Re: [PATCH v3 05/10] PCI/AER: Extend AER error handling to RCECs
From: sean . v . kelley
Date: Wed Aug 26 2020 - 14:56:09 EST
Hi Sathya,
On Wed, 2020-08-26 at 10:26 -0700, Kuppuswamy, Sathyanarayanan wrote:
>
> On 8/12/20 9:46 AM, Sean V Kelley wrote:
> > From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> >
> > Currently the kernel does not handle AER errors for Root Complex
> > integrated End Points (RCiEPs)[0]. These devices sit on a root bus
> > within
> > the Root Complex (RC). AER handling is performed by a Root Complex
> > Event
> > Collector (RCEC) [1] which is a effectively a type of RCiEP on the
> > same
> > root bus.
> >
> > For an RCEC (technically not a Bridge), error messages "received"
> > from
> > associated RCiEPs must be enabled for "transmission" in order to
> > cause a
> > System Error via the Root Control register or (when the Advanced
> > Error
> > Reporting Capability is present) reporting via the Root Error
> > Command
> > register and logging in the Root Error Status register and Error
> > Source
> > Identification register.
> >
> > In addition to the defined OS level handling of the reset flow for
> > the
> > associated RCiEPs of an RCEC, it is possible to also have non-
> > native
> > handling. In that case there is no need to take any actions on the
> > RCEC
> > because the firmware is responsible for them. This is true where
> > APEI [2]
> > is used to report the AER errors via a GHES[v2] HEST entry [3] and
> > relevant AER CPER record [4] and non-native handling is in use.
> >
> > We effectively end up with two different types of discovery for
> > purposes of handling AER errors:
> >
> > 1) Normal bus walk - we pass the downstream port above a bus to
> > which
> > the device is attached and it walks everything below that point.
> >
> > 2) An RCiEP with no visible association with an RCEC as there is no
> > need
> > to walk devices. In that case, the flow is to just call the
> > callbacks for
> > the actual device.
> >
> > A new walk function pci_walk_dev_affected(), similar to
> > pci_bus_walk(),
> > is provided that takes a pci_dev instead of a bus. If that dev
> > corresponds
> > to a downstream port it will walk the subordinate bus of that
> > downstream
> > port. If the dev does not then it will call the function on that
> > device
> > alone.
> >
> > [0] ACPI PCI Express Base Specification 5.0-1 1.3.2.3 Root Complex
> > Integrated Endpoint Rules.
> > [1] ACPI PCI Express Base Specification 5.0-1 6.2 Error Signalling
> > and
> > Logging
> > [2] ACPI Specification 6.3 Chapter 18 ACPI Platform Error Interface
> > (APEI)
> > [3] ACPI Specification 6.3 18.2.3.7 Generic Hardware Error Source
> > [4] UEFI Specification 2.8, N.2.7 PCI Express Error Section
> >
> > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> > Signed-off-by: Sean V Kelley <sean.v.kelley@xxxxxxxxx>
> > ---
> > drivers/pci/pcie/err.c | 54 ++++++++++++++++++++++++++++++++++---
> > -----
> > 1 file changed, 44 insertions(+), 10 deletions(-)
> >
> > diff --git a/drivers/pci/pcie/err.c b/drivers/pci/pcie/err.c
> > index 14bb8f54723e..f4cfb37c26c1 100644
> > --- a/drivers/pci/pcie/err.c
> > +++ b/drivers/pci/pcie/err.c
> > @@ -146,38 +146,68 @@ static int report_resume(struct pci_dev *dev,
> > void *data)
> > return 0;
> > }
> >
> > +/**
> > + * pci_walk_dev_affected - walk devices potentially AER affected
> > + * @dev device which may be an RCEC with associated RCiEPs,
> > + * an RCiEP associated with an RCEC, or a Port.
> > + * @cb callback to be called for each device found
> > + * @userdata arbitrary pointer to be passed to callback.
> > + *
> > + * If the device provided is a bridge, walk the subordinate bus,
> > + * including any bridged devices on buses under this bus.
> > + * Call the provided callback on each device found.
> > + *
> > + * If the device provided has no subordinate bus, call the
> > provided
> > + * callback on the device itself.
> > + */
> > +static void pci_walk_dev_affected(struct pci_dev *dev, int
> > (*cb)(struct pci_dev *, void *),
> > + void *userdata)
> > +{
> > + if (dev->subordinate)
> > + pci_walk_bus(dev->subordinate, cb, userdata);
> > + else
> > + cb(dev, userdata);
> > +}
> > +
> > pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
> > enum pci_channel_state state,
> > pci_ers_result_t (*reset_link)(struct pci_dev
> > *pdev))
> > {
> > pci_ers_result_t status = PCI_ERS_RESULT_CAN_RECOVER;
> > - struct pci_bus *bus;
> >
> > /*
> > * Error recovery runs on all subordinates of the first
> > downstream port.
> > * If the downstream port detected the error, it is cleared at
> > the end.
> > + * For RCiEPs we should reset just the RCiEP itself.
> > */
> > if (!(pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
> > - pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM))
> > + pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM ||
> > + pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END ||
> > + pci_pcie_type(dev) == PCI_EXP_TYPE_RC_EC))
> > dev = dev->bus->self;
> > - bus = dev->subordinate;
> >
> > pci_dbg(dev, "broadcast error_detected message\n");
> > if (state == pci_channel_io_frozen) {
> > - pci_walk_bus(bus, report_frozen_detected, &status);
> > + pci_walk_dev_affected(dev, report_frozen_detected,
> > &status);
> > + if (pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END) {
> > + pci_warn(dev, "link reset not possible for
> > RCiEP\n");
> > + status = PCI_ERS_RESULT_NONE;
> > + goto failed;
> reset_link is not applicable for RC_END, but why do you want to fail
> it?
This patch is incorporated prior to the addition of the dev->rcec link
for actually handling the RC_END case. This is the first part before I
bring in the rest and is the basis also of Jonathan's original work.
See subsequent patches on top of err.c in this v3 series.
> > + }
> > +
> > status = reset_link(dev);
> > if (status != PCI_ERS_RESULT_RECOVERED) {
> > pci_warn(dev, "link reset failed\n");
> > goto failed;
> > }
> > } else {
> > - pci_walk_bus(bus, report_normal_detected, &status);
> > + pci_walk_dev_affected(dev, report_normal_detected,
> > &status);
> > }
> >
> > if (status == PCI_ERS_RESULT_CAN_RECOVER) {
> > status = PCI_ERS_RESULT_RECOVERED;
> > pci_dbg(dev, "broadcast mmio_enabled message\n");
> > - pci_walk_bus(bus, report_mmio_enabled, &status);
> > + pci_walk_dev_affected(dev, report_mmio_enabled,
> > &status);
> > }
> >
> > if (status == PCI_ERS_RESULT_NEED_RESET) {
> > @@ -188,17 +218,21 @@ pci_ers_result_t pcie_do_recovery(struct
> > pci_dev *dev,
> > */
> > status = PCI_ERS_RESULT_RECOVERED;
> > pci_dbg(dev, "broadcast slot_reset message\n");
> > - pci_walk_bus(bus, report_slot_reset, &status);
> > + pci_walk_dev_affected(dev, report_slot_reset, &status);
> > }
> >
> > if (status != PCI_ERS_RESULT_RECOVERED)
> > goto failed;
> >
> > pci_dbg(dev, "broadcast resume message\n");
> > - pci_walk_bus(bus, report_resume, &status);
> > + pci_walk_dev_affected(dev, report_resume, &status);
> >
> > - pci_aer_clear_device_status(dev);
> > - pci_aer_clear_nonfatal_status(dev);
> you want to prevent clearing status for RC_END ? Can you explain?
It's the RC_EC of the associated RC_END which is to be cleared.
However, in this original patch from Jonathan prior to my subsequent
addition of dev->rcec it is not possible. The important thing is not to
attempt to clear the RC_END without the association.
See subsequent patches on top of err.c in this v3 series.
Thanks,
Sean
> > + if ((pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
> > + pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM ||
> > + pci_pcie_type(dev) == PCI_EXP_TYPE_RC_EC)) {
> > + pci_aer_clear_device_status(dev);
> > + pci_aer_clear_nonfatal_status(dev);
> > + }
> > pci_info(dev, "device recovery successful\n");
> > return status;
> >
> >