Re: [RFC PATCH V3 09/21] mmc: sdhci: add UHS-II related definitions in headers

From: AKASHI Takahiro
Date: Tue Sep 15 2020 - 02:47:32 EST

Next message: Marek Szyprowski: "Re: [PATCH v3 08/16] irqchip/gic: Configure SGIs as standard interrupts"
Previous message: Bhaskar Chowdhury: "[PATCH v2] docs: fb: Remove the stale boot option for framebuffer i.e scrollback"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Adrian,

On Fri, Aug 21, 2020 at 05:04:16PM +0300, Adrian Hunter wrote:
> On 10/07/20 2:10 pm, Ben Chuang wrote:
> > From: AKASHI Takahiro <takahiro.akashi@xxxxxxxxxx>
> >
> > Add UHS-II related definitions in shdci.h and sdhci-uhs2.h.
> >
> > Signed-off-by: Ben Chuang <ben.chuang@xxxxxxxxxxxxxxxxxxx>
> > Signed-off-by: AKASHI Takahiro <takahiro.akashi@xxxxxxxxxx>
> > ---
> > drivers/mmc/host/sdhci-uhs2.h | 215 ++++++++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci.h | 91 +++++++++++++-
> > 2 files changed, 305 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> >
> > diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
> > new file mode 100644
> > index 000000000000..a7f53f95d69a
> > --- /dev/null
> > +++ b/drivers/mmc/host/sdhci-uhs2.h
> > @@ -0,0 +1,215 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller
> > + * Interface driver
> > + *
> > + * Header file for Host Controller UHS2 related registers and I/O accessors.
> > + *
> > + * Copyright (C) 2014 Intel Corp, All Rights Reserved.
> > + */
> > +#ifndef __SDHCI_UHS2_H
> > +#define __SDHCI_UHS2_H
> > +
> > +#include <linux/mmc/host.h>
> > +#include <linux/mmc/core.h>
> > +#include <linux/mmc/uhs2.h>
>
> These includes should not be here unless this file needs them, which doesn't
> look like it.

Okay.

> Wouldn't hurt to make use of BIT and GENMASK macros since this is a new file.

Will try to convert all.

> > +
> > +/*
> > + * UHS-II Controller registers
> > + * 0x74 preset in sdhci.h
> > + * 0x80
> > + * 0x84-0xB4
> > + * 0xB8-0xCF
> > + * 0xE0-0xE7
> > + */
> > +/* UHS2 */
> > +#define SDHCI_UHS2_BLOCK_SIZE 0x80
> > +#define SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \
> > + ((((dma) & 0x7) << 12) | ((blksz) & 0xFFF))
> > +
> > +#define SDHCI_UHS2_BLOCK_COUNT 0x84
> > +
> > +#define SDHCI_UHS2_CMD_PACKET 0x88
> > +#define SDHCI_UHS2_CMD_PACK_MAX_LEN 20
> > +
> > +#define SDHCI_UHS2_TRANS_MODE 0x9C
> > +#define SDHCI_UHS2_TRNS_DMA 0x0001
> > +#define SDHCI_UHS2_TRNS_BLK_CNT_EN 0x0002
> > +#define SDHCI_UHS2_TRNS_DATA_TRNS_WRT 0x0010
> > +#define SDHCI_UHS2_TRNS_BLK_BYTE_MODE 0x0020
> > +#define SDHCI_UHS2_TRNS_RES_R5 0x0040
> > +#define SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN 0x0080
> > +#define SDHCI_UHS2_TRNS_RES_INT_DIS 0x0100
> > +#define SDHCI_UHS2_TRNS_WAIT_EBSY 0x4000
> > +#define SDHCI_UHS2_TRNS_2L_HD 0x8000
> > +
> > +#define SDHCI_UHS2_COMMAND 0x9E
> > +#define SDHCI_UHS2_COMMAND_SUB_CMD 0x0004
> > +#define SDHCI_UHS2_COMMAND_DATA 0x0020
> > +#define SDHCI_UHS2_COMMAND_TRNS_ABORT 0x0040
> > +#define SDHCI_UHS2_COMMAND_CMD12 0x0080
> > +#define SDHCI_UHS2_COMMAND_DORMANT 0x00C0
> > +#define SDHCI_UHS2_COMMAND_PACK_LEN_MASK 0x1F00
> > +#define SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT 8
> > +
> > +#define SDHCI_UHS2_RESPONSE 0xA0
> > +#define SDHCI_UHS2_RESPONSE_MAX_LEN 20
> > +
> > +#define SDHCI_UHS2_MSG_SELECT 0xB4
> > +#define SDHCI_UHS2_MSG_SELECT_CURR 0x0
> > +#define SDHCI_UHS2_MSG_SELECT_ONE 0x1
> > +#define SDHCI_UHS2_MSG_SELECT_TWO 0x2
> > +#define SDHCI_UHS2_MSG_SELECT_THREE 0x3
> > +
> > +#define SDHCI_UHS2_MSG 0xB8
> > +
> > +#define SDHCI_UHS2_DEV_INT_STATUS 0xBC
> > +
> > +#define SDHCI_UHS2_DEV_SELECT 0xBE
> > +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK 0x0F
> > +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN 0x80
> > +
> > +#define SDHCI_UHS2_DEV_INT_CODE 0xBF
> > +
> > +#define SDHCI_UHS2_SW_RESET 0xC0
> > +#define SDHCI_UHS2_SW_RESET_FULL 0x0001
> > +#define SDHCI_UHS2_SW_RESET_SD 0x0002
> > +
> > +#define SDHCI_UHS2_TIMER_CTRL 0xC2
> > +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT 4
> > +
> > +#define SDHCI_UHS2_ERR_INT_STATUS 0xC4
> > +#define SDHCI_UHS2_ERR_INT_STATUS_EN 0xC8
> > +#define SDHCI_UHS2_ERR_INT_SIG_EN 0xCC
> > +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER 0x00000001
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RES 0x00000002
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP 0x00000004
> > +#define SDHCI_UHS2_ERR_INT_STATUS_CRC 0x00000008
> > +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME 0x00000010
> > +#define SDHCI_UHS2_ERR_INT_STATUS_TID 0x00000020
> > +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER 0x00000080
> > +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY 0x00000100
> > +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA 0x00008000
> > +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT 0x00010000
> > +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT 0x00020000
> > +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR 0x08000000
> > +#define SDHCI_UHS2_ERR_INT_STATUS_MASK \
> > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \
> > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \
> > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \
> > + SDHCI_UHS2_ERR_INT_STATUS_TID | \
> > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \
> > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT | \
> > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> > +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK \
> > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES | \
> > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \
> > + SDHCI_UHS2_ERR_INT_STATUS_TID | \
> > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT)
> > +/* CRC Error occurs during a packet receiving */
> > +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK \
> > + (SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \
> > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \
> > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \
> > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \
> > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \
> > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT)
> > +
> > +#define SDHCI_UHS2_SET_PTR 0xE0
> > +#define SDHCI_UHS2_GEN_SET_POWER_LOW 0x0001
> > +#define SDHCI_UHS2_GEN_SET_N_LANES_POS 8
> > +#define SDHCI_UHS2_GEN_SET_2L_FD_HD 0x0
> > +#define SDHCI_UHS2_GEN_SET_2D1U_FD 0x2
> > +#define SDHCI_UHS2_GEN_SET_1D2U_FD 0x3
> > +#define SDHCI_UHS2_GEN_SET_2D2U_FD 0x4
> > +
> > +#define SDHCI_UHS2_PHY_SET_SPEED_POS 6
> > +#define SDHCI_UHS2_PHY_SET_HIBER_EN 0x00008000
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK 0x000F0000
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS 16
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK 0x00F00000
> > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS 20
> > +
> > +#define SDHCI_UHS2_TRAN_SET_N_FCU_MASK 0x0000FF00
> > +#define SDHCI_UHS2_TRAN_SET_N_FCU_POS 8
> > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK 0x00030000
> > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS 16
> > +
> > +#define SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK 0x000000FF
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_PTR 0xE2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_OFFSET 0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK 0x0000000F
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK 0x000000F0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap) ((gap) * 360)
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK 0x00003F00
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT 8
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD 1
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD 2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD 4
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD 8
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64 0x00004000
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BOOT 0x00008000
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK 0x00030000
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT 16
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV 0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB 1
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV 2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK 0x003C0000
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT 18
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK 0x00C00000
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT 22
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P 0
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING 1
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB 2
> > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING 3
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_OFFSET 4
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK 0x0000003F
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK 0x000000C0
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT 6
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A 0
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B 1
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK 0x000F0000
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT 16
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK 0x00F00000
> > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT 20
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET 8
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK 0x0000003F
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK 0x0000FF00
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT 8
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK 0x00070000
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT 16
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK 0xFFF00000
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT 20
> > +
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET 12
> > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK 0x000000FF
> > +
> > +#define SDHCI_UHS2_TEST_PTR 0xE4
> > +#define SDHCI_UHS2_TEST_ERR_HEADER 0x00000001
> > +#define SDHCI_UHS2_TEST_ERR_RES 0x00000002
> > +#define SDHCI_UHS2_TEST_ERR_RETRY_EXP 0x00000004
> > +#define SDHCI_UHS2_TEST_ERR_CRC 0x00000008
> > +#define SDHCI_UHS2_TEST_ERR_FRAME 0x00000010
> > +#define SDHCI_UHS2_TEST_ERR_TID 0x00000020
> > +#define SDHCI_UHS2_TEST_ERR_UNRECOVER 0x00000080
> > +#define SDHCI_UHS2_TEST_ERR_EBUSY 0x00000100
> > +#define SDHCI_UHS2_TEST_ERR_ADMA 0x00008000
> > +#define SDHCI_UHS2_TEST_ERR_RES_TIMEOUT 0x00010000
> > +#define SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT 0x00020000
> > +#define SDHCI_UHS2_TEST_ERR_VENDOR 0x08000000
> > +
> > +#define SDHCI_UHS2_EMBED_CTRL 0xE6
> > +#define SDHCI_UHS2_VENDOR 0xE8
> > +
> > +void sdhci_uhs2_reset(struct sdhci_host *host, u16 mask);
> > +void sdhci_uhs2_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set);
> > +
> > +#endif /* __SDHCI_UHS2_H */
> > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> > index 0008bbd27127..ecf55394ea46 100644
> > --- a/drivers/mmc/host/sdhci.h
> > +++ b/drivers/mmc/host/sdhci.h
> > @@ -43,8 +43,27 @@
> > #define SDHCI_TRNS_READ 0x10
> > #define SDHCI_TRNS_MULTI 0x20
> >
> > +/*
> > + * Defined in Host Version 4.10.
> > + * 1 - R5 (SDIO)
> > + * 0 - R1 (Memory)
> > + */
> > +#define SDHCI_TRNS_RES_TYPE 0x40
> > +#define SDHCI_TRNS_RES_ERR_CHECK 0x80
> > +#define SDHCI_TRNS_RES_INT_DIS 0x0100
> > +
> > #define SDHCI_COMMAND 0x0E
> > #define SDHCI_CMD_RESP_MASK 0x03
> > +
> > +/*
> > + * Host Version 4.10 adds this bit to distinguish a main command or
> > + * sub command.
> > + * CMD53(SDIO) - main command
> > + * CMD52(SDIO) - sub command which doesn't have data block or doesn't
> > + * indicate busy.
> > + */
> > +#define SDHCI_CMD_SUB_CMD 0x04
> > +
> > #define SDHCI_CMD_CRC 0x08
> > #define SDHCI_CMD_INDEX 0x10
> > #define SDHCI_CMD_DATA 0x20
> > @@ -60,11 +79,19 @@
> >
> > #define SDHCI_RESPONSE 0x10
> >
> > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET 0x10
> > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE 4
> > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET 0x18
> > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE 8
> > +
> > #define SDHCI_BUFFER 0x20
> >
> > #define SDHCI_PRESENT_STATE 0x24
> > #define SDHCI_CMD_INHIBIT 0x00000001
> > #define SDHCI_DATA_INHIBIT 0x00000002
> > +
> > +#define SDHCI_DATA_HIGH_LVL_MASK 0x000000F0
> > +
> > #define SDHCI_DOING_WRITE 0x00000100
> > #define SDHCI_DOING_READ 0x00000200
> > #define SDHCI_SPACE_AVAILABLE 0x00000400
> > @@ -80,6 +107,13 @@
> > #define SDHCI_DATA_0_LVL_MASK 0x00100000
> > #define SDHCI_CMD_LVL 0x01000000
> >
> > +#define SDHCI_HOST_REGULATOR_STABLE 0x02000000
> > +#define SDHCI_CMD_NOT_ISSUE_ERR 0x08000000
> > +#define SDHCI_SUB_CMD_STATUS 0x10000000
> > +#define SDHCI_UHS2_IN_DORMANT_STATE 0x20000000
> > +#define SDHCI_UHS2_LANE_SYNC 0x40000000
> > +#define SDHCI_UHS2_IF_DETECT 0x80000000
> > +
> > #define SDHCI_HOST_CONTROL 0x28
> > #define SDHCI_CTRL_LED 0x01
> > #define SDHCI_CTRL_4BITBUS 0x02
> > @@ -100,6 +134,11 @@
> > #define SDHCI_POWER_300 0x0C
> > #define SDHCI_POWER_330 0x0E
> >
> > +/* VDD2 - UHS2 */
> > +#define SDHCI_VDD2_POWER_ON 0x10
> > +#define SDHCI_VDD2_POWER_180 0xA0
> > +#define SDHCI_VDD2_POWER_120 0x80
> > +
> > #define SDHCI_BLOCK_GAP_CONTROL 0x2A
> >
> > #define SDHCI_WAKE_UP_CONTROL 0x2B
> > @@ -110,7 +149,7 @@
> > #define SDHCI_CLOCK_CONTROL 0x2C
> > #define SDHCI_DIVIDER_SHIFT 8
> > #define SDHCI_DIVIDER_HI_SHIFT 6
> > -#define SDHCI_DIV_MASK 0xFF
> > +#define SDHCI_DIV_MASK 0xFF
> > #define SDHCI_DIV_MASK_LEN 8
> > #define SDHCI_DIV_HI_MASK 0x300
> > #define SDHCI_PROG_CLOCK_MODE 0x0020
> > @@ -139,6 +178,10 @@
> > #define SDHCI_INT_CARD_REMOVE 0x00000080
> > #define SDHCI_INT_CARD_INT 0x00000100
> > #define SDHCI_INT_RETUNE 0x00001000
> > +
> > +/* Host Version 4.10 */
> > +#define SDHCI_INT_FX_EVENT 0x00002000
> > +
> > #define SDHCI_INT_CQE 0x00004000
> > #define SDHCI_INT_ERROR 0x00008000
> > #define SDHCI_INT_TIMEOUT 0x00010000
> > @@ -152,6 +195,9 @@
> > #define SDHCI_INT_AUTO_CMD_ERR 0x01000000
> > #define SDHCI_INT_ADMA_ERROR 0x02000000
> >
> > +/* Host Version 4.0 */
> > +#define SDHCI_INT_RESPONSE_ERROR 0x08000000
> > +
> > #define SDHCI_INT_NORMAL_MASK 0x00007FFF
> > #define SDHCI_INT_ERROR_MASK 0xFFFF8000
> >
> > @@ -178,6 +224,9 @@
> > #define SDHCI_AUTO_CMD_END_BIT 0x00000008
> > #define SDHCI_AUTO_CMD_INDEX 0x00000010
> >
> > +/* Host Version 4.10 */
> > +#define SDHCI_ACMD_RESPONSE_ERROR 0x0020
> > +
> > #define SDHCI_HOST_CONTROL2 0x3E
> > #define SDHCI_CTRL_UHS_MASK 0x0007
> > #define SDHCI_CTRL_UHS_SDR12 0x0000
> > @@ -186,6 +235,7 @@
> > #define SDHCI_CTRL_UHS_SDR104 0x0003
> > #define SDHCI_CTRL_UHS_DDR50 0x0004
> > #define SDHCI_CTRL_HS400 0x0005 /* Non-standard */
> > +#define SDHCI_CTRL_UHS_2 0x0007 /* UHS-2 */
> > #define SDHCI_CTRL_VDD_180 0x0008
> > #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
> > #define SDHCI_CTRL_DRV_TYPE_B 0x0000
> > @@ -194,9 +244,12 @@
> > #define SDHCI_CTRL_DRV_TYPE_D 0x0030
> > #define SDHCI_CTRL_EXEC_TUNING 0x0040
> > #define SDHCI_CTRL_TUNED_CLK 0x0080
> > +#define SDHCI_CTRL_UHS2_INTERFACE_EN 0x0100 /* UHS-2 */
> > +#define SDHCI_CTRL_ADMA2_LEN_MODE 0x0400
> > #define SDHCI_CMD23_ENABLE 0x0800
> > #define SDHCI_CTRL_V4_MODE 0x1000
> > #define SDHCI_CTRL_64BIT_ADDR 0x2000
> > +#define SDHCI_CTRL_ASYNC_INT_EN 0x4000
> > #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
> >
> > #define SDHCI_CAPABILITIES 0x40
> > @@ -217,11 +270,13 @@
> > #define SDHCI_CAN_VDD_180 0x04000000
> > #define SDHCI_CAN_64BIT_V4 0x08000000
> > #define SDHCI_CAN_64BIT 0x10000000
> > +#define SDHCI_CAN_ASYNC_INT 0x20000000
> >
> > #define SDHCI_CAPABILITIES_1 0x44
> > #define SDHCI_SUPPORT_SDR50 0x00000001
> > #define SDHCI_SUPPORT_SDR104 0x00000002
> > #define SDHCI_SUPPORT_DDR50 0x00000004
> > +#define SDHCI_SUPPORT_UHS2 0x00000008 /* UHS-2 support */
> > #define SDHCI_DRIVER_TYPE_A 0x00000010
> > #define SDHCI_DRIVER_TYPE_C 0x00000020
> > #define SDHCI_DRIVER_TYPE_D 0x00000040
> > @@ -230,19 +285,28 @@
> > #define SDHCI_RETUNING_MODE_MASK GENMASK(15, 14)
> > #define SDHCI_CLOCK_MUL_MASK GENMASK(23, 16)
> > #define SDHCI_CAN_DO_ADMA3 0x08000000
> > +#define SDHCI_SUPPORT_VDD2_180 0x10000000 /* UHS-2 1.8V VDD2 */
> > +#define SDHCI_RSVD_FOR_VDD2 0x20000000 /* Rsvd for future VDD2 */
> > #define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */
> >
> > #define SDHCI_MAX_CURRENT 0x48
> > +#define SDHCI_MAX_CURRENT_1 0x4C
> > #define SDHCI_MAX_CURRENT_LIMIT GENMASK(7, 0)
> > #define SDHCI_MAX_CURRENT_330_MASK GENMASK(7, 0)
> > #define SDHCI_MAX_CURRENT_300_MASK GENMASK(15, 8)
> > #define SDHCI_MAX_CURRENT_180_MASK GENMASK(23, 16)
> > +#define SDHCI_MAX_CURRENT_VDD2_180_MASK GENMASK(7, 0) /* UHS2 */
> > #define SDHCI_MAX_CURRENT_MULTIPLIER 4
> >
> > /* 4C-4F reserved for more max current */
> >
> > #define SDHCI_SET_ACMD12_ERROR 0x50
> > +/* Host Version 4.10 */
> > +#define SDHCI_SET_ACMD_RESPONSE_ERROR 0x20
> > #define SDHCI_SET_INT_ERROR 0x52
> > +/* Host Version 4.10 */
> > +#define SDHCI_SET_INT_TUNING_ERROR 0x0400
> > +#define SDHCI_SET_INT_RESPONSE_ERROR 0x0800
> >
> > #define SDHCI_ADMA_ERROR 0x54
> >
> > @@ -259,10 +323,16 @@
> > #define SDHCI_PRESET_FOR_SDR104 0x6C
> > #define SDHCI_PRESET_FOR_DDR50 0x6E
> > #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
> > +
> > +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */
> > +/* UHS2 */
> > +#define SDHCI_PRESET_FOR_UHS2 0x74
> > #define SDHCI_PRESET_DRV_MASK GENMASK(15, 14)
> > #define SDHCI_PRESET_CLKGEN_SEL BIT(10)
> > #define SDHCI_PRESET_SDCLK_FREQ_MASK GENMASK(9, 0)
> >
> > +#define SDHCI_ADMA3_ADDRESS 0x78
> > +
> > #define SDHCI_SLOT_INT_STATUS 0xFC
> >
> > #define SDHCI_HOST_VERSION 0xFE
> > @@ -653,6 +723,25 @@ struct sdhci_ops {
> > void (*dump_vendor_regs)(struct sdhci_host *host);
> > };
> >
> > +struct sdhci_uhs2_ops {
> > + /* UHS-2 support */
> > + void (*reset)(struct sdhci_host *host, u16 mask);
> > + void (*set_timeout)(struct sdhci_host *host);
> > + void (*set_transfer_mode)(struct sdhci_host *host,
> > + struct mmc_command *cmd);
> > + void (*send_command)(struct sdhci_host *host,
> > + struct mmc_command *cmd);
> > + void (*finish_command)(struct sdhci_host *host);
> > + void (*do_set_ios)(struct sdhci_host *host, struct mmc_ios *ios);
> > + int (*do_detect_init)(struct sdhci_host *host);
> > + int (*do_set_reg)(struct sdhci_host *host, enum uhs2_act act);
> > + void (*irq)(struct sdhci_host *host);
> > + int (*add_host)(struct sdhci_host *host, u32 caps1);
> > + void (*remove_host)(struct sdhci_host *host, int dead);
> > +};
>
> Instead of this structure, please just add functions to sdhci_ops.

I think that one of your requirements is to purge all uhs2-related
code from sdhci.c and that the structure above meets it.

But I will try to move them to struct sdhci_ops if you really want.

-Takahiro Akashi

> > +
> > +extern struct sdhci_uhs2_ops sdhci_uhs2_ops;
> > +
> > #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
> >
> > static inline void sdhci_writel(struct sdhci_host *host, u32 val, int reg)
> >
>

Next message: Marek Szyprowski: "Re: [PATCH v3 08/16] irqchip/gic: Configure SGIs as standard interrupts"
Previous message: Bhaskar Chowdhury: "[PATCH v2] docs: fb: Remove the stale boot option for framebuffer i.e scrollback"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]