[PATCH V3 2/3] dt-bindings: spi: Convert imx cspi to json-schema
From: Anson Huang
Date: Tue Jun 16 2020 - 00:37:34 EST
Convert the i.MX CSPI binding to DT schema format using json-schema,
update compatible, remove obsolete properties "fsl,spi-num-chipselects"
and update the example based on latest DT file.
Signed-off-by: Anson Huang <Anson.Huang@xxxxxxx>
---
Changes since V2:
- remove redundant "maxItems" in "clocks" and "clock-names".
---
.../devicetree/bindings/spi/fsl-imx-cspi.txt | 56 -------------
.../devicetree/bindings/spi/fsl-imx-cspi.yaml | 97 ++++++++++++++++++++++
2 files changed, 97 insertions(+), 56 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
create mode 100644 Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
deleted file mode 100644
index 33bc58f..0000000
--- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt
+++ /dev/null
@@ -1,56 +0,0 @@
-* Freescale (Enhanced) Configurable Serial Peripheral Interface
- (CSPI/eCSPI) for i.MX
-
-Required properties:
-- compatible :
- - "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1
- - "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21
- - "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27
- - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31
- - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35
- - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51
- - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc
- - "fsl,imx8mq-ecspi" for SPI compatible with the one integrated on i.MX8MQ
- - "fsl,imx8mm-ecspi" for SPI compatible with the one integrated on i.MX8MM
- - "fsl,imx8mn-ecspi" for SPI compatible with the one integrated on i.MX8MN
- - "fsl,imx8mp-ecspi" for SPI compatible with the one integrated on i.MX8MP
-- reg : Offset and length of the register set for the device
-- interrupts : Should contain CSPI/eCSPI interrupt
-- clocks : Clock specifiers for both ipg and per clocks.
-- clock-names : Clock names should include both "ipg" and "per"
-See the clock consumer binding,
- Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-Recommended properties:
-- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip
-select lines can be used, they appear to always generate a pulse between each
-word of a transfer. Most use cases will require GPIO based chip selects to
-generate a valid transaction.
-
-Optional properties:
-- num-cs : Number of total chip selects, see spi-bus.txt.
-- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
-Documentation/devicetree/bindings/dma/dma.txt.
-- dma-names: DMA request names, if present, should include "tx" and "rx".
-- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register
-controlling the SPI_READY handling. Note that to enable the DRCTL consideration,
-the SPI_READY mode-flag needs to be set too.
-Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst).
-
-Obsolete properties:
-- fsl,spi-num-chipselects : Contains the number of the chipselect
-
-Example:
-
-ecspi@70010000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx51-ecspi";
- reg = <0x70010000 0x4000>;
- interrupts = <36>;
- cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
- <&gpio3 25 0>; /* GPIO3_25 */
- dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
- dma-names = "rx", "tx";
- fsl,spi-rdy-drctl = <1>;
-};
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml
new file mode 100644
index 0000000..6e44c9c
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/fsl-imx-cspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale (Enhanced) Configurable Serial Peripheral Interface (CSPI/eCSPI) for i.MX
+
+maintainers:
+ - Shawn Guo <shawn.guo@xxxxxxxxxx>
+
+allOf:
+ - $ref: "/schemas/spi/spi-controller.yaml#"
+
+properties:
+ compatible:
+ oneOf:
+ - const: fsl,imx1-cspi
+ - const: fsl,imx21-cspi
+ - const: fsl,imx27-cspi
+ - const: fsl,imx31-cspi
+ - const: fsl,imx35-cspi
+ - const: fsl,imx51-ecspi
+ - const: fsl,imx53-ecspi
+ - items:
+ - enum:
+ - fsl,imx50-ecspi
+ - fsl,imx6q-ecspi
+ - fsl,imx6sx-ecspi
+ - fsl,imx6sl-ecspi
+ - fsl,imx6sll-ecspi
+ - fsl,imx6ul-ecspi
+ - fsl,imx7d-ecspi
+ - fsl,imx8mq-ecspi
+ - fsl,imx8mm-ecspi
+ - fsl,imx8mn-ecspi
+ - fsl,imx8mp-ecspi
+ - const: fsl,imx51-ecspi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: SoC SPI ipg clock
+ - description: SoC SPI per clock
+
+ clock-names:
+ items:
+ - const: ipg
+ - const: per
+
+ dmas:
+ items:
+ - description: DMA controller phandle and request line for RX
+ - description: DMA controller phandle and request line for TX
+
+ dma-names:
+ items:
+ - const: rx
+ - const: tx
+
+ fsl,spi-rdy-drctl:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Integer, representing the value of DRCTL, the register controlling
+ the SPI_READY handling. Note that to enable the DRCTL consideration,
+ the SPI_READY mode-flag needs to be set too.
+ Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst).
+ enum: [0, 1, 2]
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx5-clock.h>
+
+ spi@70010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx51-ecspi";
+ reg = <0x70010000 0x4000>;
+ interrupts = <36>;
+ clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>,
+ <&clks IMX5_CLK_ECSPI1_PER_GATE>;
+ clock-names = "ipg", "per";
+ };
--
2.7.4