Re: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix driving parameter

From: Bjorn Helgaas
Date: Fri Sep 11 2020 - 12:55:26 EST

Next message: Krzysztof Kozlowski: "[PATCH 1/3] Documentation: Update paths of Samsung S3C machine files"
Previous message: Marco Felsch: "[PATCH 2/3] mtd: spi-nor: sst: add missing write_enable"
In reply to: 吳昊澄 Ricky: "RE: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix driving parameter"
Next in thread: 吳昊澄 Ricky: "RE: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix driving parameter"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Fri, Sep 11, 2020 at 08:18:22AM +0000, 吳昊澄 Ricky wrote:
> > -----Original Message-----
> > From: Bjorn Helgaas [mailto:helgaas@xxxxxxxxxx]
> > Sent: Thursday, September 10, 2020 1:44 AM
> > To: 吳昊澄 Ricky
> > Cc: arnd@xxxxxxxx; gregkh@xxxxxxxxxxxxxxxxxxx; bhelgaas@xxxxxxxxxx;
> > ulf.hansson@xxxxxxxxxx; rui_feng@xxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > puranjay12@xxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx;
> > vailbhavgupta40@xxxxxxxxxx
> > Subject: Re: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix driving
> > parameter
> >
> > On Wed, Sep 09, 2020 at 07:10:19AM +0000, 吳昊澄 Ricky wrote:
> > > > -----Original Message-----
> > > > From: Bjorn Helgaas [mailto:helgaas@xxxxxxxxxx]
> > > > Sent: Wednesday, September 09, 2020 6:29 AM
> > > > To: 吳昊澄 Ricky
> > > > Cc: arnd@xxxxxxxx; gregkh@xxxxxxxxxxxxxxxxxxx; bhelgaas@xxxxxxxxxx;
> > > > ulf.hansson@xxxxxxxxxx; rui_feng@xxxxxxxxxxxxxx;
> > linux-kernel@xxxxxxxxxxxxxxx;
> > > > puranjay12@xxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx;
> > > > vailbhavgupta40@xxxxxxxxxx
> > > > Subject: Re: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix
> > driving
> > > > parameter
> > > >
> > > > On Mon, Sep 07, 2020 at 06:07:31PM +0800, ricky_wu@xxxxxxxxxxx wrote:
> > > > > From: Ricky Wu <ricky_wu@xxxxxxxxxxx>
> > > > >
> > > > > v4:
> > > > > split power down flow and power saving function to two patch
> > > > >
> > > > > v5:
> > > > > fix up modified change under the --- line
> > > >
> > > > Hehe, this came out *above* the "---" line :)
> > > >
> > > > > Add rts522a L1 sub-state support
> > > > > Save more power on rts5227 rts5249 rts525a rts5260
> > > > > Fix rts5260 driving parameter
> > > > >
> > > > > Signed-off-by: Ricky Wu <ricky_wu@xxxxxxxxxxx>
> > > > > ---
> > > > > drivers/misc/cardreader/rts5227.c | 112 +++++++++++++++++++++-
> > > > > drivers/misc/cardreader/rts5249.c | 145
> > > > ++++++++++++++++++++++++++++-
> > > > > drivers/misc/cardreader/rts5260.c | 28 +++---
> > > > > drivers/misc/cardreader/rtsx_pcr.h | 17 ++++
> > > > > 4 files changed, 283 insertions(+), 19 deletions(-)
> > > > >
> > > > > diff --git a/drivers/misc/cardreader/rts5227.c
> > > > b/drivers/misc/cardreader/rts5227.c
> > > > > index 747391e3fb5d..8859011672cb 100644
> > > > > --- a/drivers/misc/cardreader/rts5227.c
> > > > > +++ b/drivers/misc/cardreader/rts5227.c
> > > > > @@ -72,15 +72,80 @@ static void rts5227_fetch_vendor_settings(struct
> > > > rtsx_pcr *pcr)
> > > > >
> > > > > pci_read_config_dword(pdev, PCR_SETTING_REG2, &reg);
> > > > > pcr_dbg(pcr, "Cfg 0x%x: 0x%x\n", PCR_SETTING_REG2, reg);
> > > > > + if (rtsx_check_mmc_support(reg))
> > > > > + pcr->extra_caps |= EXTRA_CAPS_NO_MMC;
> > > > > pcr->sd30_drive_sel_3v3 = rtsx_reg_to_sd30_drive_sel_3v3(reg);
> > > > > if (rtsx_reg_check_reverse_socket(reg))
> > > > > pcr->flags |= PCR_REVERSE_SOCKET;
> > > > > }
> > > > >
> > > > > +static void rts5227_init_from_cfg(struct rtsx_pcr *pcr)
> > > > > +{
> > > > > + struct pci_dev *pdev = pcr->pci;
> > > > > + int l1ss;
> > > > > + u32 lval;
> > > > > + struct rtsx_cr_option *option = &pcr->option;
> > > > > +
> > > > > + l1ss = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_L1SS);
> > > > > + if (!l1ss)
> > > > > + return;
> > > > > +
> > > > > + pci_read_config_dword(pdev, l1ss + PCI_L1SS_CTL1, &lval);
> > > >
> > > > This looks a little problematic. PCI_L1SS_CTL1 is an architected
> > > > register in the ASPM L1 PM Substates capability, and its value may
> > > > change at runtime because drivers/pci/pcie/aspm.c manages it.
> > > >
> > > > It looks like the code below does device-specific configuration based
> > > > on the current PCI_L1SS_CTL1 value. But what happens if aspm.c
> > > > changes PCI_L1SS_CTL1 later?
> > >
> > > We are going to make sure and set the best configuration on the
> > > current time, if host change the capability later, it doesn't affect
> > > function, only affect a little power saving
> >
> > Why don't you unconditionally do the following?
> >
> > rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
> > rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
> > rtsx_set_dev_flag(pcr, PM_L1_1_EN);
> > rtsx_set_dev_flag(pcr, PM_L1_2_EN);
>
> Our power saving function have 2 different flow L1 and L1substate,
> so we need to check it for which flow we are going to
> Detail to see below reply
>
> > Let's assume the generic code in aspm.c has cleared all these bits:
> >
> > PCI_L1SS_CTL1_ASPM_L1_1
> > PCI_L1SS_CTL1_ASPM_L1_2
> > PCI_L1SS_CTL1_PCIPM_L1_1
> > PCI_L1SS_CTL1_PCIPM_L1_2
> >
> > in the L1 PM Substates capability.
> >
> > I think you are saying that if you *also* clear ASPM_L1_1_EN,
> > ASPM_L1_2_EN, PM_L1_1_EN, and PM_L1_2_EN in your device-specific
> > registers, it uses less power than if you set those device-specific
> > bits. Right?
> >
> > And moreover, I think you're saying that if aspm.c subsequently *sets*
> > some of those bits in the L1 PM Substates capability, those substates
> > *work* even though the device-specific ASPM_L1_1_EN, ASPM_L1_2_EN,
> > PM_L1_1_EN, and PM_L1_2_EN bits are not set. Right?
> >
> > I do not feel good about this as a general strategy. I think we
> > should program the device so the behavior is completely predictable,
> > regardless of the generic enable bits happened to be set at
> > probe-time.
> >
> > The current approach means that if we enable L1 substates after the
> > driver probe, the device is configured differently than if we enabled
> > L1 substates before probe. That's not a reliable way to operate it.
>
> Talk about our power saving function
> a) basic L1 power saving
> b) advance L1 power saving
> c) advance L1 substate power saving

I have no idea what the difference between "basic L1 power saving" and
"advance L1 power saving" is, so I assume those are device-specific
things. If not, please use the same terminology as the PCIe spec.

> at initial, we check pci port support L1 subs or not, if not we are
> going to b) otherwise going to c).

You're not checking whether the port *supports* L1 substates. You
would look at PCI_L1SS_CAP to learn that. You're looking at
PCI_L1SS_CTL1, which tells you whether L1 substates are *enabled*.

> Assume aspm.c change bit of L1 PM Substates capability after our
> driver probe, we are going to a)
>
> So far we did not see any platform change L1 PM Substates capability
> after our driver probe.

You should expect that aspm.c will change bits in the L1 PM *control*
register (PCI_L1SS_CTL1) after probe.

You might not actually see it change, depending on how you tested, but
you cannot rely on PCI_L1SS_CTL1 being constant. It may change based
on power/performance tradeoffs, e.g., whether the system is plugged
into AC power, whether it's idle, etc.

> > > > > + if (CHK_PCI_PID(pcr, 0x522A)) {
> > > > > + if (0 == (lval & 0x0F))
> > > > > + rtsx_pci_enable_oobs_polling(pcr);
> > > > > + else
> > > > > + rtsx_pci_disable_oobs_polling(pcr);
> > > > > + }
> > > > > +
> > > > > + if (lval & PCI_L1SS_CTL1_ASPM_L1_1)
> > > > > + rtsx_set_dev_flag(pcr, ASPM_L1_1_EN);
> > > > > + else
> > > > > + rtsx_clear_dev_flag(pcr, ASPM_L1_1_EN);
> > > > > +
> > > > > + if (lval & PCI_L1SS_CTL1_ASPM_L1_2)
> > > > > + rtsx_set_dev_flag(pcr, ASPM_L1_2_EN);
> > > > > + else
> > > > > + rtsx_clear_dev_flag(pcr, ASPM_L1_2_EN);
> > > > > +
> > > > > + if (lval & PCI_L1SS_CTL1_PCIPM_L1_1)
> > > > > + rtsx_set_dev_flag(pcr, PM_L1_1_EN);
> > > > > + else
> > > > > + rtsx_clear_dev_flag(pcr, PM_L1_1_EN);
> > > > > +
> > > > > + if (lval & PCI_L1SS_CTL1_PCIPM_L1_2)
> > > > > + rtsx_set_dev_flag(pcr, PM_L1_2_EN);
> > > > > + else
> > > > > + rtsx_clear_dev_flag(pcr, PM_L1_2_EN);
> > > > > +
> > > > > + if (option->ltr_en) {
> > > > > + u16 val;
> > > > > +
> > > > > + pcie_capability_read_word(pcr->pci, PCI_EXP_DEVCTL2, &val);
> > > >
> > > > Same thing here. I don't think the PCI core currently changes
> > > > PCI_EXP_DEVCTL2 after boot, but it's not a good idea to assume it's
> > > > going to be constant.
> > > >
> > >
> > > The same reply
> > >
> > > > > + if (val & PCI_EXP_DEVCTL2_LTR_EN) {
> > > > > + option->ltr_enabled = true;
> > > > > + option->ltr_active = true;
> > > > > + rtsx_set_ltr_latency(pcr, option->ltr_active_latency);
> > > > > + } else {
> > > > > + option->ltr_enabled = false;
> > > > > + }
> > > > > + }
> > > > > +
> > > > > + if (rtsx_check_dev_flag(pcr, ASPM_L1_1_EN | ASPM_L1_2_EN
> > > > > + | PM_L1_1_EN | PM_L1_2_EN))
> > > > > + option->force_clkreq_0 = false;
> > > > > + else
> > > > > + option->force_clkreq_0 = true;
> > > > > +
> > > > > +}
> > > >
> > > > ------Please consider the environment before printing this e-mail.

Next message: Krzysztof Kozlowski: "[PATCH 1/3] Documentation: Update paths of Samsung S3C machine files"
Previous message: Marco Felsch: "[PATCH 2/3] mtd: spi-nor: sst: add missing write_enable"
In reply to: 吳昊澄 Ricky: "RE: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix driving parameter"
Next in thread: 吳昊澄 Ricky: "RE: [PATCH v5 2/2] misc: rtsx: Add power saving functions and fix driving parameter"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]