Re: [PATCH] serial: 8250_port: Fix imprecise external abort for mctrl if inactive

[Tony Lindgren]

* Tony Lindgren <tony@xxxxxxxxxxx> [200602 13:38]:
> * Andy Shevchenko <andy.shevchenko@xxxxxxxxx> [200602 08:33]:
> Now that we can detach and reattach the kernel serial console,
> there should not be any need for pm_runtime_irq_safe() anymore :)

Below is a hastily tested RFC patch to remove pm_runtime_irq_safe()
for 8250_omap.c that seems to work for idle use case :)

> And the UART wake-up from deeper idle states can only happen with
> help of external hardware like GPIO controller or pinctrl controller.

It does not yet include the check for configured wakeirq though.
And omap-serial.c needs a similar patch or maybe we can attempt
to just drop it this time as 8250_omap.c should be used nowadays.
Or just drop PM from omap-serial.c if it can't be dropped.

Andy, is the change below the only remaining blocker now for
your serial PM runtime changes?

Regards,

Tony

8< -------------------------------
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -123,6 +123,7 @@ struct omap8250_priv {
 	spinlock_t rx_dma_lock;
 	bool rx_dma_broken;
 	bool throttled;
+	unsigned int active:1;
 };
 
 struct omap8250_dma_params {
@@ -598,9 +599,13 @@ static irqreturn_t omap8250_irq(int irq, void *dev_id)
 {
 	struct uart_port *port = dev_id;
 	struct uart_8250_port *up = up_to_u8250p(port);
+	struct omap8250_priv *priv = up->port.private_data;
 	unsigned int iir;
 	int ret;
 
+	if (!priv->active)
+		return IRQ_NONE;
+
 #ifdef CONFIG_SERIAL_8250_DMA
 	if (up->dma) {
 		ret = omap_8250_dma_handle_irq(port);
@@ -608,10 +613,10 @@ static irqreturn_t omap8250_irq(int irq, void *dev_id)
 	}
 #endif
 
-	serial8250_rpm_get(up);
 	iir = serial_port_in(port, UART_IIR);
 	ret = serial8250_handle_irq(port, iir);
-	serial8250_rpm_put(up);
+
+	pm_runtime_mark_last_busy(port->dev);
 
 	return IRQ_RETVAL(ret);
 }
@@ -1110,13 +1115,9 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
 	unsigned long flags;
 	u8 iir;
 
-	serial8250_rpm_get(up);
-
 	iir = serial_port_in(port, UART_IIR);
-	if (iir & UART_IIR_NO_INT) {
-		serial8250_rpm_put(up);
+	if (iir & UART_IIR_NO_INT)
 		return IRQ_HANDLED;
-	}
 
 	spin_lock_irqsave(&port->lock, flags);
 
@@ -1144,7 +1145,7 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
 	}
 
 	uart_unlock_and_check_sysrq(port, flags);
-	serial8250_rpm_put(up);
+
 	return 1;
 }
 
@@ -1329,11 +1330,10 @@ static int omap8250_probe(struct platform_device *pdev)
 	if (!of_get_available_child_count(pdev->dev.of_node))
 		pm_runtime_set_autosuspend_delay(&pdev->dev, -1);
 
-	pm_runtime_irq_safe(&pdev->dev);
-
 	pm_runtime_get_sync(&pdev->dev);
 
 	omap_serial_fill_features_erratas(&up, priv);
+	priv->active = pm_runtime_enabled(&pdev->dev);
 	up.port.handle_irq = omap8250_no_handle_irq;
 	priv->rx_trigger = RX_TRIGGER;
 	priv->tx_trigger = TX_TRIGGER;
@@ -1517,6 +1517,8 @@ static int omap8250_runtime_suspend(struct device *dev)
 	if (!priv)
 		return 0;
 
+	priv->active = 0;
+
 	up = serial8250_get_port(priv->line);
 	/*
 	 * When using 'no_console_suspend', the console UART must not be
@@ -1575,6 +1577,8 @@ static int omap8250_runtime_resume(struct device *dev)
 
 	pinctrl_pm_select_default_state(dev);
 
+	priv->active = 1;
+
 	return 0;
 }
 #endif
-- 
2.26.2