[PATCH 1/3] mtd: rawnand: Fix wrongful fallthrough NAND_ECC_SOFT

[Tudor Ambarus]

In case of valid HW ECC, where the fallback to SW ECC is not needed,
the mentioned commit breaks the "switch (ecc->placement)" statement,
but then wrongly falls through the "case NAND_ECC_SOFT" of the
parent "switch (ecc->mode)". This causes an -EINVAL in
nand_set_ecc_soft_ops(), because for the valid HW ECC cases
ecc->mode is set to NAND_ECC_HW, but the nand_set_ecc_soft_ops()
expects a NAND_ECC_SOFT mode, thus -EINVAL.

Move the fallback to SW ECC after the setting of the ECC on host ops.
With this, when a valid HW ECC is available, we break the
"switch (ecc->mode)" statement, and when a fallback to SW ECC is
needed, we fallthrough "case NAND_ECC_SOFT".

Fixes: d3f8ec8e979b ("mtd: rawnand: Separate the ECC engine type and the ECC byte placement")
Reported-by: Santiago Esteban <santiago.esteban@xxxxxxxxxxxxx>
Signed-off-by: Tudor Ambarus <tudor.ambarus@xxxxxxxxxxxxx>
---
 drivers/mtd/nand/raw/nand_base.c | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)

diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index d42832bedff5..bd30f6632fe2 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -5665,19 +5665,6 @@ static int nand_scan_tail(struct nand_chip *chip)
 				ecc->read_oob = nand_read_oob_syndrome;
 			if (!ecc->write_oob)
 				ecc->write_oob = nand_write_oob_syndrome;
-
-			if (mtd->writesize >= ecc->size) {
-				if (!ecc->strength) {
-					WARN(1, "Driver must set ecc.strength when using hardware ECC\n");
-					ret = -EINVAL;
-					goto err_nand_manuf_cleanup;
-				}
-				break;
-			}
-			pr_warn("%d byte HW ECC not possible on %d byte page size, fallback to SW ECC\n",
-				ecc->size, mtd->writesize);
-			ecc->engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-			ecc->algo = NAND_ECC_ALGO_HAMMING;
 			break;
 
 		default:
@@ -5686,6 +5673,19 @@ static int nand_scan_tail(struct nand_chip *chip)
 			ret = -EINVAL;
 			goto err_nand_manuf_cleanup;
 		}
+
+		if (mtd->writesize >= ecc->size) {
+			if (!ecc->strength) {
+				WARN(1, "Driver must set ecc.strength when using hardware ECC\n");
+				ret = -EINVAL;
+				goto err_nand_manuf_cleanup;
+			}
+			break;
+		}
+		pr_warn("%d byte HW ECC not possible on %d byte page size, fallback to SW ECC\n",
+			ecc->size, mtd->writesize);
+		ecc->engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+		ecc->algo = NAND_ECC_ALGO_HAMMING;
 		fallthrough;
 
 	case NAND_ECC_ENGINE_TYPE_SOFT:
-- 
2.25.1