Re: [PATCH v2] media: rcar-vin: Add support to select data pins for YCbCr422-8bit input

[Lad, Prabhakar]

On Tue, Aug 11, 2020 at 6:40 PM Lad, Prabhakar
<prabhakar.csengg@xxxxxxxxx> wrote:
>
> Hi Laurent,
>
> On Tue, Aug 11, 2020 at 12:41 PM Laurent Pinchart
> <laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
> >
> > Hi Prabhakar,
> >
> > On Fri, Aug 07, 2020 at 09:20:36PM +0100, Lad, Prabhakar wrote:
> > > On Wed, Aug 5, 2020 at 1:35 PM Laurent Pinchart wrote:
> > > > On Wed, Aug 05, 2020 at 10:43:25AM +0200, Geert Uytterhoeven wrote:
> > > >> On Wed, Aug 5, 2020 at 10:01 AM Lad, Prabhakar wrote:
> > > >>> On Tue, Aug 4, 2020 at 4:32 PM Geert Uytterhoeven wrote:
> > > >>>> On Tue, Aug 4, 2020 at 5:12 PM Lad, Prabhakar wrote:
> > > >>>>> On Tue, Aug 4, 2020 at 11:17 AM Geert Uytterhoeven wrote:
> > > >>>>>> On Tue, Aug 4, 2020 at 12:05 PM Niklas wrote:
> > > >>>>>>> On 2020-08-04 09:04:25 +0100, Lad, Prabhakar wrote:
> > > >>>>>>>> On Mon, Aug 3, 2020 at 8:28 PM Niklas wrote:
> > > >>>>>>>>> On 2020-08-03 20:17:54 +0100, Lad, Prabhakar wrote:
> > > >>>>>>>>>> On Mon, Aug 3, 2020 at 7:06 PM Niklas wrote:
> > > >>>>>>>>>>> On 2020-08-03 17:02:53 +0100, Lad Prabhakar wrote:
> > > >>>>>>>>>>>> Select the data pins for YCbCr422-8bit input format depending on
> > > >>>>>>>>>>>> bus_width and data_shift passed as part of DT.
> > > >>>>>>>>>>>>
> > > >>>>>>>>>>>> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > > >>>>>>>>>>>> Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > > >>>>>>>>>>>>
> > > >>>>>>>>>>>> --- a/drivers/media/platform/rcar-vin/rcar-core.c
> > > >>>>>>>>>>>> +++ b/drivers/media/platform/rcar-vin/rcar-core.c
> > > >>>>>>>>>>>> @@ -624,6 +624,11 @@ static int rvin_parallel_parse_v4l2(struct device *dev,
> > > >>>>>>>>>>>>       vin->parallel = rvpe;
> > > >>>>>>>>>>>>       vin->parallel->mbus_type = vep->bus_type;
> > > >>>>>>>>>>>>
> > > >>>>>>>>>>>> +     /* select VInDATA[15:8] pins for YCbCr422-8bit format */
> > > >>>>>>>>>>>> +     if (vep->bus.parallel.bus_width == BUS_WIDTH_8 &&
> > > >>>>>>>>>>>> +         vep->bus.parallel.data_shift == DATA_SHIFT_8)
> > > >>>>>>>>>>>> +             vin->parallel->ycbcr_8b_g = true;
> > > >>>>>>>>>>>> +
> > > >>>>>>>>>>>
> > > >>>>>>>>>>> I would store the bus_width and bus_shift values in the struct
> > > >>>>>>>>>>> rvin_parallel_entity and evaluate them in place rater then create a flag
> > > >>>>>>>>>>> for this specific use-case..
> > > >>>>>>>>>>>
> > > >>>>>>>>>> Ok will do that.
> > > >>>>>>>>>>
> > > >>>>>>>>>>> Also according to the documentation is the check correct? Do we not wish
> > > >>>>>>>>>>> to use the new mode when bus_width == 16 and bus_shift == 8. The check
> > > >>>>>>>>>>> you have here seems to describe a 8 lane bus where 0 lanes are used.
> > > >>>>>>>>>>>
> > > >>>>>>>>>> bus-width is the actual data lines used, so bus_width == 16 and
> > > >>>>>>>>>> bus_shift == 8 would mean use lines 23:8, so just check for bus_width
> > > >>>>>>>>>> == 8 and bus_shift == 8 should be sufficient.
> > > >>>>>>>>>
> > > >>>>>>>>> As you and Geert points out I was wrong, they should indeed both be 8.
> > > >>>>>>>>>
> > > >>>>>>>>>>
> > > >>>>>>>>>>> I think you should also verify that bus_shift is either 0 or 8 as that
> > > >>>>>>>>>>> is all the driver supports.
> > > >>>>>>>>>>>
> > > >>>>>>>>>> Not sure if thats correct.In that case this patch wont make sense, I
> > > >>>>>>>>>> believed we agreed upon we determine the YDS depending on both
> > > >>>>>>>>>> bus-width and bus-shift.
> > > >>>>>>>>>
> > > >>>>>>>>> I'm sorry I think I lost you :-) The driver is not capable of supporting
> > > >>>>>>>>> bus_width = 8 and bus_shift = 2 right? Maybe we are talking about
> > > >>>>>>>>> different things.
> > > >>>>>>>>>
> > > >>>>>>>>> What I tried to say (updated with the knowledge of that bus_width should
> > > >>>>>>>>> indeed be 8 and not 16) was that would it make sens to with bus_width=8
> > > >>>>>>>>> allow for a bus_shift value other then 0 or 8? What for example would
> > > >>>>>>>>> the driver do if the value was 2?
> > > >>>>>>>>>
> > > >>>>>>>> I think this should be possible but I am not sure how this will work.
> > > >>>>>>>> For example on iWave G21D-Q7 platform with 16-bit wired bus say we
> > > >>>>>>>> connect a 8-bit camera as below:
> > > >>>>>>>>
> > > >>>>>>>> bus-width = 8 and bus-shift = 2
> > > >>>>>>>> VI1_G0_B        -> Not connected
> > > >>>>>>>> VI1_G1_B        -> Not connected
> > > >>>>>>>> VI1_G2_B_16        -> Connected
> > > >>>>>>>> VI1_G3_B        -> Connected
> > > >>>>>>>> VI1_G4_B        -> Connected
> > > >>>>>>>> VI1_G5_B        -> Connected
> > > >>>>>>>> VI1_G6_B        -> Connected
> > > >>>>>>>> VI1_G7_B        -> Connected
> > > >>>>>>>> VI1_DATA7_B/VI1_B7_B_16    -> Connected
> > > >>>>>>>> VI1_DATA6_B/VI1_B6_B_16    -> Connected
> > > >>>>>>>> VI1_DATA5_B/VI1_B5_B_16    -> Not connected
> > > >>>>>>>> VI1_DATA4_B/VI1_B4_B_16    -> Not connected
> > > >>>>>>>> VI1_DATA3_B/VI1_B3_B_16    -> Not connected
> > > >>>>>>>> VI1_DATA2_B/VI1_B2_B_16    -> Not connected
> > > >>>>>>>> VI1_DATA1_B/VI1_B1_B_16    -> Not connected
> > > >>>>>>>> VI1_DATA0_B/VI1_B0_B_16    -> Not connected
> > > >>>>>>>
> > > >>>>>>> I agree this is how I would imagine bus-width = 8 and bus-shift = 2 to
> > > >>>>>>> be wired.
> > > >>>>>>>
> > > >>>>>>>> So in this case for 8-bit YCbCr422 format should YDS be set I am not
> > > >>>>>>>> sure. Or is this not a valid case at all ?
> > > >>>>>>>
> > > >>>>>>> That is my question :-)
> > > >>>>>>>
> > > >>>>>>> I can't find anything int the documentation that would allow is to do
> > > >>>>>>> anything other then bus-width = 8 together with bus-shift = 0 (do not
> > > >>>>>>> set YDS) or bus-shift = 8 (set YDS). So that is why I suggested you
> > > >>>>>>> check for this and print a warning if bus-shift is anything else :-)
> > > >>>>>>>
> > > >>>>>>> But if you can figured out how we can do a bus-shift = 2 as in your
> > > >>>>>>> example then of course the check is wrong. I have not read the docs
> > > >>>>>>> carefully enough about this to rule it out as impossible.
> > > >>>>>>
> > > >>>>>> IIUIC, this is a completely different scenario than "low" or "high" wiring
> > > >>>>>> of 8-bit YCbCr-422, hence YDS does not apply?
> > > >>>>>>
> > > >>>>> I tend to agree. We only enable YDS if bus-width = 8 and bus-shift=8
> > > >>>>> as done by this patch. (Although there isn't enough documentation to
> > > >>>>> prove it)
> > > >>>>>
> > > >>>>>> The iWave G21D-Q7 wiring seems to be 10-bit YCbCr-422 with the 2 LSB
> > > >>>>>> bits unconnected?
> > > >>>>>>
> > > >>>>> B-8bit/ BG-16 bit for VI0 and  B-8bit/ BG-16 bit for VI0
> > > >>>>>
> > > >>>>>> Interestingly, that mode is supported on all RZ/G1 SoCs, on most R-Car
> > > >>>>>> Gen3 SoCs, but only on a single R-Car Gen2 SoC (V2H).
> > > >>>>>>
> > > >>>>> YDS mode ?
> > > >>>>
> > > >>>> No, 10-bit YCbCr-422. But please forget my comment, I was looking at
> > > >>>> the wrong table.
> > > >>>>
> > > >>>> VI1_G[7:2] plus VI1_DATA[7:6] is not even a contiguous subset (I had
> > > >>>> misread the used subset to be G[1:0] and B[7:2]), so it cannot be represented
> > > >>>> using just bus-width and bus-shift properties?
> > > >>>>
> > > >>> Yes and here is my explanation.
> > > >>>
> > > >>> In Gen1 manual for YDS bit it says the below:
> > > >>> 0: Vin_B[7:0] pins
> > > >>> 1: Vin_G[7:0] pins
> > > >>>
> > > >>> And in Gen2 manual it says,
> > > >>> 0: Vin_DATA[7:0] pins
> > > >>> 1: Vin_DATA[7:0] pins
> > > >>
> > > >> Vin_DATA[15:8]
> > > >>
> > > >> The difference is due to some SoCs naming the signals R[7:0], G[7:0], B[7:0],
> > > >> while other SoCs use DATA[23:0], the latter presumably to avoid
> > > >> confusion when using non-RGB input formats.
> > > >> R-Car V2H uses a mix: D[23:16]_R[7:0], D[15:8]_G[7:0], D[7:0]_B[7:0] ;-)
> > > >>
> > > >> However, the underlying behavior is the same, which is clear from the
> > > >> RGB-666 mode, which is not using contiguous DATA[17:0], but sparse
> > > >> DATA[23:18], DATA[15:10], DATA[7:2], i.e. the 6 MSB of each color
> > > >> component.
> > > >>
> > > >>> On iwave platform for the VIN2 interface the following G pins are connected:
> > > >>>
> > > >>>  VI2_G0_MARK, VI2_G1_MARK,
> > > >>>  VI2_G2_MARK, VI2_G3_MARK,
> > > >>>  VI2_G4_MARK, VI2_G5_MARK,
> > > >>>  VI2_G6_MARK, VI2_G7_MARK,
> > > >>>
> > > >>> And for capture to work on this interface the YDS bit has to be set.
> > > >>>
> > > >>> Now suppose some day we have a platform with 16 bit interface where G
> > > >>> and R pins are connected:
> > > >>>
> > > >>>         VI2_G0_MARK, VI2_G1_MARK,
> > > >>>         VI2_G2_MARK, VI2_G3_MARK,
> > > >>>         VI2_G4_MARK, VI2_G5_MARK,
> > > >>>         VI2_G6_MARK, VI2_G7_MARK,
> > > >>>         /* R */
> > > >>>         VI2_R0_MARK, VI2_R1_MARK,
> > > >>>         VI2_R2_MARK, VI2_R3_MARK,
> > > >>>         VI2_R4_MARK, VI2_R5_MARK,
> > > >>>         VI2_R6_MARK, VI2_R7_MARK,
> > > >>>
> > > >>> Scenarios
> > > >>> 1: Say we connect a 8-bit camera just  with the G pins - YDS has to be
> > > >>> 1 for 8-bit YCbCr
> > > >>> 2: Say we connect a 8-bit camera just with the R pins - YDS has to be
> > > >>> 0 for 8-bit YCbCr
> > > >>> 3: Now say we use G2-G7 along with R0 and R1 pins to connect a 8 bit
> > > >>> camera - YDS has to be 1 for 8-bit camera
> > > >>>
> > > >>> And looking at the Gen1 description of YDS bit, having a combination
> > > >>> of B and G is not a valid case.
> > > >>
> > > >> Scenario 3 is indeed not supported. But G[1:0] and B[7:2] (= DATA[9:2])
> > > >> could work when using 10-bit YCbCr.
> > > >>
> > > >>> So my vote is to have a property in the endpoint to say if YDS has to
> > > >>> be enabled as done in my first version of the patch.
> > > >>
> > > >> "YDS" is not a generic property, "data-shift" is.
> > > >
> > > > Agreed, we want something standard.
> > >
> > > How do we proceed on this ?
> >
> > I may have lost track of the discussion here. Would a bus-width of 18 or
> > 24, like mentioned below, be enough to solve the problem, or do we need
> > something else ?
> >
> Sorry maybe I miss-read your email, are you suggesting me to set the
> YDS bit to1 if bus-width=18/24 ?
>
> On the RZ/G1H parallel port for VIN2 interface the bus-width=8 since
> just the VI2_Gx pins are used YDS has to be set to 1 for it to work.
>
Gentle ping.

Cheers,
Prabhakar
>
> > > >> Now, how do you specify in DT that RGB-666 mode is to be used?
> > > >> "bus-width = <18>"?
> > > >> That won't work with the (so far theoretical) case where both contiguous
> > > >> and sparse variants are supported by the hardware.  And "data-shift"
> > > >> won't help here.
> > > >>
> > > >> Am I overdesigning? ;-)
> > > >
> > > > If bus-width = <18>, VIN would know know that the 6 MSBs of each 8-bit
> > > > subset are used, as it doesn't support any other option. There's no need
> > > > for data-shift or any other property, as there's nothing to configure
> > > > :-) We could even set bus-width = <24>, it wouldn't make a difference.
> > >
> > > Thank you for jumping Laurent :)
> >
> > --
> > Regards,
> >
> > Laurent Pinchart