R: [PATCH v5 11/11] PCI: qcom: Add Force GEN1 support

From: ansuelsmth
Date: Tue Jun 02 2020 - 13:07:35 EST


> On Tue, Jun 02, 2020 at 01:53:52PM +0200, Ansuel Smith wrote:
> > From: Sham Muthayyan <smuthayy@xxxxxxxxxxxxxx>
> >
> > Add Force GEN1 support needed in some ipq8064 board that needs to
> limit
> > some PCIe line to gen1 for some hardware limitation. This is set by the
> > max-link-speed binding and needed by some soc based on ipq8064. (for
> > example Netgear R7800 router)
> >
> > Signed-off-by: Sham Muthayyan <smuthayy@xxxxxxxxxxxxxx>
> > Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
> > Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> > ---
> > drivers/pci/controller/dwc/pcie-qcom.c | 13 +++++++++++++
> > 1 file changed, 13 insertions(+)
> >
> > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c
> b/drivers/pci/controller/dwc/pcie-qcom.c
> > index 259b627bf890..0ce15d53c46e 100644
> > --- a/drivers/pci/controller/dwc/pcie-qcom.c
> > +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> > @@ -27,6 +27,7 @@
> > #include <linux/slab.h>
> > #include <linux/types.h>
> >
> > +#include "../../pci.h"
> > #include "pcie-designware.h"
> >
> > #define PCIE20_PARF_SYS_CTRL 0x00
> > @@ -99,6 +100,8 @@
> > #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE 0x358
> > #define SLV_ADDR_SPACE_SZ 0x10000000
> >
> > +#define PCIE20_LNK_CONTROL2_LINK_STATUS2 0xa0
> > +
> > #define DEVICE_TYPE_RC 0x4
> >
> > #define QCOM_PCIE_2_1_0_MAX_SUPPLY 3
> > @@ -195,6 +198,7 @@ struct qcom_pcie {
> > struct phy *phy;
> > struct gpio_desc *reset;
> > const struct qcom_pcie_ops *ops;
> > + int gen;
> > };
> >
> > #define to_qcom_pcie(x) dev_get_drvdata((x)->dev)
> > @@ -395,6 +399,11 @@ static int qcom_pcie_init_2_1_0(struct
> qcom_pcie *pcie)
> > /* wait for clock acquisition */
> > usleep_range(1000, 1500);
> >
> > + if (pcie->gen == 1) {
> > + val = readl(pci->dbi_base +
> PCIE20_LNK_CONTROL2_LINK_STATUS2);
> > + val |= 1;
>
> Is this the same bit that's visible in config space as
> PCI_EXP_LNKSTA_CLS_2_5GB? Why not use that #define?
>
> There are a bunch of other #defines in this file that look like
> redefinitions of standard things:
>
> #define PCIE20_COMMAND_STATUS 0x04
> Looks like PCI_COMMAND
>
> #define CMD_BME_VAL 0x4
> Looks like PCI_COMMAND_MASTER
>
> #define PCIE20_DEVICE_CONTROL2_STATUS2 0x98
> Looks like (PCIE20_CAP + PCI_EXP_DEVCTL2)
>
> #define PCIE_CAP_CPL_TIMEOUT_DISABLE 0x10
> Looks like PCI_EXP_DEVCTL2_COMP_TMOUT_DIS
>
> #define PCIE20_CAP 0x70
> This one is obviously device-specific
>
> #define PCIE20_CAP_LINK_CAPABILITIES (PCIE20_CAP + 0xC)
> Looks like (PCIE20_CAP + PCI_EXP_LNKCAP)
>
> #define PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT (BIT(10) |
> BIT(11))
> Looks like PCI_EXP_LNKCAP_ASPMS
>
> #define PCIE20_CAP_LINK_1 (PCIE20_CAP + 0x14)
> #define PCIE_CAP_LINK1_VAL 0x2FD7F
> This looks like PCIE20_CAP_LINK_1 should be (PCIE20_CAP +
> PCI_EXP_SLTCAP), but "CAP_LINK_1" doesn't sound like the Slot
> Capabilities register, and I don't know what PCIE_CAP_LINK1_VAL
> means.
>

The define are used by ipq8074 and I really can't test the changes. Anyway
it shouldn't make a difference use the define instead of the custom value so
a patch should not harm anything... Problem is the last 2 define that we
really
don't know what they are about... How should I proceed? Change only the
value related to PCI_EXP_LNKSTA_CLS_2_5GB or change all the other except the

last 2?


> > + writel(val, pci->dbi_base +
> PCIE20_LNK_CONTROL2_LINK_STATUS2);
> > + }
> >
> > /* Set the Max TLP size to 2K, instead of using default of 4K */
> > writel(CFG_REMOTE_RD_REQ_BRIDGE_SIZE_2K,
> > @@ -1397,6 +1406,10 @@ static int qcom_pcie_probe(struct
> platform_device *pdev)
> > goto err_pm_runtime_put;
> > }
> >
> > + pcie->gen = of_pci_get_max_link_speed(pdev->dev.of_node);
> > + if (pcie->gen < 0)
> > + pcie->gen = 2;
> > +
> > res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> "parf");
> > pcie->parf = devm_ioremap_resource(dev, res);
> > if (IS_ERR(pcie->parf)) {
> > --
> > 2.25.1
> >