Re: [PATCH] drm/bridge/tc358775: Fixes bus formats read

From: Vinay Simha B N
Date: Tue Aug 25 2020 - 10:27:32 EST

Next message: Alex Dewar: "[PATCH] ath11k: return error if firmware request fails"
Previous message: Suren Baghdasaryan: "Re: [PATCH v2 1/1] mm, oom_adj: don't loop through tasks in __set_oom_adj when not necessary"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

laurent,

Please review or give some feedback.

On Thu, Aug 13, 2020 at 9:09 PM Vinay Simha B N <simhavcs@xxxxxxxxx> wrote:
>
> laurent,
>
> The code sequence was a problem. *num_inputs_fmts =
> ARRAY_SIZE(tc_lvds_in_bus_fmts); should come first and then allocate
> the kcalloc.
>
> input_fmts = kcalloc(*num_input_fmts, ARRAY_SIZE(tc_lvds_in_bus_fmts),
> GFP_KERNEL);
> ..
> for (i = 0; i < ARRAY_SIZE(tc_lvds_in_bus_fmts); ++i)
> input_fmts[i] = tc_lvds_in_bus_fmts[i];
>
> *num_inputs_fmts = ARRAY_SIZE(tc_lvds_in_bus_fmts);
>
> So, internally in the drm pipeline get set the input format based on
> the output formats?
>
> On Wed, Aug 12, 2020 at 10:45 PM Vinay Simha B N <simhavcs@xxxxxxxxx> wrote:
> >
> > laurent,
> >
> > if i add the .atomic_get_input_bus_fmts =
> > tc_bridge_get_input_bus_fmts, with the implementation suggested,
> > system does not boot fully, the reason is, we capture all the
> > supported input formats, but not sure where to set the final input
> > format. Please suggest.
> >
> > for (i = 0; i < ARRAY_SIZE(tc_lvds_in_bus_fmts); ++i)
> > input_fmts[i] = tc_lvds_in_bus_fmts[i];
> >
> > *num_input_fmts = ARRAY_SIZE(tc_lvds_in_bus_fmts);
> >
> > On Wed, Aug 12, 2020 at 8:25 PM Vinay Simha B N <simhavcs@xxxxxxxxx> wrote:
> > >
> > > laurent,
> > >
> > > Video data input format : RGB666 loosely packed 24 bits per pixel
> > > Can we use MEDIA_BUS_FMT_RGB666_1X24_CPADHI? There was no information
> > > wrt CPADHI or for loosely packed
> > >
> > > static const u32 tc_lvds_in_bus_fmts[] = {
> > > MEDIA_BUS_FMT_RGB565_1X16,
> > > MEDIA_BUS_FMT_RGB666_1X18,
> > > MEDIA_BUS_FMT_RGB666_1X24_CPADHI,
> > > MEDIA_BUS_FMT_RBG888_1X24,
> > > };
> > >
> > > for (i = 0; i < ARRAY_SIZE(tc_lvds_in_bus_fmts); ++i)
> > > input_fmts[i] = tc_lvds_in_bus_fmts[i];
> > > >> This will have all the available input formats, but finally which video data input format chosen?
> > > Since dsi->format = MIPI_DSI_FMT_RGB888 is used does it chooses
> > > MEDIA_BUS_FMT_RBG888_1X24 by the drm pipeline
> > >
> > > On Wed, Aug 12, 2020 at 6:48 PM Laurent Pinchart
> > > <laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
> > > >
> > > > Hi Vinay,
> > > >
> > > > On Wed, Aug 12, 2020 at 06:07:52PM +0530, Vinay Simha B N wrote:
> > > > > On Wed, Aug 12, 2020 at 3:24 PM Laurent Pinchart wrote:
> > > > > > On Wed, Aug 12, 2020 at 12:55:50PM +0530, Vinay Simha BN wrote:
> > > > > > > - bus formats read from drm_bridge_state.output_bus_cfg.format
> > > > > > > and .atomic_get_input_bus_fmts() instead of connector
> > > > > > >
> > > > > > > Signed-off-by: Vinay Simha BN <simhavcs@xxxxxxxxx>
> > > > > > >
> > > > > > > ---
> > > > > > > v1:
> > > > > > > * Laurent Pinchart review comments incorporated
> > > > > > > drm_bridge_state.output_bus_cfg.format
> > > > > > > instead of connector
> > > > > > > ---
> > > > > > > drivers/gpu/drm/bridge/tc358775.c | 76 ++++++++++++++++++++++++++++++---------
> > > > > > > 1 file changed, 59 insertions(+), 17 deletions(-)
> > > > > > >
> > > > > > > diff --git a/drivers/gpu/drm/bridge/tc358775.c b/drivers/gpu/drm/bridge/tc358775.c
> > > > > > > index 7da15cd..5d8714a 100644
> > > > > > > --- a/drivers/gpu/drm/bridge/tc358775.c
> > > > > > > +++ b/drivers/gpu/drm/bridge/tc358775.c
> > > > > > > @@ -271,6 +271,13 @@ struct tc_data {
> > > > > > > struct gpio_desc *stby_gpio;
> > > > > > > u8 lvds_link; /* single-link or dual-link */
> > > > > > > u8 bpc;
> > > > > > > + u32 output_bus_fmt;
> > > > > > > +};
> > > > > > > +
> > > > > > > +static const u32 tc_lvds_out_bus_fmts[] = {
> > > > > > > + MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA,
> > > > > > > + MEDIA_BUS_FMT_RGB888_1X7X4_SPWG,
> > > > > > > + MEDIA_BUS_FMT_RGB666_1X7X3_SPWG,
> > > > > > > };
> > > > > > >
> > > > > > > static inline struct tc_data *bridge_to_tc(struct drm_bridge *b)
> > > > > > > @@ -359,19 +366,6 @@ static void d2l_write(struct i2c_client *i2c, u16 addr, u32 val)
> > > > > > > ret, addr);
> > > > > > > }
> > > > > > >
> > > > > > > -/* helper function to access bus_formats */
> > > > > > > -static struct drm_connector *get_connector(struct drm_encoder *encoder)
> > > > > > > -{
> > > > > > > - struct drm_device *dev = encoder->dev;
> > > > > > > - struct drm_connector *connector;
> > > > > > > -
> > > > > > > - list_for_each_entry(connector, &dev->mode_config.connector_list, head)
> > > > > > > - if (connector->encoder == encoder)
> > > > > > > - return connector;
> > > > > > > -
> > > > > > > - return NULL;
> > > > > > > -}
> > > > > > > -
> > > > > > > static void tc_bridge_enable(struct drm_bridge *bridge)
> > > > > > > {
> > > > > > > struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > > @@ -380,7 +374,6 @@ static void tc_bridge_enable(struct drm_bridge *bridge)
> > > > > > > u32 val = 0;
> > > > > > > u16 dsiclk, clkdiv, byteclk, t1, t2, t3, vsdelay;
> > > > > > > struct drm_display_mode *mode;
> > > > > > > - struct drm_connector *connector = get_connector(bridge->encoder);
> > > > > > >
> > > > > > > mode = &bridge->encoder->crtc->state->adjusted_mode;
> > > > > > >
> > > > > > > @@ -451,14 +444,13 @@ static void tc_bridge_enable(struct drm_bridge *bridge)
> > > > > > > d2l_write(tc->i2c, LVPHY0, LV_PHY0_PRBS_ON(4) | LV_PHY0_ND(6));
> > > > > > >
> > > > > > > dev_dbg(tc->dev, "bus_formats %04x bpc %d\n",
> > > > > > > - connector->display_info.bus_formats[0],
> > > > > > > + tc->output_bus_fmt,
> > > > > > > tc->bpc);
> > > > > > > /*
> > > > > > > * Default hardware register settings of tc358775 configured
> > > > > > > * with MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA jeida-24 format
> > > > > > > */
> > > > > > > - if (connector->display_info.bus_formats[0] ==
> > > > > > > - MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) {
> > > > > > > + if (tc->output_bus_fmt == MEDIA_BUS_FMT_RGB888_1X7X4_SPWG) {
> > > > > > > /* VESA-24 */
> > > > > > > d2l_write(tc->i2c, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
> > > > > > > d2l_write(tc->i2c, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0));
> > > > > > > @@ -590,6 +582,51 @@ static int tc358775_parse_dt(struct device_node *np, struct tc_data *tc)
> > > > > > > return 0;
> > > > > > > }
> > > > > > >
> > > > > > > +static int tc_bridge_atomic_check(struct drm_bridge *bridge,
> > > > > > > + struct drm_bridge_state *bridge_state,
> > > > > > > + struct drm_crtc_state *crtc_state,
> > > > > > > + struct drm_connector_state *conn_state)
> > > > > > > +{
> > > > > > > + struct tc_data *tc = bridge_to_tc(bridge);
> > > > > > > +
> > > > > > > + tc->output_bus_fmt = bridge_state->output_bus_cfg.format;
> > > > > >
> > > > > > .atomic_check() isn't allowed to modify the device state, neither the
> > > > > > hardware state nor the software state in drm_bridge or tc_data. You can
> > > > > > instead access the bridge state directly in tc_bridge_enable(), with
> > > > > >
> > > > > > struct drm_bridge_state *state =
> > > > > > drm_priv_to_bridge_state(bridge->base.state);
> > > > >
> > > > > Currently the driver is picking up from the dts panel
> > > > > (data-mapping = "vesa-24";) or jeida-24 or jeida-18.
> > > > >
> > > > > Does state->output_bus_cfg.format get set from the data-mapping?
> > > >
> > > > It should. The drm_panel should take care of that. In
> > > > panel_simple_get_non_edid_modes(), it calls
> > > >
> > > > if (panel->desc->bus_format)
> > > > drm_display_info_set_bus_formats(&connector->display_info,
> > > > &panel->desc->bus_format, 1);
> > > >
> > > > to initialize the bus format in display_info. Then, the DRM bridge
> > > > helper drm_atomic_bridge_chain_select_bus_fmts() retrieves the output
> > > > format by calling .atomic_get_output_bus_fmts() if implemented by the
> > > > last bridge in the chain, or directly from the connector display_info.
> > > > The last bridge in the chain is a DRM panel bridge, and doesn't
> > > > implement .atomic_get_output_bus_fmts(), so the format from display_info
> > > > is used, and is stored in the output_bus_cfg.format field of this bridge
> > > > in select_bus_fmt_recursive().
> > > >
> > > > If something doesn't work according to the plan, I can help you
> > > > debugging.
> > > >
> > > > > > > +
> > > > > > > + dev_dbg(tc->dev, "output_bus_fmt %04x\n", tc->output_bus_fmt);
> > > > > > > +
> > > > > > > + return 0;
> > > > > > > +}
> > > > > > > +
> > > > > > > +static u32 *
> > > > > > > +tc_bridge_get_input_bus_fmts(struct drm_bridge *bridge,
> > > > > > > + struct drm_bridge_state *bridge_state,
> > > > > > > + struct drm_crtc_state *crtc_state,
> > > > > > > + struct drm_connector_state *conn_state,
> > > > > > > + u32 output_fmt,
> > > > > > > + unsigned int *num_input_fmts)
> > > > > > > +{
> > > > > > > + u32 *input_fmts = NULL;
> > > > > > > + int i;
> > > > > >
> > > > > > i only takes positive values, so it can be an unsigned int.
> > > > > >
> > > > > > > +
> > > > > > > + *num_input_fmts = 0;
> > > > > > > +
> > > > > > > + for (i = 0 ; i < ARRAY_SIZE(tc_lvds_out_bus_fmts) ; ++i) {
> > > > > > > + if (output_fmt == tc_lvds_out_bus_fmts[i]) {
> > > > > > > + *num_input_fmts = 1;
> > > > > > > + input_fmts = kcalloc(*num_input_fmts,
> > > > > > > + sizeof(*input_fmts),
> > > > > > > + GFP_KERNEL);
> > > > > > > + if (!input_fmts)
> > > > > > > + return NULL;
> > > > > > > +
> > > > > > > + input_fmts[0] = output_fmt;
> > > > > >
> > > > > > I don't think this is right, the input of the bridge isn't LVDS, is it ?
> > > > >
> > > > > Input to the bridge is DSI, format is already set
> > > > >
> > > > > dsi->format = MIPI_DSI_FMT_RGB888;
> > > > >
> > > > > enum mipi_dsi_pixel_format {
> > > > > MIPI_DSI_FMT_RGB888,
> > > > > MIPI_DSI_FMT_RGB666,
> > > > > MIPI_DSI_FMT_RGB666_PACKED,
> > > > > MIPI_DSI_FMT_RGB565,
> > > > > };
> > > > > include/drm/drm_mipi_dsi.h
> > > > >
> > > > > Why do we require this atomic_get_input_bus_fmts?
> > > > >
> > > > > Do i need to implement both atomic_get_input_bus_fmts and
> > > > > atomic_get_output_bus_fmts?
> > > >
> > > > .atomic_get_output_bus_fmts() is only need for the last bridge in the
> > > > chain, and is not mandatory when that bridge supports a single format.
> > > > As this bridge can't be last (if the output is connect to a panel, there
> > > > will be a drm_bridge wrapping the drm_panel), you don't have to
> > > > implement that operation.
> > > >
> > > > .atomic_get_input_bus_fmts() is used to negotiate formats along the
> > > > pipeline. The helps the DRM bridge helpers figure out what formats are
> > > > possible, with the help of bridges that must report what input formats
> > > > are compatible with a given output format. The DRM bridge helpers will
> > > > take care of the rest.
> > > >
> > > > So, for this bridge, the input and output formats are decoupled. The
> > > > bridge can output any of the three supported LVDS formats, regardless of
> > > > what format it gets at its input. You should thus verify that the output
> > > > format you receive in this function is supported (and return NULL if it
> > > > isn't), and then return the list of supported input formats. If you
> > > > don't implement .atomic_get_input_bus_fmts(), then the DRM bridge
> > > > helpers will consider that the input and output formats are the same,
> > > > and will set the output format of the previous bridge to, for example,
> > > > MEDIA_BUS_FMT_RGB666_1X7X3_SPWG. It may work if the previous bridge
> > > > doesn't care about its output format, but if it does, then it will be
> > > > puzzled, as the previous bridge outputs DSI, not LVDS.
> > > >
> > > > > > As far as I can tell, the hardware support transcoding any of the
> > > > > > supported input formats (RGB565, RGB666 or RGB888) to any of the
> > > > > > supported output formats. How about the following ?
> > > > > >
> > > > > > static const u32 tc_lvds_in_bus_fmts[] = {
> > > > > > MEDIA_BUS_FMT_RGB565_1X16,
> > > > > > MEDIA_BUS_FMT_RGB666_1X18,
> > > > > > MEDIA_BUS_FMT_RBG888_1X24,
> > > > > > };
> > > > > >
> > > > > > ...
> > > > > >
> > > > > > u32 *input_fmts;
> > > > > > unsigned int i;
> > > > > >
> > > > > > *num_input_fmts = 0;
> > > > > >
> > > > > > for (i = 0 ; i < ARRAY_SIZE(tc_lvds_out_bus_fmts) ; ++i) {
> > > > > > if (output_fmt == tc_lvds_out_bus_fmts[i])
> > > > > > break;
> > > > > > }
> > > > > >
> > > > > > if (i == ARRAY_SIZE(tc_lvds_out_bus_fmts))
> > > > > > return NULL;
> > > > > >
> > > > > > input_fmts = kcalloc(*num_input_fmts, ARRAY_SIZE(tc_lvds_in_bus_fmts),
> > > > > > GFP_KERNEL);
> > > > > > if (!input_fmts)
> > > > > > return NULL;
> > > > > >
> > > > > > for (i = 0; i < ARRAY_SIZE(tc_lvds_in_bus_fmts); ++i)
> > > > > > input_fmts[i] = tc_lvds_in_bus_fmts[i];
> > > > > >
> > > > > > *num_inputs_fmts = ARRAY_SIZE(tc_lvds_in_bus_fmts);
> > > > > > return input_fmts;
> > > > > >
> > > > > > > +
> > > > > > > + break;
> > > > > > > + }
> > > > > > > + }
> > > > > > > +
> > > > > > > + return input_fmts;
> > > > > > > +}
> > > > > > > +
> > > > > > > static int tc_bridge_attach(struct drm_bridge *bridge,
> > > > > > > enum drm_bridge_attach_flags flags)
> > > > > > > {
> > > > > > > @@ -639,6 +676,11 @@ static int tc_bridge_attach(struct drm_bridge *bridge,
> > > > > > > }
> > > > > > >
> > > > > > > static const struct drm_bridge_funcs tc_bridge_funcs = {
> > > > > > > + .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
> > > > > > > + .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
> > > > > > > + .atomic_reset = drm_atomic_helper_bridge_reset,
> > > > > > > + .atomic_get_input_bus_fmts = tc_bridge_get_input_bus_fmts,
> > > > > > > + .atomic_check = tc_bridge_atomic_check,
> > > > > > > .attach = tc_bridge_attach,
> > > > > > > .pre_enable = tc_bridge_pre_enable,
> > > > > > > .enable = tc_bridge_enable,
> > > >
> > > > --
> > > > Regards,
> > > >
> > > > Laurent Pinchart
> > >
> > >
> > >
> > > --
> > > regards,
> > > vinaysimha
> >
> >
> >
> > --
> > regards,
> > vinaysimha
>
>
>
> --
> regards,
> vinaysimha

--
regards,
vinaysimha

Next message: Alex Dewar: "[PATCH] ath11k: return error if firmware request fails"
Previous message: Suren Baghdasaryan: "Re: [PATCH v2 1/1] mm, oom_adj: don't loop through tasks in __set_oom_adj when not necessary"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]