Re: [PATCH v5] perf test: Introduce script for Arm CoreSight testing

[Mathieu Poirier]

Hi Leo,

On Tue, Aug 18, 2020 at 01:49:27PM +0800, Leo Yan wrote:
> We need a simple method to test Perf with Arm CoreSight drivers, this
> could be used for smoke testing when new patch is coming for perf or
> CoreSight drivers, and we also can use the test to confirm if the
> CoreSight has been enabled successfully on new platforms.
> 
> This patch introduces the shell script test_arm_coresight.sh which is
> under the 'pert test' framework.  This script provides three testing
> scenarios:
> 
> Test scenario 1: traverse all possible paths between source and sink
> 
> For traversing possible paths, simply to say, the testing rationale
> is source oriented testing, it traverses every source (now only refers
> to ETM device) and test its all possible sinks.  To search the complete
> paths from one specific source to its sinks, this patch relies on the
> sysfs '/sys/bus/coresight/devices/devX/out:Y' for depth-first search
> (DFS) for iteration connected device nodes, if the output device is
> detected as a sink device (the script will exclude TPIU device which can
> not be supported for perf PMU), then it will test trace data recording
> and decoding for it.
> 
> The script runs three output testings for every trace data:
> - Test branch samples dumping with 'perf script' command;
> - Test branch samples reporting with 'perf report' command;
> - Use option '--itrace=i1000i' to insert synthesized instructions events
>   and the script will check if perf can output the percentage value
>   successfully based on the instruction samples.
> 
> Test scenario 2: system-wide test
> 
> For system-wide testing, it passes option '-a' to perf tool to enable
> tracing on all CPUs, so it's hard to say which program will be traced.
> But perf tool itself contributes much overload in this case, so it will
> parse trace data and check if process 'perf' can be detected or not.
> 
> Test scenario 3: snapshot mode test.
> 
> For snapshot mode testing, it uses 'dd' command to launch a long running
> program, so this can give chance to send signal -USR2; it will check the
> captured trace data contains 'dd' related thread info or not.
> 
> If any test fails, it will report failure and directly exit with error.
> This test will be only applied on a platform with PMU event 'cs_etm//',
> otherwise will skip the testing.
> 
> Below is detailed usage for it:
> 
>   # cd $linux/tools/perf  -> This is important so can use shell script
>   # perf test list
>     [...]
>     65: probe libc's inet_pton & backtrace it with ping
>     66: Check Arm CoreSight trace data recording and branch samples
>     67: Check open filename arg using perf trace + vfs_getname
>     68: Zstd perf.data compression/decompression
>     69: Add vfs_getname probe to get syscall args filenames
>     70: Use vfs_getname probe to get syscall args filenames
> 
>   # perf test 66
>     66: Check Arm CoreSight trace data recording and branch samples: Ok
> 
> Signed-off-by: Leo Yan <leo.yan@xxxxxxxxxx>
> ---
> 
> Changes in v5:
> - Fixed testing name to system-wide testing (Suzuki);
> - Used 'enable_sink' existence to check if the device is a sink (Suzuki);
> - Excluded TPIU from sink devices;
> - Fixed Misleading output (Suzuki);
> - Removed '--per-thread' option from snapshot testing (Suzuki).
> 
>  tools/perf/tests/shell/test_arm_coresight.sh | 175 +++++++++++++++++++
>  1 file changed, 175 insertions(+)
>  create mode 100755 tools/perf/tests/shell/test_arm_coresight.sh
> 
> diff --git a/tools/perf/tests/shell/test_arm_coresight.sh b/tools/perf/tests/shell/test_arm_coresight.sh
> new file mode 100755
> index 000000000000..8696bb5df45a
> --- /dev/null
> +++ b/tools/perf/tests/shell/test_arm_coresight.sh
> @@ -0,0 +1,175 @@
> +#!/bin/sh
> +# Check Arm CoreSight trace data recording and branch samples
> +
> +# Uses the 'perf record' to record trace data with Arm CoreSight sinks;
> +# then verify if there have any branch samples and instruction samples
> +# are generated by CoreSight with 'perf script' and 'perf report'
> +# commands.
> +
> +# SPDX-License-Identifier: GPL-2.0
> +# Leo Yan <leo.yan@xxxxxxxxxx>, 2020
> +
> +perfdata=$(mktemp /tmp/__perf_test.perf.data.XXXXX)
> +file=$(mktemp /tmp/temporary_file.XXXXX)
> +
> +skip_if_no_cs_etm_event() {
> +	perf list | grep -q 'cs_etm//' && return 0
> +
> +	# cs_etm event doesn't exist
> +	return 2
> +}
> +
> +skip_if_no_cs_etm_event || exit 2
> +
> +record_touch_file() {
> +	echo "Recording trace (only user mode) with path: CPU$2 => $1"
> +	rm -f $file
> +	perf record -o ${perfdata} -e cs_etm/@$1/u --per-thread \
> +		-- taskset -c $2 touch $file
> +}
> +
> +perf_script_branch_samples() {
> +	echo "Looking at perf.data file for dumping branch samples:"
> +
> +	# Below is an example of the branch samples dumping:
> +	#   touch  6512          1         branches:u:      ffffb220824c strcmp+0xc (/lib/aarch64-linux-gnu/ld-2.27.so)
> +	#   touch  6512          1         branches:u:      ffffb22082e0 strcmp+0xa0 (/lib/aarch64-linux-gnu/ld-2.27.so)
> +	#   touch  6512          1         branches:u:      ffffb2208320 strcmp+0xe0 (/lib/aarch64-linux-gnu/ld-2.27.so)
> +	perf script -F,-time -i ${perfdata} | \
> +		egrep " +$1 +[0-9]+ .* +branches:([u|k]:)? +"
> +}
> +
> +perf_report_branch_samples() {
> +	echo "Looking at perf.data file for reporting branch samples:"
> +
> +	# Below is an example of the branch samples reporting:
> +	#   73.04%    73.04%  touch    libc-2.27.so      [.] _dl_addr
> +	#    7.71%     7.71%  touch    libc-2.27.so      [.] getenv
> +	#    2.59%     2.59%  touch    ld-2.27.so        [.] strcmp
> +	perf report --stdio -i ${perfdata} | \
> +		egrep " +[0-9]+\.[0-9]+% +[0-9]+\.[0-9]+% +$1 "
> +}
> +
> +perf_report_instruction_samples() {
> +	echo "Looking at perf.data file for instruction samples:"
> +
> +	# Below is an example of the instruction samples reporting:
> +	#   68.12%  touch    libc-2.27.so   [.] _dl_addr
> +	#    5.80%  touch    libc-2.27.so   [.] getenv
> +	#    4.35%  touch    ld-2.27.so     [.] _dl_fixup
> +	perf report --itrace=i1000i --stdio -i ${perfdata} | \
> +		egrep " +[0-9]+\.[0-9]+% +$1"
> +}
> +
> +arm_cs_iterate_devices() {
> +	for dev in $1/connections/out\:*; do
> +
> +		# Skip testing if it's not a directory
> +		! [ -d $dev ] && continue;
> +
> +		# Read out its symbol link file name
> +		path=`readlink -f $dev`
> +
> +		# Extract device name from path, e.g.
> +		#   path = '/sys/devices/platform/20010000.etf/tmc_etf0'
> +		#     `> device_name = 'tmc_etf0'
> +		device_name=`echo $path | awk -F/ '{print $(NF)}'`
> +
> +
> +		# If the node of "enable_sink" is existed under the device path, this
> +		# means the device is a sink device.  Need to exclude 'tpiu' since it
> +		# cannot support perf PMU.
> +		echo $device_name | egrep -q -v "tpiu"
> +		if [ $? -eq 0 -a -e "$path/enable_sink" ]; then
> +
> +			pmu_dev="/sys/bus/event_source/devices/cs_etm/sinks/$device_name"
> +
> +			# Exit if the sink device is supported by PMU or not
> +			if ! [ -f $pmu_dev ]; then
> +				echo "PMU doesn't support $pmu_dev"
> +				exit 1
> +			fi
> +
> +			record_touch_file $device_name $2 &&
> +				perf_script_branch_samples touch &&
> +				perf_report_branch_samples touch &&
> +				perf_report_instruction_samples touch

Did you want to have an extra tab after the first line?  I think it makes the
code harder to read, but that's a personal opinion. 

> +
> +			err=$?
> +
> +			# Exit when find failure
> +			[ $err != 0 ] && exit $err

If a problem occurs ${perfdata} and ${file} are not removed.  The same is true
in several instances below.

Thanks,
Mathieu

> +
> +			rm -f ${perfdata}
> +			rm -f ${file}
> +		fi
> +
> +		arm_cs_iterate_devices $dev $2
> +	done
> +}
> +
> +arm_cs_etm_traverse_path_test() {
> +	# Iterate for every ETM device
> +	for dev in /sys/bus/coresight/devices/etm*; do
> +
> +		# Find the ETM device belonging to which CPU
> +		cpu=`cat $dev/cpu`
> +
> +		echo $dev
> +		echo $cpu
> +
> +		# Use depth-first search (DFS) to iterate outputs
> +		arm_cs_iterate_devices $dev $cpu
> +	done
> +}
> +
> +arm_cs_etm_system_wide_test() {
> +	echo "Recording trace with system wide mode"
> +	perf record -o ${perfdata} -e cs_etm// -a -- ls
> +
> +	perf_script_branch_samples perf &&
> +	perf_report_branch_samples perf &&
> +	perf_report_instruction_samples perf
> +
> +	err=$?
> +
> +	# Exit when find failure
> +	[ $err != 0 ] && exit $err
> +
> +	rm -f ${perfdata}
> +	rm -f ${file}
> +}
> +
> +arm_cs_etm_snapshot_test() {
> +	echo "Recording trace with snapshot mode"
> +	perf record -o ${perfdata} -e cs_etm// -S \
> +		-- dd if=/dev/zero of=/dev/null &
> +	PERFPID=$!
> +
> +	# Wait for perf program
> +	sleep 1
> +
> +	# Send signal to snapshot trace data
> +	kill -USR2 $PERFPID
> +
> +	# Stop perf program
> +	kill $PERFPID
> +	wait $PERFPID
> +
> +	perf_script_branch_samples dd &&
> +	perf_report_branch_samples dd &&
> +	perf_report_instruction_samples dd
> +
> +	err=$?
> +
> +	# Exit when find failure
> +	[ $err != 0 ] && exit $err
> +
> +	rm -f ${perfdata}
> +	rm -f ${file}
> +}
> +
> +arm_cs_etm_traverse_path_test
> +arm_cs_etm_system_wide_test
> +arm_cs_etm_snapshot_test
> +exit 0
> -- 
> 2.17.1
>