[PATCH v3 3/3] phy: omap-usb2-phy: disable PHY charger detect

[Roger Quadros]

AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs.  Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.

Using property "ti,disable-charger-det" in the DT usb2-phy node to
enable this workaround for AM654x PG1.0.

This addresses Silicon Errata:
i2075 - "USB2PHY: USB2PHY Charger Detect is Enabled by Default Without VBUS
Presence"

Signed-off-by: Bin Liu <b-liu@xxxxxx>
Signed-off-by: Sekhar Nori <nsekhar@xxxxxx>
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
---
 drivers/phy/ti/phy-omap-usb2.c | 35 +++++++++++++++++++++++++++-------
 1 file changed, 28 insertions(+), 7 deletions(-)

diff --git a/drivers/phy/ti/phy-omap-usb2.c b/drivers/phy/ti/phy-omap-usb2.c
index cb2dd3230fa7..21c3904d4efc 100644
--- a/drivers/phy/ti/phy-omap-usb2.c
+++ b/drivers/phy/ti/phy-omap-usb2.c
@@ -26,6 +26,10 @@
 #define USB2PHY_ANA_CONFIG1		0x4c
 #define USB2PHY_DISCON_BYP_LATCH	BIT(31)
 
+#define USB2PHY_CHRG_DET			0x14
+#define USB2PHY_CHRG_DET_USE_CHG_DET_REG	BIT(29)
+#define USB2PHY_CHRG_DET_DIS_CHG_DET		BIT(28)
+
 /* SoC Specific USB2_OTG register definitions */
 #define AM654_USB2_OTG_PD		BIT(8)
 #define AM654_USB2_VBUS_DET_EN		BIT(5)
@@ -43,6 +47,7 @@
 #define OMAP_USB2_HAS_START_SRP			BIT(0)
 #define OMAP_USB2_HAS_SET_VBUS			BIT(1)
 #define OMAP_USB2_CALIBRATE_FALSE_DISCONNECT	BIT(2)
+#define OMAP_USB2_DISABLE_CHRG_DET		BIT(3)
 
 struct omap_usb {
 	struct usb_phy		phy;
@@ -236,6 +241,13 @@ static int omap_usb_init(struct phy *x)
 		omap_usb_writel(phy->phy_base, USB2PHY_ANA_CONFIG1, val);
 	}
 
+	if (phy->flags & OMAP_USB2_DISABLE_CHRG_DET) {
+		val = omap_usb_readl(phy->phy_base, USB2PHY_CHRG_DET);
+		val |= USB2PHY_CHRG_DET_USE_CHG_DET_REG |
+		       USB2PHY_CHRG_DET_DIS_CHG_DET;
+		omap_usb_writel(phy->phy_base, USB2PHY_CHRG_DET, val);
+	}
+
 	return 0;
 }
 
@@ -366,14 +378,12 @@ static int omap_usb2_probe(struct platform_device *pdev)
 	phy->mask		= phy_data->mask;
 	phy->power_on		= phy_data->power_on;
 	phy->power_off		= phy_data->power_off;
+	phy->flags		= phy_data->flags;
 
-	if (phy_data->flags & OMAP_USB2_CALIBRATE_FALSE_DISCONNECT) {
-		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		phy->phy_base = devm_ioremap_resource(&pdev->dev, res);
-		if (IS_ERR(phy->phy_base))
-			return PTR_ERR(phy->phy_base);
-		phy->flags |= OMAP_USB2_CALIBRATE_FALSE_DISCONNECT;
-	}
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	phy->phy_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(phy->phy_base))
+		return PTR_ERR(phy->phy_base);
 
 	phy->syscon_phy_power = syscon_regmap_lookup_by_phandle(node,
 							"syscon-phy-power");
@@ -405,6 +415,17 @@ static int omap_usb2_probe(struct platform_device *pdev)
 		}
 	}
 
+	/*
+	 * Errata i2075: USB2PHY: USB2PHY Charger Detect is Enabled by
+	 * Default Without VBUS Presence.
+	 *
+	 * AM654x SR1.0 has a silicon bug due to which D+ is pulled high after
+	 * POR, which could cause enumeration failure with some USB hubs.
+	 * Disabling the USB2_PHY Charger Detect function will put D+
+	 * into the normal state.
+	 */
+	if (of_property_read_bool(node, "ti,disable-charger-det"))
+		phy->flags |= OMAP_USB2_DISABLE_CHRG_DET;
 
 	phy->wkupclk = devm_clk_get(phy->dev, "wkupclk");
 	if (IS_ERR(phy->wkupclk)) {
-- 
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki