Re: [PATCH v2 4/4] arm64: dts: imx8mm-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MM

From: Krzysztof Kozlowski
Date: Sun Aug 23 2020 - 04:58:55 EST

On Sun, Aug 23, 2020 at 10:00:51AM +0800, Shawn Guo wrote:
> On Mon, Aug 17, 2020 at 09:01:20AM +0200, Krzysztof Kozlowski wrote:
> > Add a DTS for Variscite Symphony evaluation kit with VAR-SOM-MX8MM
> > System on Module.
> >
> > Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> >
> > ---
> >
> > Changes since v1:
> > 1. Remove duplicated "leds" node,
> > 2. Fix heartbeat to active low,
> > 3. Add nxp,ptn5150 extcon.
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../dts/freescale/imx8mm-var-som-symphony.dts | 248 ++++++++++++++++++
> > 2 files changed, 249 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index a39f0a1723e0..dcfb8750cd78 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -29,6 +29,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> > dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> >
> > dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
> > new file mode 100644
> > index 000000000000..2d3c30ac5e04
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
> > @@ -0,0 +1,248 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (C) 2020 Krzysztof Kozlowski <krzk@xxxxxxxxxx>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx8mm-var-som.dtsi"
> > +
> > +/ {
> > + model = "Variscite VAR-SOM-MX8MM Symphony evaluation board";
> > + compatible = "variscite,var-som-mx8mm-symphony", "variscite,var-som-mx8mm", "fsl,imx8mm";
> > +
> > + reg_usdhc2_vmmc: regulator-1 {
>
> regulator-usdhc2-vmmc

You mean the node name? If so, it's not correct with device tree
specification:
"The node-name (...) should describe the general class of device.:
If appropriate, the name should be one of the following choices:
(...)
- regulator"

Adding specific function/type/usage to the name of the node is a
opposite choice to "general class".


>
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> > + regulator-name = "VSD_3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_usb_otg2_vbus: regulator-2 {
>
> regulator-usb-otg2-vbus
>
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_reg_usb_otg2_vbus>;
> > + regulator-name = "usb_otg2_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + gpio = <&gpio5 1 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + gpio-keys {
> > + compatible = "gpio-keys";
> > +
> > + back {
> > + label = "Back";
> > + gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_BACK>;
> > + };
> > +
> > + home {
> > + label = "Home";
> > + gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_HOME>;
> > + };
> > +
> > + menu {
> > + label = "Menu";
> > + gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
> > + linux,code = <KEY_MENU>;
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + heartbeat {
> > + label = "Heartbeat";
> > + gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +};
> > +
> > +&ethphy {
> > + reset-gpios = <&pca9534 5 GPIO_ACTIVE_HIGH>;
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + pca9534: gpio@20 {
> > + compatible = "nxp,pca9534";
> > + reg = <0x20>;
> > + gpio-controller;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pca9534>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> > + #gpio-cells = <2>;
> > + wakeup-source;
> > +
> > + /* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */
> > + usb3-sata-sel-hog {
> > + gpio-hog;
> > + gpios = <4 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "usb3_sata_sel";
> > + };
> > +
> > + som-vselect-hog {
> > + gpio-hog;
> > + gpios = <6 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "som_vselect";
> > + };
> > +
> > + enet-sel-hog {
> > + gpio-hog;
> > + gpios = <7 GPIO_ACTIVE_HIGH>;
> > + output-low;
> > + line-name = "enet_sel";
> > + };
> > + };
> > +
> > + extcon_usbotg1: typec@3d {
> > + compatible = "nxp,ptn5150";
> > + reg = <0x3d>;
> > + int-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ptn5150>;
> > + status = "okay";
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + /* Capacitive touch controller */
> > + ft5x06_ts: touchscreen@38 {
> > + compatible = "edt,edt-ft5406";
> > + reg = <0x38>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_captouch>;
> > + interrupt-parent = <&gpio5>;
> > + interrupts = <4 GPIO_ACTIVE_HIGH>;
> > +
> > + touchscreen-size-x = <800>;
> > + touchscreen-size-y = <480>;
> > + touchscreen-inverted-x;
> > + touchscreen-inverted-y;
> > + };
> > +
> > + rtc@68 {
> > + compatible = "dallas,ds1337";
> > + reg = <0x68>;
> > + wakeup-source;
> > + };
> > +};
> > +
> > +/* Header */
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +/* Header */
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart3>;
> > + status = "okay";
> > +};
> > +
> > +&usbotg1 {
> > + disable-over-current;
> > + extcon = <&extcon_usbotg1>, <&extcon_usbotg1>;
> > +};
> > +
> > +&usbotg2 {
> > + dr_mode = "host";
> > + vbus-supply = <&reg_usb_otg2_vbus>;
> > + srp-disable;
> > + hnp-disable;
> > + adp-disable;
> > + disable-over-current;
> > + /delete-property/ usb-role-switch;
> > + /*
> > + * FIXME: having USB2 enabled hangs the boot just after:
> > + * [ 1.943365] ci_hdrc ci_hdrc.1: EHCI Host Controller
> > + * [ 1.948287] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
> > + * [ 1.971006] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
> > + * [ 1.977203] hub 1-0:1.0: USB hub found
> > + * [ 1.980987] hub 1-0:1.0: 1 port detected
> > + */
> > + status = "disabled";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
>
> Drop this.

Indeed, thanks.

Best regards,
Krzysztof