Re: [PATCH v14 4/4] power: supply: bq25150 introduce the bq25150

From: Sebastian Reichel
Date: Tue Jun 30 2020 - 19:33:48 EST

Next message: Peter Xu: "Re: [PATCH v4 00/26] mm: Page fault accounting cleanups"
Previous message: Matthias Kaehlcke: "Re: [PATCH 1/4] arm64: dts: sdm845: Add OPP table for all qup devices"
In reply to: Ricardo Rivera-Matos: "[PATCH v14 4/4] power: supply: bq25150 introduce the bq25150"
Next in thread: Ricardo Rivera-Matos: "[PATCH v14 1/4] power_supply: Add additional health properties to the header"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi,

On Tue, Jun 30, 2020 at 04:54:26PM -0500, Ricardo Rivera-Matos wrote:
> Introduce the bq2515x family of chargers.
>
> The BQ2515X family of devices are highly integrated battery management
> ICs that integrate the most common functions for wearable devices
> namely a charger, an output voltage rail, ADC for battery and system
> monitoring, and a push-button controller.
>
> Datasheets:
> bq25150 - http://www.ti.com/lit/ds/symlink/bq25150.pdf
> bq25155 - http://www.ti.com/lit/ds/symlink/bq25155.pdf
>
> Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@xxxxxx>
> ---
> drivers/power/supply/Kconfig | 13 +
> drivers/power/supply/Makefile | 1 +
> drivers/power/supply/bq2515x_charger.c | 1158 ++++++++++++++++++++++++
> 3 files changed, 1172 insertions(+)
> create mode 100644 drivers/power/supply/bq2515x_charger.c
>
> diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
> index 44d3c8512fb8..faf2830aa152 100644
> --- a/drivers/power/supply/Kconfig
> +++ b/drivers/power/supply/Kconfig
> @@ -610,6 +610,19 @@ config CHARGER_BQ24735
> help
> Say Y to enable support for the TI BQ24735 battery charger.
>
> +config CHARGER_BQ2515X
> + tristate "TI BQ2515X battery charger family"
> + depends on I2C
> + depends on GPIOLIB || COMPILE_TEST
> + select REGMAP_I2C
> + help
> + Say Y to enable support for the TI BQ2515X family of battery
> + charging integrated circuits. The BQ2515X are highly integrated
> + battery charge management ICs that integrate the most common
> + functions for wearable devices, namely a charger, an output voltage
> + rail, ADC for battery and system monitoring, and push-button
> + controller.
> +
> config CHARGER_BQ25890
> tristate "TI BQ25890 battery charger driver"
> depends on I2C
> diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
> index b9644663e435..b3c694a65114 100644
> --- a/drivers/power/supply/Makefile
> +++ b/drivers/power/supply/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_CHARGER_BQ2415X) += bq2415x_charger.o
> obj-$(CONFIG_CHARGER_BQ24190) += bq24190_charger.o
> obj-$(CONFIG_CHARGER_BQ24257) += bq24257_charger.o
> obj-$(CONFIG_CHARGER_BQ24735) += bq24735-charger.o
> +obj-$(CONFIG_CHARGER_BQ2515X) += bq2515x_charger.o
> obj-$(CONFIG_CHARGER_BQ25890) += bq25890_charger.o
> obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o
> obj-$(CONFIG_CHARGER_TPS65090) += tps65090-charger.o
> diff --git a/drivers/power/supply/bq2515x_charger.c b/drivers/power/supply/bq2515x_charger.c
> new file mode 100644
> index 000000000000..f386484b5035
> --- /dev/null
> +++ b/drivers/power/supply/bq2515x_charger.c
> @@ -0,0 +1,1158 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// BQ2515X Battery Charger Driver
> +// Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/power_supply.h>
> +#include <linux/regmap.h>
> +#include <linux/types.h>
> +
> +#define BQ2515X_MANUFACTURER "Texas Instruments"
> +
> +#define BQ2515X_STAT0 0x00
> +#define BQ2515X_STAT1 0x01
> +#define BQ2515X_STAT2 0x02
> +#define BQ2515X_FLAG0 0x03
> +#define BQ2515X_FLAG1 0x04
> +#define BQ2515X_FLAG2 0x05
> +#define BQ2515X_FLAG3 0x06
> +#define BQ2515X_MASK0 0x07
> +#define BQ2515X_MASK1 0x08
> +#define BQ2515X_MASK2 0x09
> +#define BQ2515X_MASK3 0x0a
> +#define BQ2515X_VBAT_CTRL 0x12
> +#define BQ2515X_ICHG_CTRL 0x13
> +#define BQ2515X_PCHRGCTRL 0x14
> +#define BQ2515X_TERMCTRL 0x15
> +#define BQ2515X_BUVLO 0x16
> +#define BQ2515X_CHARGERCTRL0 0x17
> +#define BQ2515X_CHARGERCTRL1 0x18
> +#define BQ2515X_ILIMCTRL 0x19
> +#define BQ2515X_LDOCTRL 0x1d
> +#define BQ2515X_MRCTRL 0x30
> +#define BQ2515X_ICCTRL0 0x35
> +#define BQ2515X_ICCTRL1 0x36
> +#define BQ2515X_ICCTRL2 0x37
> +#define BQ2515X_ADCCTRL0 0x40
> +#define BQ2515X_ADCCTRL1 0x41
> +#define BQ2515X_ADC_VBAT_M 0x42
> +#define BQ2515X_ADC_VBAT_L 0x43
> +#define BQ2515X_ADC_TS_M 0x44
> +#define BQ2515X_ADC_TS_L 0x45
> +#define BQ2515X_ADC_ICHG_M 0x46
> +#define BQ2515X_ADC_ICHG_L 0x47
> +#define BQ2515X_ADC_ADCIN_M 0x48
> +#define BQ2515X_ADC_ADCIN_L 0x49
> +#define BQ2515X_ADC_VIN_M 0x4a
> +#define BQ2515X_ADC_VIN_L 0x4b
> +#define BQ2515X_ADC_PMID_M 0x4c
> +#define BQ2515X_ADC_PMID_L 0x4d
> +#define BQ2515X_ADC_IIN_M 0x4e
> +#define BQ2515X_ADC_IIN_L 0x4f
> +#define BQ2515X_ADC_COMP1_M 0x52
> +#define BQ2515X_ADC_COMP1_L 0X53
> +#define BQ2515X_ADC_COMP2_M 0X54
> +#define BQ2515X_ADC_COMP2_L 0x55
> +#define BQ2515X_ADC_COMP3_M 0x56
> +#define BQ2515X_ADC_COMP3_L 0x57
> +#define BQ2515X_ADC_READ_EN 0x58
> +#define BQ2515X_TS_FASTCHGCTRL 0x61
> +#define BQ2515X_TS_COLD 0x62
> +#define BQ2515X_TS_COOL 0x63
> +#define BQ2515X_TS_WARM 0x64
> +#define BQ2515X_TS_HOT 0x65
> +#define BQ2515X_DEVICE_ID 0x6f
> +
> +#define BQ2515X_DEFAULT_ICHG_UA 10000
> +#define BQ25150_DEFAULT_ILIM_UA 100000
> +#define BQ25155_DEFAULT_ILIM_UA 500000
> +#define BQ2515X_DEFAULT_VBAT_REG_UV 4200000
> +#define BQ2515X_DEFAULT_IPRECHARGE_UA 2500
> +
> +#define BQ2515X_DIVISOR 65536
> +#define BQ2515X_VBAT_BASE_VOLT 3600000
> +#define BQ2515X_VBAT_REG_MAX 4600000
> +#define BQ2515X_VBAT_REG_MIN 3600000
> +#define BQ2515X_VBAT_STEP_UV 10000
> +#define BQ2515X_UV_FACTOR 1000000
> +#define BQ2515X_VBAT_MULTIPLIER 6
> +#define BQ2515X_ICHG_DIVISOR 52429
> +#define BQ2515X_ICHG_CURR_STEP_THRESH_UA 318750
> +#define BQ2515X_ICHG_MIN_UA 0
> +#define BQ2515X_ICHG_MAX_UA 500000
> +#define BQ2515X_ICHG_RNG_1B0_UA 1250
> +#define BQ2515X_ICHG_RNG_1B1_UA 2500
> +#define BQ2515X_VLOWV_SEL_1B0_UV 3000000
> +#define BQ2515X_VLOWV_SEL_1B1_UV 2800000
> +#define BQ2515X_PRECHRG_ICHRG_RNGE_1875_UA 18750
> +#define BQ2515X_PRECHRG_ICHRG_RNGE_3750_UA 37500
> +#define BQ2515X_TWAKE2_MIN_US 1700000
> +#define BQ2515X_TWAKE2_MAX_US 2300000
> +
> +#define BQ2515X_ILIM_150MA 0x2
> +#define BQ2515X_ILIM_MASK 0x7
> +#define BQ2515X_ILIM_MIN 50000
> +#define BQ2515X_ILIM_MAX 600000
> +#define BQ2515X_HEALTH_MASK 0xf
> +#define BQ2515X_ICHGRNG_MASK 0x80
> +#define BQ2515X_STAT0_MASK 0x0f
> +#define BQ2515X_STAT1_MASK 0x1f
> +#define BQ2515X_PRECHARGE_MASK 0x1f
> +
> +#define BQ2515X_TS_HOT_STAT BIT(0)
> +#define BQ2515X_TS_WARM_STAT BIT(1)
> +#define BQ2515X_TS_COOL_STAT BIT(2)
> +#define BQ2515X_TS_COLD_STAT BIT(3)
> +#define BQ2515X_SAFETY_TIMER_EXP BIT(5)
> +
> +#define BQ2515X_EN_VBAT_READ BIT(3)
> +#define BQ2515X_EN_ICHG_READ BIT(5)
> +
> +#define BQ2515X_VIN_GOOD BIT(0)
> +#define BQ2515X_CHRG_DONE BIT(5)
> +#define BQ2515X_CV_CHRG_MODE BIT(6)
> +
> +#define BQ2515X_VIN_OVP_FAULT_STAT BIT(7)
> +
> +#define BQ2515X_WATCHDOG_DISABLE BIT(4)
> +
> +#define BQ2515X_ICHARGE_RANGE BIT(7)
> +
> +#define BQ2515X_VLOWV_SEL BIT(5)
> +
> +#define BQ2515X_CHARGER_DISABLE BIT(0)
> +
> +#define BQ2515X_HWRESET_14S_WD BIT(1)
> +
> +static const int bq2515x_ilim_lvl_values[] = {
> + 50000, 100000, 150000, 200000, 300000, 400000, 500000, 600000
> +};
> +
> +/**
> + * struct bq2515x_init_data -
> + * @ilim: input current limit
> + */
> +struct bq2515x_init_data {
> + int ilim;
> +};
> +
> +enum bq2515x_id {
> + BQ25150,
> + BQ25155,
> +};
> +
> +/**
> + * struct bq2515x_device -
> + * @mains: mains properties
> + * @battery: battery properties
> + * @regmap: register map structure
> + * @dev: device structure
> + *
> + * @reset_gpio: manual reset (MR) pin
> + * @powerdown_gpio: low power mode pin
> + * @ac_detect_gpio: power good (PG) pin
> + * @ce_gpio: charge enable (CE) pin
> + *
> + * @model_name: string value describing device model
> + * @device_id: value of device_id
> + * @mains_online: boolean value indicating power supply online
> + *
> + * @bq2515x_init_data init_data: charger initialization data structure
> + */
> +struct bq2515x_device {
> + struct power_supply *mains;
> + struct power_supply *battery;
> + struct regmap *regmap;
> + struct device *dev;
> +
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *powerdown_gpio;
> + struct gpio_desc *ac_detect_gpio;
> + struct gpio_desc *ce_gpio;
> +
> + char model_name[I2C_NAME_SIZE];
> + int device_id;
> + bool mains_online;
> +
> + struct bq2515x_init_data init_data;
> +};
> +
> +static struct reg_default bq25150_reg_defaults[] = {
> + {BQ2515X_FLAG0, 0x0},
> + {BQ2515X_FLAG1, 0x0},
> + {BQ2515X_FLAG2, 0x0},
> + {BQ2515X_FLAG3, 0x0},
> + {BQ2515X_MASK0, 0x0},
> + {BQ2515X_MASK1, 0x0},
> + {BQ2515X_MASK2, 0x71},
> + {BQ2515X_MASK3, 0x0},
> + {BQ2515X_VBAT_CTRL, 0x3C},
> + {BQ2515X_ICHG_CTRL, 0x8},
> + {BQ2515X_PCHRGCTRL, 0x2},
> + {BQ2515X_TERMCTRL, 0x14},
> + {BQ2515X_BUVLO, 0x0},
> + {BQ2515X_CHARGERCTRL0, 0x82},
> + {BQ2515X_CHARGERCTRL1, 0x42},
> + {BQ2515X_ILIMCTRL, 0x1},
> + {BQ2515X_LDOCTRL, 0xB0},
> + {BQ2515X_MRCTRL, 0x2A},
> + {BQ2515X_ICCTRL0, 0x10},
> + {BQ2515X_ICCTRL1, 0x0},
> + {BQ2515X_ICCTRL2, 0x0},
> + {BQ2515X_ADCCTRL0, 0x2},
> + {BQ2515X_ADCCTRL1, 0x40},
> + {BQ2515X_ADC_COMP1_M, 0x23},
> + {BQ2515X_ADC_COMP1_L, 0x20},
> + {BQ2515X_ADC_COMP2_M, 0x38},
> + {BQ2515X_ADC_COMP2_L, 0x90},
> + {BQ2515X_ADC_COMP3_M, 0x0},
> + {BQ2515X_ADC_COMP3_L, 0x0},
> + {BQ2515X_ADC_READ_EN, 0x0},
> + {BQ2515X_TS_FASTCHGCTRL, 0x34},
> + {BQ2515X_TS_COLD, 0x7C},
> + {BQ2515X_TS_COOL, 0x6D},
> + {BQ2515X_TS_WARM, 0x38},
> + {BQ2515X_TS_HOT, 0x27},
> + {BQ2515X_DEVICE_ID, 0x20},
> +};
> +
> +static struct reg_default bq25155_reg_defaults[] = {
> + {BQ2515X_FLAG0, 0x0},
> + {BQ2515X_FLAG1, 0x0},
> + {BQ2515X_FLAG2, 0x0},
> + {BQ2515X_FLAG3, 0x0},
> + {BQ2515X_MASK0, 0x0},
> + {BQ2515X_MASK1, 0x0},
> + {BQ2515X_MASK2, 0x71},
> + {BQ2515X_MASK3, 0x0},
> + {BQ2515X_VBAT_CTRL, 0x3C},
> + {BQ2515X_ICHG_CTRL, 0x8},
> + {BQ2515X_PCHRGCTRL, 0x2},
> + {BQ2515X_TERMCTRL, 0x14},
> + {BQ2515X_BUVLO, 0x0},
> + {BQ2515X_CHARGERCTRL0, 0x82},
> + {BQ2515X_CHARGERCTRL1, 0xC2},
> + {BQ2515X_ILIMCTRL, 0x6},
> + {BQ2515X_LDOCTRL, 0xB0},
> + {BQ2515X_MRCTRL, 0x2A},
> + {BQ2515X_ICCTRL0, 0x10},
> + {BQ2515X_ICCTRL1, 0x0},
> + {BQ2515X_ICCTRL2, 0x40},
> + {BQ2515X_ADCCTRL0, 0x2},
> + {BQ2515X_ADCCTRL1, 0x40},
> + {BQ2515X_ADC_COMP1_M, 0x23},
> + {BQ2515X_ADC_COMP1_L, 0x20},
> + {BQ2515X_ADC_COMP2_M, 0x38},
> + {BQ2515X_ADC_COMP2_L, 0x90},
> + {BQ2515X_ADC_COMP3_M, 0x0},
> + {BQ2515X_ADC_COMP3_L, 0x0},
> + {BQ2515X_ADC_READ_EN, 0x0},
> + {BQ2515X_TS_FASTCHGCTRL, 0x34},
> + {BQ2515X_TS_COLD, 0x7C},
> + {BQ2515X_TS_COOL, 0x6D},
> + {BQ2515X_TS_WARM, 0x38},
> + {BQ2515X_TS_HOT, 0x27},
> + {BQ2515X_DEVICE_ID, 0x35},
> +};
> +
> +static int bq2515x_wake_up(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + int val;
> +
> + /* Read the STAT register if we can read it then the device is out
> + * of ship mode. If the register cannot be read then attempt to wake
> + * it up and enable the ADC.
> + */
> + ret = regmap_read(bq2515x->regmap, BQ2515X_STAT0, &val);
> + if (ret)
> + return ret;
> +
> + /* Need to toggle LP and bring device out of ship mode. The device
> + * will exit the ship mode when the MR pin is held low for at least
> + * t_WAKE2 as shown in section 8.3.7.1 of the datasheet.
> + */
> + gpiod_set_value_cansleep(bq2515x->powerdown_gpio, 0);
> +
> + gpiod_set_value_cansleep(bq2515x->reset_gpio, 0);
> + usleep_range(BQ2515X_TWAKE2_MIN_US, BQ2515X_TWAKE2_MAX_US);
> + gpiod_set_value_cansleep(bq2515x->reset_gpio, 1);
> +
> + return regmap_write(bq2515x->regmap, BQ2515X_ADC_READ_EN,
> + (BQ2515X_EN_VBAT_READ | BQ2515X_EN_ICHG_READ));
> +}
> +
> +static int bq2515x_update_ps_status(struct bq2515x_device *bq2515x)
> +{
> + bool dc = false;
> + unsigned int val;
> + int ret;
> +
> + if (bq2515x->ac_detect_gpio)
> + val = gpiod_get_value_cansleep(bq2515x->ac_detect_gpio);
> + else {
> + ret = regmap_read(bq2515x->regmap, BQ2515X_STAT0, &val);
> + if (ret)
> + return ret;
> + }
> +
> + dc = val & BQ2515X_VIN_GOOD;
> +
> + ret = bq2515x->mains_online != dc;
> +
> + bq2515x->mains_online = dc;
> +
> + return ret;
> +}
> +
> +static int bq2515x_disable_watchdog_timers(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> +
> + ret = regmap_update_bits(bq2515x->regmap, BQ2515X_CHARGERCTRL0,
> + BQ2515X_WATCHDOG_DISABLE, BQ2515X_WATCHDOG_DISABLE);
> + if (ret)
> + return ret;
> +
> + return regmap_update_bits(bq2515x->regmap, BQ2515X_ICCTRL2,
> + BQ2515X_HWRESET_14S_WD, 0);
> +}
> +
> +static int bq2515x_get_battery_voltage_now(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + int vbat_msb;
> + int vbat_lsb;
> + uint32_t vbat_measurement;
> +
> + if (!bq2515x->mains_online)
> + bq2515x_wake_up(bq2515x);
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_VBAT_M, &vbat_msb);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_VBAT_L, &vbat_lsb);
> + if (ret)
> + return ret;
> +
> + vbat_measurement = (vbat_msb << 8) | vbat_lsb;
> +
> + return vbat_measurement * (BQ2515X_UV_FACTOR / BQ2515X_DIVISOR) *
> + BQ2515X_VBAT_MULTIPLIER;
> +}
> +
> +static int bq2515x_get_battery_current_now(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + int ichg_msb;
> + int ichg_lsb;
> + uint32_t ichg_measurement;
> + u16 ichg_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
> + unsigned int ichg_reg_code, reg_code;
> + unsigned int icharge_range = 0, pchrgctrl;
> + unsigned int buvlo, vlowv_sel, vlowv = BQ2515X_VLOWV_SEL_1B0_UV;
> +
> + if (!bq2515x->mains_online)
> + return -ENODATA;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_ICHG_M, &ichg_msb);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ADC_ICHG_L, &ichg_lsb);
> + if (ret)
> + return ret;
> +
> + ichg_measurement = (ichg_msb << 8) | ichg_lsb;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_BUVLO, &buvlo);
> + if (ret)
> + return ret;
> +
> + vlowv_sel = buvlo & BQ2515X_VLOWV_SEL;
> +
> + if (vlowv_sel)
> + vlowv = BQ2515X_VLOWV_SEL_1B1_UV;
> +
> + if (bq2515x_get_battery_voltage_now(bq2515x) < vlowv) {
> + ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL,
> + &pchrgctrl);
> + if (ret)
> + return ret;
> +
> + reg_code = pchrgctrl & BQ2515X_PRECHARGE_MASK;
> + } else {
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ICHG_CTRL,
> + &ichg_reg_code);
> + if (ret)
> + return ret;
> +
> + reg_code = ichg_reg_code;
> + }
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
> + if (ret)
> + return ret;
> +
> + icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
> +
> + if (icharge_range)
> + ichg_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
> +
> + return reg_code * (ichg_multiplier * ichg_measurement /
> + BQ2515X_ICHG_DIVISOR);
> +}
> +
> +static bool bq2515x_get_charge_disable(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + int ce_pin;
> + int icctrl2;
> + int charger_disable;
> +
> + ce_pin = gpiod_get_value_cansleep(bq2515x->ce_gpio);
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ICCTRL2, &icctrl2);
> + if (ret)
> + return ret;
> +
> + charger_disable = icctrl2 & BQ2515X_CHARGER_DISABLE;
> +
> + if (charger_disable || ce_pin)
> + return true;
> +
> + return false;
> +}
> +
> +static int bq2515x_set_charge_disable(struct bq2515x_device *bq2515x, int val)
> +{
> + gpiod_set_value_cansleep(bq2515x->ce_gpio, val);
> +
> + return regmap_update_bits(bq2515x->regmap, BQ2515X_ICCTRL2,
> + BQ2515X_CHARGER_DISABLE, val);
> +}
> +
> +static int bq2515x_get_const_charge_current(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + u16 ichg_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
> + unsigned int ichg_reg_code;
> + unsigned int pchrgctrl;
> + unsigned int icharge_range;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ICHG_CTRL, &ichg_reg_code);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
> + if (ret)
> + return ret;
> +
> + icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
> +
> + if (icharge_range)
> + ichg_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
> +
> + return ichg_reg_code * ichg_multiplier;
> +}
> +
> +static int bq2515x_set_const_charge_current(struct bq2515x_device *bq2515x,
> + int val)
> +{
> + int ret;
> + unsigned int ichg_reg_code;
> + u16 ichg_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
> + unsigned int icharge_range = 0;
> +
> + if (val > BQ2515X_ICHG_MAX_UA || val < BQ2515X_ICHG_MIN_UA)
> + return -EINVAL;
> +
> + if (val > BQ2515X_ICHG_CURR_STEP_THRESH_UA) {
> + ichg_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
> + icharge_range = BQ2515X_ICHARGE_RANGE;
> + }
> +
> + bq2515x_set_charge_disable(bq2515x, 1);
> +
> + ret = regmap_update_bits(bq2515x->regmap, BQ2515X_PCHRGCTRL,
> + BQ2515X_ICHARGE_RANGE, icharge_range);
> + if (ret)
> + return ret;
> +
> + ichg_reg_code = val / ichg_multiplier;
> +
> + ret = regmap_write(bq2515x->regmap, BQ2515X_ICHG_CTRL, ichg_reg_code);
> + if (ret)
> + return ret;
> +
> + return bq2515x_set_charge_disable(bq2515x, 0);
> +}
> +
> +static int bq2515x_get_precharge_current(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + unsigned int pchrgctrl;
> + unsigned int icharge_range;
> + u16 precharge_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
> + unsigned int precharge_reg_code;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
> + if (ret)
> + return ret;
> +
> + icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
> +
> + if (icharge_range)
> + precharge_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
> +
> + precharge_reg_code = pchrgctrl & BQ2515X_PRECHARGE_MASK;
> +
> + return precharge_reg_code * precharge_multiplier;
> +}
> +
> +static int bq2515x_set_precharge_current(struct bq2515x_device *bq2515x,
> + int val)
> +{
> + int ret;
> + unsigned int pchrgctrl;
> + unsigned int icharge_range;
> + unsigned int precharge_reg_code;
> + unsigned int precharge_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
> + unsigned int precharge_max_ua = BQ2515X_PRECHRG_ICHRG_RNGE_1875_UA;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_PCHRGCTRL, &pchrgctrl);
> + if (ret)
> + return ret;
> +
> + icharge_range = pchrgctrl & BQ2515X_ICHARGE_RANGE;
> +
> + if (icharge_range) {
> + precharge_max_ua = BQ2515X_PRECHRG_ICHRG_RNGE_3750_UA;
> + precharge_multiplier = BQ2515X_ICHG_RNG_1B1_UA;
> + } else {
> + precharge_max_ua = BQ2515X_PRECHRG_ICHRG_RNGE_1875_UA;
> + precharge_multiplier = BQ2515X_ICHG_RNG_1B0_UA;
> + }
> + if (val > precharge_max_ua || val < BQ2515X_ICHG_MIN_UA)
> + return -EINVAL;
> +
> + precharge_reg_code = val / precharge_multiplier;
> +
> + ret = bq2515x_set_charge_disable(bq2515x, 1);
> + if (ret)
> + return ret;
> +
> + ret = regmap_update_bits(bq2515x->regmap, BQ2515X_PCHRGCTRL,
> + BQ2515X_PRECHARGE_MASK, precharge_reg_code);
> + if (ret)
> + return ret;
> +
> + return bq2515x_set_charge_disable(bq2515x, 0);
> +}
> +
> +static int bq2515x_charging_status(struct bq2515x_device *bq2515x,
> + union power_supply_propval *val)
> +{
> + bool status0_no_fault;
> + bool status1_no_fault;
> + bool ce_status;
> + bool charge_done;
> + unsigned int status;
> + int ret;
> +
> + if (!bq2515x->mains_online) {
> + val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
> + return 0;
> + }
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_STAT0, &status);
> + if (ret)
> + return ret;
> +
> + /*
> + * The code block below is used to determine if any faults from the
> + * STAT0 register are disbaling charging or if the charge has completed
> + * according to the CHARGE_DONE_STAT bit.
> + */
> + if (((status & BQ2515X_STAT0_MASK) == true) &
> + ((status & BQ2515X_CHRG_DONE) == false)) {
> + status0_no_fault = true;
> + charge_done = false;
> + } else if (status & BQ2515X_CHRG_DONE) {
> + charge_done = true;
> + status0_no_fault = false;
> + } else {
> + status0_no_fault = false;
> + charge_done = false;
> + }
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_STAT1, &status);
> + if (ret)
> + return ret;
> + /*
> + * The code block below is used to determine if any faults from the
> + * STAT1 register are disbaling charging
> + */
> + if ((status & BQ2515X_STAT1_MASK) == false)
> + status1_no_fault = true;
> + else
> + status1_no_fault = false;
> +
> + ce_status = (!bq2515x_get_charge_disable(bq2515x));
> +
> + /*
> + * If there are no faults and charging is enabled, then status is
> + * charging. Otherwise, if charging is complete, then status is full.
> + * Otherwise, if a fault exists or charging is disabled, then status is
> + * not charging
> + */
> + if (status0_no_fault & status1_no_fault & ce_status)
> + val->intval = POWER_SUPPLY_STATUS_CHARGING;
> + else if (charge_done)
> + val->intval = POWER_SUPPLY_STATUS_FULL;
> + else if (!(status0_no_fault & status1_no_fault & ce_status))
> + val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
> +
> + return 0;
> +}
> +
> +static int bq2515x_get_batt_reg(struct bq2515x_device *bq2515x)
> +{
> + int vbat_reg_code;
> + int ret;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_VBAT_CTRL, &vbat_reg_code);
> + if (ret)
> + return ret;
> +
> + return BQ2515X_VBAT_BASE_VOLT + vbat_reg_code * BQ2515X_VBAT_STEP_UV;
> +}
> +
> +static int bq2515x_set_batt_reg(struct bq2515x_device *bq2515x, int val)
> +{
> + int vbat_reg_code;
> +
> + if (val > BQ2515X_VBAT_REG_MAX || val < BQ2515X_VBAT_REG_MIN)
> + return -EINVAL;
> +
> + vbat_reg_code = (val - BQ2515X_VBAT_BASE_VOLT) / BQ2515X_VBAT_STEP_UV;
> +
> + return regmap_write(bq2515x->regmap, BQ2515X_VBAT_CTRL, vbat_reg_code);
> +}
> +
> +static int bq2515x_get_ilim_lvl(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + int ilimctrl;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_ILIMCTRL, &ilimctrl);
> + if (ret)
> + return ret;
> +
> + return bq2515x_ilim_lvl_values[ilimctrl & BQ2515X_ILIM_MASK];
> +}
> +
> +static int bq2515x_set_ilim_lvl(struct bq2515x_device *bq2515x, int val)
> +{
> + int i = 0;
> + unsigned int array_size = ARRAY_SIZE(bq2515x_ilim_lvl_values);
> +
> + for (i = array_size - 1; i > 0; i--) {
> + if (val >= bq2515x_ilim_lvl_values[i])
> + break;
> + }
> + return regmap_write(bq2515x->regmap, BQ2515X_ILIMCTRL, i);
> +}
> +
> +static int bq2515x_power_supply_property_is_writeable(struct power_supply *psy,
> + enum power_supply_property prop)
> +{
> + switch (prop) {
> + case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> + case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static int bq2515x_charger_get_health(struct bq2515x_device *bq2515x,
> + union power_supply_propval *val)
> +{
> + int health = POWER_SUPPLY_HEALTH_GOOD;
> + int ret;
> + unsigned int stat1;
> + unsigned int flag3;
> +
> + if (!bq2515x->mains_online)
> + bq2515x_wake_up(bq2515x);
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_FLAG3, &flag3);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(bq2515x->regmap, BQ2515X_STAT1, &stat1);
> + if (ret)
> + return ret;
> +
> + if (stat1 & BQ2515X_HEALTH_MASK) {
> + switch (stat1 & BQ2515X_HEALTH_MASK) {
> + case BQ2515X_TS_HOT_STAT:
> + health = POWER_SUPPLY_HEALTH_HOT;
> + break;
> + case BQ2515X_TS_WARM_STAT:
> + health = POWER_SUPPLY_HEALTH_WARM;
> + break;
> + case BQ2515X_TS_COOL_STAT:
> + health = POWER_SUPPLY_HEALTH_COOL;
> + break;
> + case BQ2515X_TS_COLD_STAT:
> + health = POWER_SUPPLY_HEALTH_COLD;
> + break;
> + default:
> + health = POWER_SUPPLY_HEALTH_UNKNOWN;
> + break;
> + }
> + }
> +
> + if (stat1 & BQ2515X_VIN_OVP_FAULT_STAT)
> + health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> +
> + if (flag3 & BQ2515X_SAFETY_TIMER_EXP)
> + health = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE;
> +
> + val->intval = health;
> + return 0;
> +}
> +
> +static int bq2515x_mains_set_property(struct power_supply *psy,
> + enum power_supply_property prop,
> + const union power_supply_propval *val)
> +{
> + struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
> + int ret;
> +
> + switch (prop) {
> + case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
> + ret = bq2515x_set_ilim_lvl(bq2515x, val->intval);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int bq2515x_battery_set_property(struct power_supply *psy,
> + enum power_supply_property prop,
> + const union power_supply_propval *val)
> +{
> + struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
> + int ret;
> +
> + switch (prop) {
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
> + ret = bq2515x_set_batt_reg(bq2515x, val->intval);
> + break;
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> + ret = bq2515x_set_const_charge_current(bq2515x, val->intval);
> + break;
> + case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
> + ret = bq2515x_set_precharge_current(bq2515x, val->intval);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return ret;
> +}

Expose those through the charger device. The battery device
can expose maximum data (e.g. POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX),
but should not control the charging itself.

> +static int bq2515x_mains_get_property(struct power_supply *psy,
> + enum power_supply_property prop,
> + union power_supply_propval *val)
> +{
> + struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
> + int ret = 0;
> +
> + switch (prop) {
> + case POWER_SUPPLY_PROP_ONLINE:
> + val->intval = bq2515x->mains_online;
> + break;
> + case POWER_SUPPLY_PROP_HEALTH:
> + ret = bq2515x_charger_get_health(bq2515x, val);
> + if (ret)
> + val->intval = POWER_SUPPLY_HEALTH_UNKNOWN;
> + break;
> + case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
> + ret = bq2515x_get_ilim_lvl(bq2515x);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = ret;
> + break;
> + case POWER_SUPPLY_PROP_MODEL_NAME:
> + val->strval = bq2515x->model_name;
> + break;
> + case POWER_SUPPLY_PROP_MANUFACTURER:
> + val->strval = BQ2515X_MANUFACTURER;
> + break;
> + case POWER_SUPPLY_PROP_STATUS:
> + ret = bq2515x_charging_status(bq2515x, val);
> + if (ret)
> + return ret;
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + return ret;
> +}
> +
> +static int bq2515x_battery_get_property(struct power_supply *psy,
> + enum power_supply_property prop,
> + union power_supply_propval *val)
> +{
> + struct bq2515x_device *bq2515x = power_supply_get_drvdata(psy);
> + int ret;
> +
> + ret = bq2515x_update_ps_status(bq2515x);
> + if (ret)
> + return ret;
> +
> + switch (prop) {
> +
> + case POWER_SUPPLY_PROP_VOLTAGE_NOW:
> + ret = bq2515x_get_battery_voltage_now(bq2515x);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = ret;
> + break;
> + case POWER_SUPPLY_PROP_CURRENT_NOW:
> + ret = bq2515x_get_battery_current_now(bq2515x);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = ret;
> + break;
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> + ret = bq2515x_get_const_charge_current(bq2515x);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = ret;
> + break;
> + case POWER_SUPPLY_PROP_PRECHARGE_CURRENT:
> + ret = bq2515x_get_precharge_current(bq2515x);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = ret;
> + break;
> + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
> + ret = bq2515x_get_batt_reg(bq2515x);
> + if (ret < 0)
> + return ret;
> +
> + val->intval = ret;
> + break;
> + default:
> + return -EINVAL;
> + }
> + return 0;
> +}
> +
> +static enum power_supply_property bq2515x_battery_properties[] = {
> + POWER_SUPPLY_PROP_VOLTAGE_NOW,
> + POWER_SUPPLY_PROP_CURRENT_NOW,
> + POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
> + POWER_SUPPLY_PROP_PRECHARGE_CURRENT,
> + POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
> +};
> +
> +static enum power_supply_property bq2515x_mains_properties[] = {
> + POWER_SUPPLY_PROP_ONLINE,
> + POWER_SUPPLY_PROP_STATUS,
> + POWER_SUPPLY_PROP_HEALTH,
> + POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
> + POWER_SUPPLY_PROP_MODEL_NAME,
> + POWER_SUPPLY_PROP_MANUFACTURER,
> +};
> +
> +static struct power_supply_desc bq2515x_mains_desc = {
> + .name = "bq2515x-mains",
> + .type = POWER_SUPPLY_TYPE_MAINS,
> + .get_property = bq2515x_mains_get_property,
> + .set_property = bq2515x_mains_set_property,
> + .properties = bq2515x_mains_properties,
> + .num_properties = ARRAY_SIZE(bq2515x_mains_properties),
> + .property_is_writeable = bq2515x_power_supply_property_is_writeable,
> +};
> +
> +static struct power_supply_desc bq2515x_battery_desc = {
> + .name = "bq2515x-battery",
> + .type = POWER_SUPPLY_TYPE_BATTERY,
> + .get_property = bq2515x_battery_get_property,
> + .set_property = bq2515x_battery_set_property,
> + .properties = bq2515x_battery_properties,
> + .num_properties = ARRAY_SIZE(bq2515x_battery_properties),
> + .property_is_writeable = bq2515x_power_supply_property_is_writeable,
> +};
> +
> +static int bq2515x_power_supply_register(struct bq2515x_device *bq2515x,
> + struct device *dev, struct power_supply_config psy_cfg)
> +{
> + bq2515x->mains = devm_power_supply_register(bq2515x->dev,
> + &bq2515x_mains_desc,
> + &psy_cfg);
> + if (IS_ERR(bq2515x->mains))
> + return -EINVAL;
> +
> + bq2515x->battery = devm_power_supply_register(bq2515x->dev,
> + &bq2515x_battery_desc,
> + &psy_cfg);
> + if (IS_ERR(bq2515x->battery))
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static int bq2515x_hw_init(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> + struct power_supply_battery_info bat_info = { };
> +
> + ret = bq2515x_disable_watchdog_timers(bq2515x);
> + if (ret)
> + return ret;
> +
> + if (bq2515x->init_data.ilim) {
> + ret = bq2515x_set_ilim_lvl(bq2515x, bq2515x->init_data.ilim);
> + if (ret)
> + return ret;
> + }
> +
> + ret = power_supply_get_battery_info(bq2515x->mains, &bat_info);
> + if (ret) {
> + dev_warn(bq2515x->dev, "battery info missing, default values will be applied\n");
> +
> + bat_info.constant_charge_current_max_ua =
> + BQ2515X_DEFAULT_ICHG_UA;
> +
> + bat_info.constant_charge_voltage_max_uv =
> + BQ2515X_DEFAULT_VBAT_REG_UV;
> +
> + bat_info.precharge_current_ua =
> + BQ2515X_DEFAULT_IPRECHARGE_UA;
> + }
> +
> + ret = bq2515x_set_const_charge_current(bq2515x,
> + bat_info.constant_charge_current_max_ua);
> + if (ret)
> + return ret;
> +
> + ret = bq2515x_set_batt_reg(bq2515x,
> + bat_info.constant_charge_voltage_max_uv);
> + if (ret)
> + return ret;
> +
> + return bq2515x_set_precharge_current(bq2515x,
> + bat_info.precharge_current_ua);
> +}
> +
> +static int bq2515x_read_properties(struct bq2515x_device *bq2515x)
> +{
> + int ret;
> +
> + ret = device_property_read_u32(bq2515x->dev,
> + "input-current-limit-microamp",
> + &bq2515x->init_data.ilim);
> + if (ret)
> + switch (bq2515x->device_id) {
> + case BQ25150:
> + bq2515x->init_data.ilim = BQ25150_DEFAULT_ILIM_UA;
> + break;
> + case BQ25155:
> + bq2515x->init_data.ilim = BQ25155_DEFAULT_ILIM_UA;
> + break;
> + }

Please add {} for the if.

> + bq2515x->ac_detect_gpio = devm_gpiod_get_optional(bq2515x->dev,
> + "ac-detect", GPIOD_IN);
> + if (IS_ERR(bq2515x->ac_detect_gpio)) {
> + ret = PTR_ERR(bq2515x->ac_detect_gpio);
> + if (ret != -ENODEV) {
> + dev_err(bq2515x->dev, "Failed to get ac detect");
> + return ret;
> + }
> + bq2515x->ac_detect_gpio = NULL;

All of this is not needed. If no GPIO is specified,
devm_gpiod_get_optional() will return NULL instead
of an error code. This is enough:

if (IS_ERR(bq2515x->ac_detect_gpio)) {
ret = PTR_ERR(bq2515x->ac_detect_gpio);
dev_err(bq2515x->dev, "Failed to get ac detect: %d\n", ret);
return ret;
}

> + }
> +
> + bq2515x->reset_gpio = devm_gpiod_get_optional(bq2515x->dev,
> + "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(bq2515x->reset_gpio)) {
> + ret = PTR_ERR(bq2515x->reset_gpio);
> + if (ret != -ENODEV) {
> + dev_err(bq2515x->dev, "Failed to get reset");
> + return ret;
> + }
> + bq2515x->reset_gpio = NULL;
> + }

The same as previous GPIO.

> + bq2515x->powerdown_gpio = devm_gpiod_get_optional(bq2515x->dev,
> + "powerdown", GPIOD_OUT_LOW);
> + if (IS_ERR(bq2515x->powerdown_gpio)) {
> + ret = PTR_ERR(bq2515x->powerdown_gpio);
> + if (ret != -ENODEV) {
> + dev_err(bq2515x->dev, "Failed to get powerdown");
> + return ret;
> + }
> + bq2515x->powerdown_gpio = NULL;
> + }

The same as previous GPIO.

> + bq2515x->ce_gpio = devm_gpiod_get_optional(bq2515x->dev,
> + "charge-enable",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(bq2515x->ce_gpio)) {
> + ret = PTR_ERR(bq2515x->ce_gpio);
> + if (ret != -ENODEV) {
> + dev_err(bq2515x->dev, "Failed to get ce");
> + return ret;
> + }
> + bq2515x->ce_gpio = NULL;
> + }

The same as previous GPIO.

> + return 0;
> +}
> +
> +static bool bq2515x_volatile_register(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case BQ2515X_STAT0 ... BQ2515X_FLAG3:
> + case BQ2515X_ADC_VBAT_M ... BQ2515X_ADC_IIN_L:
> + return true;
> + default:
> + return false;
> + }
> +}
> +
> +static const struct regmap_config bq25150_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> +
> + .max_register = BQ2515X_DEVICE_ID,
> + .reg_defaults = bq25150_reg_defaults,
> + .num_reg_defaults = ARRAY_SIZE(bq25150_reg_defaults),
> + .cache_type = REGCACHE_RBTREE,
> + .volatile_reg = bq2515x_volatile_register,
> +};
> +
> +static const struct regmap_config bq25155_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> +
> + .max_register = BQ2515X_DEVICE_ID,
> + .reg_defaults = bq25155_reg_defaults,
> + .num_reg_defaults = ARRAY_SIZE(bq25155_reg_defaults),
> + .cache_type = REGCACHE_RBTREE,
> + .volatile_reg = bq2515x_volatile_register,
> +};
> +
> +static int bq2515x_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct bq2515x_device *bq2515x;
> + struct power_supply_config charger_cfg = {};
> + int ret;
> +
> + bq2515x = devm_kzalloc(dev, sizeof(*bq2515x), GFP_KERNEL);
> + if (!bq2515x)
> + return -ENOMEM;
> +
> + bq2515x->dev = dev;
> +
> + strncpy(bq2515x->model_name, id->name, I2C_NAME_SIZE);
> +
> + bq2515x->device_id = id->driver_data;
> +
> + switch (bq2515x->device_id) {
> + case BQ25150:
> + bq2515x->regmap = devm_regmap_init_i2c(client,
> + &bq25150_regmap_config);
> + break;
> + case BQ25155:
> + bq2515x->regmap = devm_regmap_init_i2c(client,
> + &bq25155_regmap_config);
> + break;
> + }
> +
> + if (IS_ERR(bq2515x->regmap)) {
> + dev_err(dev, "failed to allocate register map\n");
> + return PTR_ERR(bq2515x->regmap);
> + }
> +
> + i2c_set_clientdata(client, bq2515x);
> +
> + charger_cfg.drv_data = bq2515x;
> + charger_cfg.of_node = dev->of_node;
> +
> + ret = bq2515x_read_properties(bq2515x);
> + if (ret) {
> + dev_err(dev, "Failed to read device tree properties %d\n",
> + ret);
> + return ret;
> + }
> +
> + ret = bq2515x_power_supply_register(bq2515x, dev, charger_cfg);
> + if (ret) {
> + dev_err(dev, "failed to register power supply\n");
> + return ret;
> + }
> +
> + ret = bq2515x_hw_init(bq2515x);
> + if (ret) {
> + dev_err(dev, "Cannot initialize the chip\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id bq2515x_i2c_ids[] = {
> + { "bq25150", BQ25150, },
> + { "bq25155", BQ25155, },
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, bq2515x_i2c_ids);
> +
> +static const struct of_device_id bq2515x_of_match[] = {
> + { .compatible = "ti,bq25150", },
> + { .compatible = "ti,bq25155", },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, bq2515x_of_match);
> +
> +static struct i2c_driver bq2515x_driver = {
> + .driver = {
> + .name = "bq2515x-charger",
> + .of_match_table = bq2515x_of_match,
> + },
> + .probe = bq2515x_probe,
> + .id_table = bq2515x_i2c_ids,
> +};
> +module_i2c_driver(bq2515x_driver);
> +
> +MODULE_AUTHOR("Dan Murphy <dmurphy@xxxxxx>");
> +MODULE_AUTHOR("Ricardo Rivera-Matos <r-rivera-matos@xxxxxx>");
> +MODULE_DESCRIPTION("BQ2515X charger driver");
> +MODULE_LICENSE("GPL v2");

Otherwise this looks good to me now. I hope I can merge the next
version :)

-- Sebastian

Attachment: signature.asc
Description: PGP signature

Next message: Peter Xu: "Re: [PATCH v4 00/26] mm: Page fault accounting cleanups"
Previous message: Matthias Kaehlcke: "Re: [PATCH 1/4] arm64: dts: sdm845: Add OPP table for all qup devices"
In reply to: Ricardo Rivera-Matos: "[PATCH v14 4/4] power: supply: bq25150 introduce the bq25150"
Next in thread: Ricardo Rivera-Matos: "[PATCH v14 1/4] power_supply: Add additional health properties to the header"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]