RE: [PATCH v5 3/3] fpga: dfl: add support for N3000 Nios private feature

From: Wu, Hao
Date: Thu Aug 13 2020 - 04:56:12 EST

Next message: Anup Patel: "Re: [PATCH v5 3/9] RISC-V: Implement late mapping page table allocation functions"
Previous message: Stanley Chu: "Re: [PATCH v7] scsi: ufs: Quiesce all scsi devices before shutdown"
In reply to: Xu Yilun: "[PATCH v5 3/3] fpga: dfl: add support for N3000 Nios private feature"
Next in thread: Xu Yilun: "Re: [PATCH v5 3/3] fpga: dfl: add support for N3000 Nios private feature"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

> Subject: [PATCH v5 3/3] fpga: dfl: add support for N3000 Nios private feature
>
> This patch adds support for the Nios handshake private feature on Intel
> PAC (Programmable Acceleration Card) N3000.
>
> The Nios is the embedded processor on the FPGA card. This private feature
> provides a handshake interface to FPGA Nois firmware, which receives
> retimer configuration command from host and executes via an internal SPI
> master (spi-altera). When Nios finishes the configuration, host takes over
> the ownership of the SPI master to control an Intel MAX10 BMC (Board
> Management Controller) Chip on the SPI bus.
>
> For Nios firmware handshake part, this driver requests the retimer
> configuration for Nios with parameters from module param, and adds some
> sysfs nodes for user to query the onboard retimer's working mode and
> Nios firmware version.
>
> For SPI part, this driver adds a spi-altera platform device as well as
> the MAX10 BMC spi slave info. A spi-altera driver will be matched to
> handle the following SPI work.
>
> Signed-off-by: Xu Yilun <yilun.xu@xxxxxxxxx>
> Signed-off-by: Wu Hao <hao.wu@xxxxxxxxx>
> Signed-off-by: Matthew Gerlach <matthew.gerlach@xxxxxxxxxxxxxxx>
> Signed-off-by: Russ Weight <russell.h.weight@xxxxxxxxx>
> Reviewed-by: Tom Rix <trix@xxxxxxxxxx>
> ---
> v3: Add the doc for this driver
> Minor fixes for comments from Tom
> v4: Move the err log in regmap implementation, and delete
> n3000_nios_writel/readl(), they have nothing to wrapper now.
> Some minor fixes and comments improvement.
> v5: Fix the output of fec_mode sysfs inf to "no" on 10G configuration,
> cause no FEC mode could be configured for 10G.
> Rename the dfl_n3000_nios_* to n3000_nios_*
> Improves comments.
> ---
> .../ABI/testing/sysfs-bus-dfl-devices-n3000-nios | 18 +
> Documentation/fpga/dfl-n3000-nios.rst | 45 ++
> Documentation/fpga/index.rst | 1 +
> drivers/fpga/Kconfig | 11 +
> drivers/fpga/Makefile | 2 +
> drivers/fpga/dfl-n3000-nios.c | 528 +++++++++++++++++++++
> 6 files changed, 605 insertions(+)
> create mode 100644 Documentation/ABI/testing/sysfs-bus-dfl-devices-
> n3000-nios
> create mode 100644 Documentation/fpga/dfl-n3000-nios.rst
> create mode 100644 drivers/fpga/dfl-n3000-nios.c
>
> diff --git a/Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios
> b/Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios
> new file mode 100644
> index 0000000..221d635
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-bus-dfl-devices-n3000-nios
> @@ -0,0 +1,18 @@
> +What: /sys/bus/dfl/devices/dfl_dev.X/fec_mode
> +Date: Aug 2020
> +KernelVersion: 5.10
> +Contact: Xu Yilun <yilun.xu@xxxxxxxxx>
> +Description: Read-only. It returns the FEC mode of the ethernet retimer
> + configured by NIOS firmware. "rs" for Reed Solomon FEC,
> "kr"
> + for Fire Code FEC, "no" FOR NO FEC. The FEC mode could be
> set
> + by module parameters, but it could only be set once after the
> + board powers up.
> + Format: string
> +
> +What: /sys/bus/dfl/devices/dfl_dev.X/nios_fw_version
> +Date: Aug 2020
> +KernelVersion: 5.10
> +Contact: Xu Yilun <yilun.xu@xxxxxxxxx>
> +Description: Read-only. It returns the NIOS firmware version in FPGA. Its
> + format is "major.minor.patch".
> + Format: %x.%x.%x
> diff --git a/Documentation/fpga/dfl-n3000-nios.rst
> b/Documentation/fpga/dfl-n3000-nios.rst
> new file mode 100644
> index 0000000..c562aab
> --- /dev/null
> +++ b/Documentation/fpga/dfl-n3000-nios.rst
> @@ -0,0 +1,45 @@
> +.. SPDX-License-Identifier: GPL-2.0
> +
> +=================================
> +N3000 Nios Private Feature Driver
> +=================================
> +
> +The N3000 Nios driver supports for the Nios handshake private feature on
> Intel
> +PAC (Programmable Acceleration Card) N3000.
> +
> +The Nios is the embedded processor on the FPGA card. This private feature
> +provides a handshake interface to FPGA Nios firmware, which receives the
> +ethernet retimer configuration command from host and does the
> configuration via
> +an internal SPI master (spi-altera). When Nios finishes the configuration,
> host
> +takes over the ownership of the SPI master to control an Intel MAX10 BMC
> (Board
> +Management Controller) Chip on the SPI bus.
> +
> +So the driver does 2 major tasks on probe, uses the Nios firmware to
> configure
> +the ethernet retimer, and then creates a spi master platform device with
> the
> +MAX10 device info in spi_board_info.
> +
> +Module Parameters
> +=================
> +
> +The N3000 Nios driver supports the following module parameters:
> +
> +* fec_mode: string
> + Require the Nios firmware to set the FEC (Forward Error Correction) mode
> of
> + the ethernet retimer on the Intel PAC N3000. The possible values could be:
> +
> + - "rs": Reed Solomon FEC (default)
> + - "kr": Fire Code FEC
> + - "no": No FEC
> +
> + The configuration can only be set once after the board powers up, the
> + firmware will not accept second configuration afterward. So it is not
> proper
> + to have a RW sysfs node for the FEC mode. A better way is that we set the
> FEC
> + mode on driver probe according to the module parameter from user, and
> create
> + a RO sysfs node for the FEC mode query.
> +
> + Besides, the fec mode will not be changed if the module is reloaded with a
> + different param value.

And it won't work on hardware doesn't support this feature, e.g. 10G based
Hardware as you mentioned.

And to be clear, it's better to mention that, on N3000, there are 2 retimer chips,
each chip supports 4 links, which matches the code below, It configures all links
of the retimers to the same FEC mode.

> +
> + The configured value of the fec mode could be queried from sysfs node:
> +
> + /sys/bus/dfl/devices/dfl_dev.X/fec_mode
> diff --git a/Documentation/fpga/index.rst b/Documentation/fpga/index.rst
> index f80f956..5fd3c37 100644
> --- a/Documentation/fpga/index.rst
> +++ b/Documentation/fpga/index.rst
> @@ -8,6 +8,7 @@ fpga
> :maxdepth: 1
>
> dfl
> + dfl-n3000-nios
>
> .. only:: subproject and html
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 7cd5a29..f6252cd 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -191,6 +191,17 @@ config FPGA_DFL_AFU
> to the FPGA infrastructure via a Port. There may be more than one
> Port/AFU per DFL based FPGA device.
>
> +config FPGA_DFL_N3000_NIOS

FPGA_DFL_NIOS_INTEL_PAC_N3000

> + tristate "FPGA DFL N3000 NIOS Driver"

FPGA DFL NIOS Driver for Intel PAC N3000

> + depends on FPGA_DFL
> + select REGMAP
> + help
> + This is the driver for the N3000 Nios private feature on Intel
> + PAC (Programmable Acceleration Card) N3000. It communicates
> + with the embedded Nios processor to configure the retimers on
> + the card. It also instantiates the SPI master (spi-altera) for
> + the card's BMC (Board Management Controller) control.
> +
> config FPGA_DFL_PCI
> tristate "FPGA DFL PCIe Device Driver"
> depends on PCI && FPGA_DFL
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index d8e21df..27f20f2 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -44,5 +44,7 @@ dfl-fme-objs += dfl-fme-perf.o
> dfl-afu-objs := dfl-afu-main.o dfl-afu-region.o dfl-afu-dma-region.o
> dfl-afu-objs += dfl-afu-error.o
>
> +obj-$(CONFIG_FPGA_DFL_N3000_NIOS) += dfl-n3000-nios.o
> +
> # Drivers for FPGAs which implement DFL
> obj-$(CONFIG_FPGA_DFL_PCI) += dfl-pci.o
> diff --git a/drivers/fpga/dfl-n3000-nios.c b/drivers/fpga/dfl-n3000-nios.c
> new file mode 100644
> index 0000000..aeac224
> --- /dev/null
> +++ b/drivers/fpga/dfl-n3000-nios.c
> @@ -0,0 +1,528 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * DFL device driver for Nios private feature on Intel PAC (Programmable
> + * Acceleration Card) N3000
> + *
> + * Copyright (C) 2019-2020 Intel Corporation, Inc.
> + *
> + * Authors:
> + * Wu Hao <hao.wu@xxxxxxxxx>
> + * Xu Yilun <yilun.xu@xxxxxxxxx>
> + */
> +#include <linux/bitfield.h>
> +#include <linux/errno.h>
> +#include <linux/io.h>
> +#include <linux/io-64-nonatomic-lo-hi.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/stddef.h>
> +#include <linux/spi/altera.h>
> +#include <linux/spi/spi.h>
> +#include <linux/types.h>
> +
> +#include "dfl.h"
> +
> +static char *fec_mode = "rs";
> +module_param(fec_mode, charp, 0444);
> +MODULE_PARM_DESC(fec_mode, "FEC mode of the ethernet retimer on
> Intel PAC N3000");
> +
> +/* N3000 Nios private feature registers */
> +#define NIOS_SPI_PARAM 0x8
> +#define PARAM_SHIFT_MODE_MSK BIT_ULL(1)
> +#define PARAM_SHIFT_MODE_MSB 0
> +#define PARAM_SHIFT_MODE_LSB 1
> +#define PARAM_DATA_WIDTH GENMASK_ULL(7, 2)
> +#define PARAM_NUM_CS GENMASK_ULL(13, 8)
> +#define PARAM_CLK_POL BIT_ULL(14)
> +#define PARAM_CLK_PHASE BIT_ULL(15)
> +#define PARAM_PERIPHERAL_ID GENMASK_ULL(47, 32)
> +
> +#define NIOS_SPI_CTRL 0x10
> +#define CTRL_WR_DATA GENMASK_ULL(31, 0)
> +#define CTRL_ADDR GENMASK_ULL(44, 32)
> +#define CTRL_CMD_MSK GENMASK_ULL(63, 62)
> +#define CTRL_CMD_NOP 0
> +#define CTRL_CMD_RD 1
> +#define CTRL_CMD_WR 2
> +
> +#define NIOS_SPI_STAT 0x18
> +#define STAT_RD_DATA GENMASK_ULL(31, 0)
> +#define STAT_RW_VAL BIT_ULL(32)
> +
> +/* Nios handshake registers, indirect access */
> +#define NIOS_INIT 0x1000
> +#define NIOS_INIT_DONE BIT(0)
> +#define NIOS_INIT_START BIT(1)
> +/* Mode for PKVL A, link 0, the same below */
> +#define REQ_FEC_MODE_A0_MSK GENMASK(9, 8)
> +#define REQ_FEC_MODE_A1_MSK GENMASK(11, 10)
> +#define REQ_FEC_MODE_A2_MSK GENMASK(13, 12)
> +#define REQ_FEC_MODE_A3_MSK GENMASK(15, 14)
> +#define REQ_FEC_MODE_B0_MSK GENMASK(17, 16)
> +#define REQ_FEC_MODE_B1_MSK GENMASK(19, 18)
> +#define REQ_FEC_MODE_B2_MSK GENMASK(21, 20)
> +#define REQ_FEC_MODE_B3_MSK GENMASK(23, 22)
> +#define REQ_FEC_MODE_NO 0x0
> +#define REQ_FEC_MODE_KR 0x1
> +#define REQ_FEC_MODE_RS 0x2
> +
> +#define NIOS_FW_VERSION 0x1004
> +#define NIOS_FW_VERSION_PATCH GENMASK(23, 20)
> +#define NIOS_FW_VERSION_MINOR GENMASK(27, 24)
> +#define NIOS_FW_VERSION_MAJOR GENMASK(31, 28)
> +
> +#define PKVL_A_MODE_STS 0x1020
> +#define PKVL_B_MODE_STS 0x1024
> +#define PKVL_MODE_STS_GROUP_MSK GENMASK(15, 8)
> +#define PKVL_MODE_STS_GROUP_OK 0x0
> +#define PKVL_MODE_STS_ID_MSK GENMASK(7, 0)
> +/* When GROUP MASK field == GROUP_OK */
> +#define PKVL_MODE_ID_RESET 0x0
> +#define PKVL_MODE_ID_4X10G 0x1
> +#define PKVL_MODE_ID_4X25G 0x2
> +#define PKVL_MODE_ID_2X25G 0x3
> +#define PKVL_MODE_ID_2X25G_2X10G 0x4
> +#define PKVL_MODE_ID_1X25G 0x5
> +
> +#define NS_REGBUS_WAIT_TIMEOUT 10000 /* loop count */
> +#define NIOS_INIT_TIMEOUT 10000000 /* usec */
> +#define NIOS_INIT_TIME_INTV 100000 /* usec */
> +
> +struct n3000_nios {
> + void __iomem *base;
> + struct regmap *regmap;
> + struct device *dev;
> + struct platform_device *altera_spi;
> +};
> +
> +static ssize_t nios_fw_version_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct n3000_nios *ns = dev_get_drvdata(dev);
> + unsigned int val;
> + int ret;
> +
> + ret = regmap_read(ns->regmap, NIOS_FW_VERSION, &val);
> + if (ret)
> + return ret;
> +
> + return sprintf(buf, "%x.%x.%x\n",
> + (u8)FIELD_GET(NIOS_FW_VERSION_MAJOR, val),
> + (u8)FIELD_GET(NIOS_FW_VERSION_MINOR, val),
> + (u8)FIELD_GET(NIOS_FW_VERSION_PATCH, val));
> +}
> +static DEVICE_ATTR_RO(nios_fw_version);
> +
> +#define IS_MODE_STATUS_OK(mode_stat) \
> + (FIELD_GET(PKVL_MODE_STS_GROUP_MSK, (mode_stat)) == \
> + PKVL_MODE_STS_GROUP_OK)
> +
> +#define IS_RETIMER_FEC_CONFIGURABLE(retimer_mode) \
> + ((retimer_mode) != PKVL_MODE_ID_RESET && \
> + (retimer_mode) != PKVL_MODE_ID_4X10G)
> +
> +static int get_retimer_mode(struct n3000_nios *ns, unsigned int
> mode_stat_reg,
> + unsigned int *retimer_mode)
> +{
> + unsigned int val;
> + int ret;
> +
> + ret = regmap_read(ns->regmap, mode_stat_reg, &val);
> + if (ret)
> + return ret;
> +
> + if (!IS_MODE_STATUS_OK(val))
> + return -EFAULT;
> +
> + *retimer_mode = FIELD_GET(PKVL_MODE_STS_ID_MSK, val);
> +
> + return 0;
> +}
> +
> +static ssize_t fec_mode_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct n3000_nios *ns = dev_get_drvdata(dev);
> + unsigned int val, retimer_a_mode, retimer_b_mode, fec_mode;
> + int ret;
> +
> + ret = get_retimer_mode(ns, PKVL_A_MODE_STS, &retimer_a_mode);
> + if (ret)
> + return ret;
> +
> + ret = get_retimer_mode(ns, PKVL_B_MODE_STS, &retimer_b_mode);
> + if (ret)
> + return ret;
> +
> + if (!IS_RETIMER_FEC_CONFIGURABLE(retimer_a_mode) &&
> + !IS_RETIMER_FEC_CONFIGURABLE(retimer_b_mode))
> + return sprintf(buf, "no\n");

It needs to be defined clearly, configurable seems a little confusing.
It seems that hardware supports FEC mode but software can't change it.
Is that true? If it's in some hardware version doesn't support FEC, then
We can make this sysfs not visible, right?

> +
> + ret = regmap_read(ns->regmap, NIOS_INIT, &val);
> + if (ret)
> + return ret;
> +
> + /*
> + * FEC mode should always be the same for all links, as we set them
> + * in this way.
> + */
> + fec_mode = FIELD_GET(REQ_FEC_MODE_A0_MSK, val);
> + if (fec_mode != FIELD_GET(REQ_FEC_MODE_A1_MSK, val) ||
> + fec_mode != FIELD_GET(REQ_FEC_MODE_A2_MSK, val) ||
> + fec_mode != FIELD_GET(REQ_FEC_MODE_A3_MSK, val) ||
> + fec_mode != FIELD_GET(REQ_FEC_MODE_B0_MSK, val) ||
> + fec_mode != FIELD_GET(REQ_FEC_MODE_B1_MSK, val) ||
> + fec_mode != FIELD_GET(REQ_FEC_MODE_B2_MSK, val) ||
> + fec_mode != FIELD_GET(REQ_FEC_MODE_B3_MSK, val))
> + return -EFAULT;
> +
> + switch (fec_mode) {
> + case REQ_FEC_MODE_NO:
> + return sprintf(buf, "no\n");
> + case REQ_FEC_MODE_KR:
> + return sprintf(buf, "kr\n");
> + case REQ_FEC_MODE_RS:
> + return sprintf(buf, "rs\n");
> + }
> +
> + return -EFAULT;
> +}
> +static DEVICE_ATTR_RO(fec_mode);
> +
> +static struct attribute *n3000_nios_attrs[] = {
> + &dev_attr_nios_fw_version.attr,
> + &dev_attr_fec_mode.attr,
> + NULL,
> +};
> +ATTRIBUTE_GROUPS(n3000_nios);
> +
> +static int init_error_detected(struct n3000_nios *ns)
> +{
> + unsigned int val;
> +
> + if (regmap_read(ns->regmap, PKVL_A_MODE_STS, &val))
> + return true;
> +
> + if (!IS_MODE_STATUS_OK(val))
> + return true;
> +
> + if (regmap_read(ns->regmap, PKVL_B_MODE_STS, &val))
> + return true;
> +
> + if (!IS_MODE_STATUS_OK(val))
> + return true;
> +
> + return false;
> +}
> +
> +static void dump_error_stat(struct n3000_nios *ns)
> +{
> + unsigned int val;
> +
> + if (regmap_read(ns->regmap, PKVL_A_MODE_STS, &val))
> + return;
> +
> + dev_info(ns->dev, "PKVL_A_MODE_STS 0x%x\n", val);

dev_err is better?

> +
> + if (regmap_read(ns->regmap, PKVL_B_MODE_STS, &val))
> + return;
> +
> + dev_info(ns->dev, "PKVL_B_MODE_STS 0x%x\n", val);
> +}
> +
> +static int n3000_nios_init_done_check(struct n3000_nios *ns)
> +{
> + struct device *dev = ns->dev;
> + unsigned int val, mode;
> + int ret;
> +
> + /*
> + * this SPI is shared by Nios core inside FPGA, Nios will use this SPI
> + * master to do some one time initialization after power up, and then
> + * release the control to OS. driver needs to poll on INIT_DONE to
> + * see when driver could take the control.
> + *
> + * Please note that after 3.x.x version, INIT_START is introduced, so
> + * driver needs to trigger START firstly and then check INIT_DONE.
> + */
> +
> + ret = regmap_read(ns->regmap, NIOS_FW_VERSION, &val);
> + if (ret)
> + return ret;
> +
> + /*
> + * If Nios version register is totally uninitialized(== 0x0), then the
> + * Nios firmware is missing. So host could take control of SPI master
> + * safely, but initialization work for Nios is not done. This is an
> + * issue of FPGA image. We didn't error out because we need SPI
> master
> + * to reprogram a new image.

New Nios firmware

> + */
> + if (val == 0) {
> + dev_warn(dev, "Nios version reg = 0x%x, skip INIT_DONE
> check, but the retimer may be uninitialized\n",
> + val);
> + return 0;
> + }
> +
> + if (FIELD_GET(NIOS_FW_VERSION_MAJOR, val) >= 3) {
> + /* read NIOS_INIT to check if PKVL INIT done or not */

Use retimers here instead of PKVLs? Or explain what's the PKVL.

> + ret = regmap_read(ns->regmap, NIOS_INIT, &val);
> + if (ret)
> + return ret;
> +
> + /* check if PKVLs are initialized already */

Same

> + if (val & NIOS_INIT_DONE || val & NIOS_INIT_START)
> + goto nios_init_done;
> +
> + /* configure FEC mode per module param */
> + val = NIOS_INIT_START;
> +
> + /*
> + * When the retimer is to be set to 10G mode, there is no FEC
> + * mode setting, so the REQ_FEC_MODE field will be ignored
> by
> + * Nios firmware in this case. But we should still fill the FEC
> + * mode field cause host could not get the retimer working
> mode
> + * until the Nios init is done.

So you mean hardware will ignore this request in configuration which doesn't
support FEC mode.

Hao

> + */
> + if (!strcmp(fec_mode, "no"))
> + mode = REQ_FEC_MODE_NO;
> + else if (!strcmp(fec_mode, "kr"))
> + mode = REQ_FEC_MODE_KR;
> + else if (!strcmp(fec_mode, "rs"))
> + mode = REQ_FEC_MODE_RS;
> + else
> + return -EINVAL;
> +
> + /* set the same FEC mode for all links */
> + val |= FIELD_PREP(REQ_FEC_MODE_A0_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_A1_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_A2_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_A3_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_B0_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_B1_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_B2_MSK, mode) |
> + FIELD_PREP(REQ_FEC_MODE_B3_MSK, mode);
> +
> + ret = regmap_write(ns->regmap, NIOS_INIT, val);
> + if (ret)
> + return ret;
> + }
> +
> +nios_init_done:
> + /* polls on NIOS_INIT_DONE */
> + ret = regmap_read_poll_timeout(ns->regmap, NIOS_INIT, val,
> + val & NIOS_INIT_DONE,
> + NIOS_INIT_TIME_INTV,
> + NIOS_INIT_TIMEOUT);
> + if (ret) {
> + dev_err(dev, "NIOS_INIT_DONE %s\n",
> + (ret == -ETIMEDOUT) ? "timed out" : "check error");
> + goto dump_sts;
> + }
> +
> + /*
> + * after INIT_DONE is detected, it still needs to check if any ERR
> + * detected.
> + */
> + if (init_error_detected(ns)) {
> + /*
> + * We won't error out here even if error detected. Although
> the
> + * retimer configuration is fail, the Nios will still release
> + * the spi controller for host to communicate with the BMC.
> So
> + * the driver could continue to instantiate the spi controller
> + * device.
> + */
> + dev_warn(dev, "NIOS_INIT_DONE OK, but err found during
> init\n");
> + goto dump_sts;
> + }
> + return 0;
> +
> +dump_sts:
> + dump_error_stat(ns);
> +
> + return ret;
> +}
> +
> +struct spi_board_info m10_n3000_info = {
> + .modalias = "m10-n3000",
> + .max_speed_hz = 12500000,
> + .bus_num = 0,
> + .chip_select = 0,
> +};
> +
> +static int create_altera_spi_controller(struct n3000_nios *ns)
> +{
> + struct altera_spi_platform_data pdata = { 0 };
> + struct platform_device_info pdevinfo = { 0 };
> + void __iomem *base = ns->base;
> + u64 v;
> +
> + v = readq(base + NIOS_SPI_PARAM);
> +
> + pdata.mode_bits = SPI_CS_HIGH;
> + if (FIELD_GET(PARAM_CLK_POL, v))
> + pdata.mode_bits |= SPI_CPOL;
> + if (FIELD_GET(PARAM_CLK_PHASE, v))
> + pdata.mode_bits |= SPI_CPHA;
> +
> + pdata.num_chipselect = FIELD_GET(PARAM_NUM_CS, v);
> + pdata.bits_per_word_mask =
> + SPI_BPW_RANGE_MASK(1, FIELD_GET(PARAM_DATA_WIDTH,
> v));
> +
> + pdata.num_devices = 1;
> + pdata.devices = &m10_n3000_info;
> +
> + dev_dbg(ns->dev, "%s cs %u bpm 0x%x mode 0x%x\n", __func__,
> + pdata.num_chipselect, pdata.bits_per_word_mask,
> + pdata.mode_bits);
> +
> + pdevinfo.name = "subdev_spi_altera";
> + pdevinfo.id = PLATFORM_DEVID_AUTO;
> + pdevinfo.parent = ns->dev;
> + pdevinfo.data = &pdata;
> + pdevinfo.size_data = sizeof(pdata);
> +
> + ns->altera_spi = platform_device_register_full(&pdevinfo);
> + return PTR_ERR_OR_ZERO(ns->altera_spi);
> +}
> +
> +static void destroy_altera_spi_controller(struct n3000_nios *ns)
> +{
> + platform_device_unregister(ns->altera_spi);
> +}
> +
> +/* ns is the abbreviation of nios_spi */
> +static int ns_poll_stat_timeout(void __iomem *base, u64 *v)
> +{
> + int loops = NS_REGBUS_WAIT_TIMEOUT;
> +
> + /*
> + * We don't use the time based timeout here for performance.
> + *
> + * The regbus read/write is on the critical path of Intel PAC N3000
> + * image programing. The time based timeout checking will add too
> much
> + * overhead on it. Usually the state changes in 1 or 2 loops on the
> + * test server, and we set 10000 times loop here for safety.
> + */
> + do {
> + *v = readq(base + NIOS_SPI_STAT);
> + if (*v & STAT_RW_VAL)
> + break;
> + cpu_relax();
> + } while (--loops);
> +
> + return loops ? 0 : -ETIMEDOUT;
> +}
> +
> +static int ns_reg_write(void *context, unsigned int reg, unsigned int val)
> +{
> + struct n3000_nios *ns = context;
> + u64 v = 0;
> + int ret;
> +
> + v |= FIELD_PREP(CTRL_CMD_MSK, CTRL_CMD_WR);
> + v |= FIELD_PREP(CTRL_ADDR, reg);
> + v |= FIELD_PREP(CTRL_WR_DATA, val);
> + writeq(v, ns->base + NIOS_SPI_CTRL);
> +
> + ret = ns_poll_stat_timeout(ns->base, &v);
> + if (ret)
> + dev_err(ns->dev, "fail to write reg 0x%x val 0x%x: %d\n",
> + reg, val, ret);
> +
> + return ret;
> +}
> +
> +static int ns_reg_read(void *context, unsigned int reg, unsigned int *val)
> +{
> + struct n3000_nios *ns = context;
> + u64 v = 0;
> + int ret;
> +
> + v |= FIELD_PREP(CTRL_CMD_MSK, CTRL_CMD_RD);
> + v |= FIELD_PREP(CTRL_ADDR, reg);
> + writeq(v, ns->base + NIOS_SPI_CTRL);
> +
> + ret = ns_poll_stat_timeout(ns->base, &v);
> + if (ret)
> + dev_err(ns->dev, "fail to read reg 0x%x: %d\n", reg, ret);
> + else
> + *val = FIELD_GET(STAT_RD_DATA, v);
> +
> + return ret;
> +}
> +
> +static const struct regmap_config ns_regbus_cfg = {
> + .reg_bits = 32,
> + .reg_stride = 4,
> + .val_bits = 32,
> + .fast_io = true,
> +
> + .reg_write = ns_reg_write,
> + .reg_read = ns_reg_read,
> +};
> +
> +static int n3000_nios_probe(struct dfl_device *dfl_dev)
> +{
> + struct device *dev = &dfl_dev->dev;
> + struct n3000_nios *ns;
> + int ret;
> +
> + ns = devm_kzalloc(dev, sizeof(*ns), GFP_KERNEL);
> + if (!ns)
> + return -ENOMEM;
> +
> + dev_set_drvdata(&dfl_dev->dev, ns);
> +
> + ns->dev = dev;
> +
> + ns->base = devm_ioremap_resource(&dfl_dev->dev, &dfl_dev-
> >mmio_res);
> + if (IS_ERR(ns->base))
> + return PTR_ERR(ns->base);
> +
> + ns->regmap = devm_regmap_init(dev, NULL, ns, &ns_regbus_cfg);
> + if (IS_ERR(ns->regmap))
> + return PTR_ERR(ns->regmap);
> +
> + ret = n3000_nios_init_done_check(ns);
> + if (ret)
> + return ret;
> +
> + ret = create_altera_spi_controller(ns);
> + if (ret)
> + dev_err(dev, "altera spi controller create failed: %d\n", ret);
> +
> + return ret;
> +}
> +
> +static void n3000_nios_remove(struct dfl_device *dfl_dev)
> +{
> + struct n3000_nios *ns = dev_get_drvdata(&dfl_dev->dev);
> +
> + destroy_altera_spi_controller(ns);
> +}
> +
> +#define FME_FEATURE_ID_N3000_NIOS 0xd
> +
> +static const struct dfl_device_id n3000_nios_ids[] = {
> + { FME_ID, FME_FEATURE_ID_N3000_NIOS },
> + { }
> +};
> +
> +static struct dfl_driver n3000_nios_driver = {
> + .drv = {
> + .name = "n3000-nios",
> + .dev_groups = n3000_nios_groups,
> + },
> + .id_table = n3000_nios_ids,
> + .probe = n3000_nios_probe,
> + .remove = n3000_nios_remove,
> +};
> +
> +module_dfl_driver(n3000_nios_driver);
> +
> +MODULE_DEVICE_TABLE(dfl, n3000_nios_ids);
> +MODULE_DESCRIPTION("DFL N3000 Nios private feature driver");
> +MODULE_AUTHOR("Intel Corporation");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4

Next message: Anup Patel: "Re: [PATCH v5 3/9] RISC-V: Implement late mapping page table allocation functions"
Previous message: Stanley Chu: "Re: [PATCH v7] scsi: ufs: Quiesce all scsi devices before shutdown"
In reply to: Xu Yilun: "[PATCH v5 3/3] fpga: dfl: add support for N3000 Nios private feature"
Next in thread: Xu Yilun: "Re: [PATCH v5 3/3] fpga: dfl: add support for N3000 Nios private feature"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]