[PATCH v1 10/15] scsi: pm_8001: use generic power management

[Vaibhav Gupta]

With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.

After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.

The driver was calling pci_save/restore_state(), pci_choose_state(),
pci_enable/disable_device() and pci_set_power_state() which is no more
needed.

Compile-tested only.

Signed-off-by: Vaibhav Gupta <vaibhavgupta40@xxxxxxxxx>
---
 drivers/scsi/pm8001/pm8001_init.c | 43 ++++++++++++-------------------
 1 file changed, 16 insertions(+), 27 deletions(-)

diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c
index 9e99262a2b9d..6831760fca59 100644
--- a/drivers/scsi/pm8001/pm8001_init.c
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -1178,23 +1178,22 @@ static void pm8001_pci_remove(struct pci_dev *pdev)
 
 /**
  * pm8001_pci_suspend - power management suspend main entry point
- * @pdev: PCI device struct
- * @state: PM state change to (usually PCI_D3)
+ * @dev: Device struct
  *
  * Returns 0 success, anything else error.
  */
-static int pm8001_pci_suspend(struct pci_dev *pdev, pm_message_t state)
+static int __maybe_unused pm8001_pci_suspend(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct sas_ha_struct *sha = pci_get_drvdata(pdev);
 	struct pm8001_hba_info *pm8001_ha;
 	int  i, j;
-	u32 device_state;
 	pm8001_ha = sha->lldd_ha;
 	sas_suspend_ha(sha);
 	flush_workqueue(pm8001_wq);
 	scsi_block_requests(pm8001_ha->shost);
 	if (!pdev->pm_cap) {
-		dev_err(&pdev->dev, " PCI PM not supported\n");
+		dev_err(dev, " PCI PM not supported\n");
 		return -ENODEV;
 	}
 	PM8001_CHIP_DISP->interrupt_disable(pm8001_ha, 0xFF);
@@ -1217,24 +1216,21 @@ static int pm8001_pci_suspend(struct pci_dev *pdev, pm_message_t state)
 		for (j = 0; j < PM8001_MAX_MSIX_VEC; j++)
 			tasklet_kill(&pm8001_ha->tasklet[j]);
 #endif
-	device_state = pci_choose_state(pdev, state);
 	pm8001_printk("pdev=0x%p, slot=%s, entering "
-		      "operating state [D%d]\n", pdev,
-		      pm8001_ha->name, device_state);
-	pci_save_state(pdev);
-	pci_disable_device(pdev);
-	pci_set_power_state(pdev, device_state);
+		      "suspended state\n", pdev,
+		      pm8001_ha->name);
 	return 0;
 }
 
 /**
  * pm8001_pci_resume - power management resume main entry point
- * @pdev: PCI device struct
+ * @dev: Device struct
  *
  * Returns 0 success, anything else error.
  */
-static int pm8001_pci_resume(struct pci_dev *pdev)
+static int __maybe_unused pm8001_pci_resume(struct device *dev)
 {
+	struct pci_dev *pdev = to_pci_dev(dev);
 	struct sas_ha_struct *sha = pci_get_drvdata(pdev);
 	struct pm8001_hba_info *pm8001_ha;
 	int rc;
@@ -1247,17 +1243,8 @@ static int pm8001_pci_resume(struct pci_dev *pdev)
 	pm8001_printk("pdev=0x%p, slot=%s, resuming from previous "
 		"operating state [D%d]\n", pdev, pm8001_ha->name, device_state);
 
-	pci_set_power_state(pdev, PCI_D0);
-	pci_enable_wake(pdev, PCI_D0, 0);
-	pci_restore_state(pdev);
-	rc = pci_enable_device(pdev);
-	if (rc) {
-		pm8001_printk("slot=%s Enable device failed during resume\n",
-			      pm8001_ha->name);
-		goto err_out_enable;
-	}
+	device_wakeup_disable(dev);
 
-	pci_set_master(pdev);
 	rc = pci_go_44(pdev);
 	if (rc)
 		goto err_out_disable;
@@ -1318,8 +1305,7 @@ static int pm8001_pci_resume(struct pci_dev *pdev)
 
 err_out_disable:
 	scsi_remove_host(pm8001_ha->shost);
-	pci_disable_device(pdev);
-err_out_enable:
+
 	return rc;
 }
 
@@ -1402,13 +1388,16 @@ static struct pci_device_id pm8001_pci_table[] = {
 	{} /* terminate list */
 };
 
+static SIMPLE_DEV_PM_OPS(pm8001_pci_pm_ops,
+			 pm8001_pci_suspend,
+			 pm8001_pci_resume);
+
 static struct pci_driver pm8001_pci_driver = {
 	.name		= DRV_NAME,
 	.id_table	= pm8001_pci_table,
 	.probe		= pm8001_pci_probe,
 	.remove		= pm8001_pci_remove,
-	.suspend	= pm8001_pci_suspend,
-	.resume		= pm8001_pci_resume,
+	.driver.pm	= &pm8001_pci_pm_ops,
 };
 
 /**
-- 
2.27.0