Re: [greybus-dev] [RFC PATCH v2 3/3] Add Device Tree Bindings for mikroBUS port

[Vaishnav M A]

On Tue, Aug 18, 2020 at 7:05 PM Laurent Pinchart
<laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
>
> Hi Vaishnav,
>
> Thank you for the patch.
>
> On Tue, Aug 18, 2020 at 06:18:15PM +0530, Vaishnav M A wrote:
> > This patch adds device tree bindings for the mikroBUS port,
> > device tree overlays for the mikrobus Port on the BeagleBoard.org
> > PocketBeagle is available here :
> > github.com/beagleboard/bb.org-overlays/blob/master/src/arm/PB-MIKROBUS-0.dts
> >
> > Signed-off-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx>
> > ---
> >  .../bindings/misc/linux,mikrobus.txt          | 81 +++++++++++++++++++
>
> Would you mind converting this binding document to YAML ? For new
> bindings we're trying to enforce usage of YAML, to avoid increasing the
> conversion backlog.
>
Hi Laurent,

Sure, I will convert the device tree binding document to YAML in the
next version.
> >  1 file changed, 81 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/misc/linux,mikrobus.txt
> >
> > diff --git a/Documentation/devicetree/bindings/misc/linux,mikrobus.txt b/Documentation/devicetree/bindings/misc/linux,mikrobus.txt
> > new file mode 100644
> > index 000000000000..99f75caf5f35
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/misc/linux,mikrobus.txt
> > @@ -0,0 +1,81 @@
> > +mikroBUS add-on board socket
> > +
> > +Required properties:
> > +- compatible: Must be "linux,mikrobus"
> > +- i2c-adapter:  phandle to the i2c adapter attached to the mikrobus socket.
> > +- spi-master: spi bus number of the spi-master attached to the mikrobus socket.
> > +- spi-cs: spi chip-select numbers corresponding to the chip-selects
> > +       on the mikrobus socket(0 -> chip select corresponding to CS pin
> > +       1 -> chip select corresponding to RST pin).
> > +- serdev-controller:  phandle to the uart port attached to the mikrobus socket.
> > +- pwms: phandle to the pwm-controller corresponding to the mikroBUS PWM pin.
> > +- mikrobus-gpios: gpios array corresponding to GPIOs on the mikroBUS port,
> > +               for targets not supporting the AN pin on the mikroBUS port as
> > +               GPIO, the length of the gpios array can be 11, otherwise it
> > +               should be 12.
> > +- pinctrl-names: pinctrl state names to support additional pin usage/deviations
> > +              from mikroBUS socket standard usage, must be "default",
> > +              "pwm_default", "pwm_gpio", "uart_default", "uart_gpio",
> > +              "i2c_default", "i2c_gpio", "spi_default", "spi_gpio", these
> > +              pinctrl names should have corresponding pinctrl-N entries which
> > +              corresponds to the pinmux state for the pingroup, for example,
> > +              i2c_default corresponds to the state where the I2C pin group
> > +              (SCL,SDA) are configured in I2C mode and i2c_gpio mode corresponds
> > +              to the pinmux state where these pins are configured as GPIO.
> > +- pinctrl-N : pinctrl-(0-8) corresponds to the pinctrl states for the states described
> > +           above.
> > +
> > +Example:
> > +     mikrobus-0 {
> > +             compatible = "linux,mikrobus";
> > +             status = "okay";
> > +             pinctrl-names = "default", "pwm_default", "pwm_gpio",
> > +                             "uart_default", "uart_gpio", "i2c_default",
> > +                             "i2c_gpio", "spi_default", "spi_gpio";
> > +             pinctrl-0 = <
> > +                     &P2_03_gpio_input_pin
> > +                     &P1_04_gpio_pin
> > +                     &P1_02_gpio_pin
> > +             >;
> > +             pinctrl-1 = <&P2_01_pwm_pin>;
> > +             pinctrl-2 = <&P2_01_gpio_pin>;
> > +             pinctrl-3 = <
> > +                     &P2_05_uart_pin
> > +                     &P2_07_uart_pin
> > +             >;
> > +             pinctrl-4 = <
> > +                     &P2_05_gpio_pin
> > +                     &P2_07_gpio_pin
> > +             >;
> > +             pinctrl-5 = <
> > +                     &P2_09_i2c_pin
> > +                     &P2_11_i2c_pin
> > +             >;
> > +             pinctrl-6 = <
> > +                     &P2_09_gpio_pin
> > +                     &P2_11_gpio_pin
> > +             >;
> > +             pinctrl-7 = <
> > +                     &P1_12_spi_pin
> > +                     &P1_10_spi_pin
> > +                     &P1_08_spi_sclk_pin
> > +                     &P1_06_spi_cs_pin
> > +             >;
> > +             pinctrl-8 = <
> > +                     &P1_12_gpio_pin
> > +                     &P1_10_gpio_pin
> > +                     &P1_08_gpio_pin
> > +                     &P1_06_gpio_pin
> > +             >;
> > +             i2c-adapter = <&i2c1>;
> > +             spi-master = <0>;
> > +             spi-cs = <0 1>;
> > +             serdev-controller = <&uart4>;
> > +             pwms = <&ehrpwm1 0 500000 0>;
> > +             mikrobus-gpios = <&gpio1 18 0> , <&gpio0 23 0>,
> > +                                     <&gpio0 30 0> , <&gpio0 31 0>,
> > +                                     <&gpio0 15 0> , <&gpio0 14 0>,
> > +                                     <&gpio0 4 0> , <&gpio0 3 0>,
> > +                                     <&gpio0 2 0> , <&gpio0 5 0>,
> > +                                     <&gpio2 25 0>  , <&gpio2 3 0>;
> > +     };
> > \ No newline at end of file
>
> --
> Regards,
>
> Laurent Pinchart
Thanks and Regards,

Vaishnav