *client,
> u8 buf[I2C_SMBUS_BLOCK_MAX + 1];
> struct max20730_data *data;
> enum chips chip_id;
> - int ret;
> + int i, ret;
> + struct dentry *debugfs;
> + struct dentry *max20730_dir;
> + struct max20730_debugfs_data *psu;
>
> if (!i2c_check_functionality(client->adapter,
> I2C_FUNC_SMBUS_READ_BYTE_DATA |
> I2C_FUNC_SMBUS_READ_WORD_DATA |
> I2C_FUNC_SMBUS_BLOCK_DATA))
> return -ENODEV;
> -
> +
> ret = i2c_smbus_read_block_data(client, PMBUS_MFR_ID, buf);
> if (ret < 0) {
> dev_err(&client->dev, "Failed to read Manufacturer ID\n");
> @@ -335,10 +645,93 @@ static int max20730_probe(struct i2c_client *client,
> return ret;
> data->mfr_devset1 = ret;
>
> - return pmbus_do_probe(client, id, &data->info);
> + ret = pmbus_do_probe(client, id, &data->info);
> + if (ret < 0)
> + return ret;
> +
> +#if IS_ENABLED(CONFIG_DEBUG_FS)
> + ret = i2c_smbus_read_word_data(client, MAX20730_MFR_DEVSET2);
> + if (ret < 0)
> + return ret;
> + data->mfr_devset2 = ret;
> +
> + ret = i2c_smbus_read_word_data(client, MAX20730_MFR_VOUT_MIN);
> + if (ret < 0)
> + return ret;
> + data->mfr_voutmin = ret;
> +
> + /*
> + * Don't fail the probe if there isn't enough memory for debugfs.
> + */
> + psu = devm_kzalloc(&client->dev, sizeof(*psu), GFP_KERNEL);
> + if (!psu)
> + return 0;
> + psu->client = client;
> +
> + /* Don't fail the probe if we can't create debugfs */
> + debugfs = pmbus_get_debugfs_dir(client);
> + if (!debugfs)
> + return 0;
> +
> + max20730_dir = debugfs_create_dir(client->name, debugfs);
> + if (!max20730_dir)
> + return 0;
> +
> + for (i = 0; i < MAX20730_DEBUGFS_NUM_ENTRIES; ++i)
> + psu->debugfs_entries[i] = i;
> +
> + debugfs_create_file("vout_min", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_MIN],
> + &max20730_fops);
> + debugfs_create_file("frequency", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_FREQUENCY],
> + &max20730_fops);
> + debugfs_create_file("power_good_delay", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_PG_DELAY],
> + &max20730_fops);
> + debugfs_create_file("internal_gain", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_INTERNAL_GAIN],
> + &max20730_fops);
> + debugfs_create_file("boot_voltage", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_BOOT_VOLTAGE],
> + &max20730_fops);
> + debugfs_create_file("out_voltage_ramp_rate", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_OUT_V_RAMP_RATE],
> + &max20730_fops);
> + debugfs_create_file("oc_protection_mode", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_OC_PROTECT_MODE],
> + &max20730_fops);
> + debugfs_create_file("soft_start_timing", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_SS_TIMING],
> + &max20730_fops);
> + debugfs_create_file("imax", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_IMAX],
> + &max20730_fops);
> + debugfs_create_file("operation", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_OPERATION],
> + &max20730_fops);
> + debugfs_create_file("on_off_config", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_ON_OFF_CONFIG],
> + &max20730_fops);
> + debugfs_create_file("smbalert_mask", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_SMBALERT_MASK],
> + &max20730_fops);
> + debugfs_create_file("vout_mode", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_MODE],
> + &max20730_fops);
> + debugfs_create_file("vout_command", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_COMMAND],
> + &max20730_fops);
> + debugfs_create_file("vout_max", 0444, max20730_dir,
> + &psu->debugfs_entries[MAX20730_DEBUGFS_VOUT_MAX],
> + &max20730_fops);
> +#endif
> +
> + return 0;
> }
>
> static const struct i2c_device_id max20730_id[] = {
> + { "max20710", max20710 },
> { "max20730", max20730 },
> { "max20734", max20734 },
> { "max20743", max20743 },
> @@ -348,6 +741,7 @@ static const struct i2c_device_id max20730_id[] = {
> MODULE_DEVICE_TABLE(i2c, max20730_id);
>
> static const struct of_device_id max20730_of_match[] = {
> + { .compatible = "maxim,max20710", .data = (void *)max20710 },
> { .compatible = "maxim,max20730", .data = (void *)max20730 },
> { .compatible = "maxim,max20734", .data = (void *)max20734 },
> { .compatible = "maxim,max20743", .data = (void *)max20743 },
> @@ -369,5 +763,5 @@ static struct i2c_driver max20730_driver = {
> module_i2c_driver(max20730_driver);
>
> MODULE_AUTHOR("Guenter Roeck <linux@xxxxxxxxxxxx>");
> -MODULE_DESCRIPTION("PMBus driver for Maxim MAX20730 / MAX20734 / MAX20743");
> +MODULE_DESCRIPTION("PMBus driver for Maxim MAX20710 / MAX20730 / MAX20734 / MAX20743");
> MODULE_LICENSE("GPL");
> --
> 2.7.4
>

Next message: Jami Kettunen: "Re: [PATCH] clk: qcom: Add missing msm8998 ufs_unipro_core_clk_src"
Previous message: Ramuthevar,Vadivel MuruganX: "[PATCH v9 2/2] mtd: rawnand: Add NAND controller support on Intel LGM SoC"
In reply to: Ugur Usug: "[PATCH] hwmon (pmbus/max20730): add max20710 and debugfs access support"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]