Re: [PATCH v6 09/14] usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)

[Badhri Jagan Sridharan]

On Tue, Sep 15, 2020 at 6:20 AM Heikki Krogerus
<heikki.krogerus@xxxxxxxxxxxxxxx> wrote:
>
> On Mon, Aug 31, 2020 at 07:59:22PM -0700, Badhri Jagan Sridharan wrote:
> > PD 3.0 spec defines a new mechanism for power role swap called
> > Fast role swap. This change enables TCPM to support FRS when
> > acting as sink.
> >
> > Once the explicit contract is negotiated, sink port is
> > expected to query the source port for sink caps to
> > determine whether the source is FRS capable.
> > Bits 23 & 24 of fixed pdo of the sink caps from the source, when
> > set, indicates the current needed by the source when fast role
> > swap is in progress(Implicit contract phasae). 0 indicates that
> > the source does not support Fast Role Swap.
> >
> > Upon receiving the FRS signal from the source,
> > TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.
> >
> > 1. TCPM sends FRS PD message: FR_SWAP_SEND
> > 2. If response is not received within the expiry of
> >    SenderResponseTimer, Error recovery is triggered.:
> >    FR_SWAP_SEND_TIMEOUT
> > 3. Upon receipt of the accept message, TCPM waits for
> >    PSSourceOffTimer for PS_READY message from the partner:
> >    FR_SWAP_SNK_SRC_NEW_SINK_READY.
> >
> > TCPC is expected to autonomously turn on vbus once the FRS
> > signal is received and vbus voltage falls below vsafe5v within
> > tSrcFrSwap. This is different from traditional power role swap
> > where the vbus sourcing is turned on by TCPM.
> >
> > 4. By this time, TCPC most likely would have started to
> >    source vbus, TCPM waits for tSrcFrSwap to see  if the
> >    lower level TCPC driver signals TCPM_SOURCING_VBUS event:
> >    FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
> > 5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
> >    changes the CC pin from Rd to Rp. This is the end of fast
> >    role swap sequence and TCPM initiates the sequnce to negotiate
> >    explicit contract by transitioning into SRC_STARTUP after
> >    SwapSrcStart.
> >
> > The code is written based on the sequence described in "Figure 8-107:
> > Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
> > USB Power Delivery Specification Revision 3.0, Version 1.2.
> >
> > Signed-off-by: Badhri Jagan Sridharan <badhri@xxxxxxxxxx>
> > ---
> > Changes since v1:
> > - Changing patch version to v6 to fix version number confusion.
> > - Rebased on top of usb-next and resolved conflicts due to the below
> >   changes:
> >   3ed8e1c2ac99 usb: typec: tcpm: Migrate workqueue to RT priority for processing events
> >   6bbe2a90a0bb usb: typec: tcpm: During PR_SWAP, source caps should be sent only after tSwapSourceStart
> > - enable_frs sequence is now run as part of the same kthread that runs
> >   the state machines.
> > - Fixed the implicit fallthrough warning in the switch case for
> >   FR_SWAP_CANCEL case.
> > ---
> >  drivers/usb/typec/tcpm/tcpm.c | 217 +++++++++++++++++++++++++++++++++-
> >  include/linux/usb/pd.h        |  19 +--
> >  include/linux/usb/tcpm.h      |   8 +-
> >  include/linux/usb/typec.h     |  13 ++
> >  4 files changed, 245 insertions(+), 12 deletions(-)
> >
> > diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> > index 92806547f485..083e7af107b2 100644
> > --- a/drivers/usb/typec/tcpm/tcpm.c
> > +++ b/drivers/usb/typec/tcpm/tcpm.c
> > @@ -106,6 +106,13 @@
> >       S(VCONN_SWAP_TURN_ON_VCONN),            \
> >       S(VCONN_SWAP_TURN_OFF_VCONN),           \
> >                                               \
> > +     S(FR_SWAP_SEND),                        \
> > +     S(FR_SWAP_SEND_TIMEOUT),                \
> > +     S(FR_SWAP_SNK_SRC_TRANSITION_TO_OFF),                   \
> > +     S(FR_SWAP_SNK_SRC_NEW_SINK_READY),              \
> > +     S(FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED), \
> > +     S(FR_SWAP_CANCEL),                      \
> > +                                             \
> >       S(SNK_TRY),                             \
> >       S(SNK_TRY_WAIT),                        \
> >       S(SNK_TRY_WAIT_DEBOUNCE),               \
> > @@ -127,6 +134,9 @@
> >       S(GET_PPS_STATUS_SEND),                 \
> >       S(GET_PPS_STATUS_SEND_TIMEOUT),         \
> >                                               \
> > +     S(GET_SINK_CAP),                        \
> > +     S(GET_SINK_CAP_TIMEOUT),                \
> > +                                             \
> >       S(ERROR_RECOVERY),                      \
> >       S(PORT_RESET),                          \
> >       S(PORT_RESET_WAIT_OFF)
> > @@ -175,6 +185,8 @@ enum adev_actions {
> >  #define TCPM_CC_EVENT                BIT(0)
> >  #define TCPM_VBUS_EVENT              BIT(1)
> >  #define TCPM_RESET_EVENT     BIT(2)
> > +#define TCPM_FRS_EVENT               BIT(3)
> > +#define TCPM_SOURCING_VBUS   BIT(4)
> >
> >  #define LOG_BUFFER_ENTRIES   1024
> >  #define LOG_BUFFER_ENTRY_SIZE        128
> > @@ -184,6 +196,8 @@ enum adev_actions {
> >  #define SVID_DISCOVERY_MAX   16
> >  #define ALTMODE_DISCOVERY_MAX        (SVID_DISCOVERY_MAX * MODE_DISCOVERY_MAX)
> >
> > +#define GET_SINK_CAP_RETRY_MS        100
> > +
> >  struct pd_mode_data {
> >       int svid_index;         /* current SVID index           */
> >       int nsvids;
> > @@ -261,6 +275,8 @@ struct tcpm_port {
> >       struct kthread_work state_machine;
> >       struct hrtimer vdm_state_machine_timer;
> >       struct kthread_work vdm_state_machine;
> > +     struct hrtimer enable_frs_timer;
> > +     struct kthread_work enable_frs;
> >       bool state_machine_running;
> >
> >       struct completion tx_complete;
> > @@ -335,6 +351,12 @@ struct tcpm_port {
> >       /* port belongs to a self powered device */
> >       bool self_powered;
> >
> > +     /* FRS */
> > +     enum frs_typec_current frs_current;
>
> Do you use this member anywhere?
>
> I can't see anywhere it being used, but I think you should use it
> instead the one in port_caps.
Yes I started with having it here and then switched to port_caps
while forgetting this !
Have gone back to using the one here.

>
> > +     /* Sink caps have been queried */
> > +     bool sink_cap_done;
> > +
> >  #ifdef CONFIG_DEBUG_FS
> >       struct dentry *dentry;
> >       struct mutex logbuffer_lock;    /* log buffer access lock */
> > @@ -940,6 +962,16 @@ static void mod_vdm_delayed_work(struct tcpm_port *port, unsigned int delay_ms)
> >       }
> >  }
>
> <snip>
>
> > diff --git a/include/linux/usb/typec.h b/include/linux/usb/typec.h
> > index 9cb1bec94b71..2ec7451a14ab 100644
> > --- a/include/linux/usb/typec.h
> > +++ b/include/linux/usb/typec.h
> > @@ -204,6 +204,18 @@ struct typec_operations {
> >                            enum typec_port_type type);
> >  };
> >
> > +/*
> > + * Initial current capability of the new source when vSafe5V is applied during PD3.0 Fast Role Swap.
> > + * Based on "Table 6-14 Fixed Supply PDO - Sink" of "USB Power Delivery Specification Revision 3.0,
> > + * Version 1.2"
> > + */
> > +enum frs_typec_current {
> > +     FRS_NOT_SUPPORTED,
> > +     FRS_DEFAULT_POWER,
> > +     FRS_5V_1P5A,
> > +     FRS_5V_3A,
> > +};
> > +
> >  /*
> >   * struct typec_capability - USB Type-C Port Capabilities
> >   * @type: Supported power role of the port
> > @@ -226,6 +238,7 @@ struct typec_capability {
> >       int                     prefer_role;
> >       enum typec_accessory    accessory[TYPEC_MAX_ACCESSORY];
> >       unsigned int            orientation_aware:1;
> > +     enum frs_typec_current  frs_current;
>
> So forget about this. We can add it here if/when there is another
> driver that needs that. You already have that member in struct
> tcpm_port, so just use that for now.
>
> And you can also introduce enum frs_typec_current in tcpm.c for now.

Sure ! Done in v7.

>
> >       struct fwnode_handle    *fwnode;
> >       void                    *driver_data;
> > --
> > 2.28.0.402.g5ffc5be6b7-goog
>
> thanks,
>
> --
> heikki