[PATCH net-next v4 2/5] dt-bindings: net: renesas,ravb: Document internal clock delay properties

[Geert Uytterhoeven]

Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).

Add properties for configuring the internal MAC delays.
These properties are mandatory, even when specified as zero, to
distinguish between old and new DTBs.

Update the (bogus) example accordingly.

Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@xxxxxxxxx>
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
---
v4:
  - Add Reviewed-by,

v3:
  - Add Reviewed-by,

v2:
  - Replace "renesas,[rt]xc-delay-ps" by "[rt]x-internal-delay-ps",
  - Add "(bogus)" to the example update, to avoid people considering it
    a one-to-one conversion.
---
 .../devicetree/bindings/net/renesas,ravb.txt  | 29 ++++++++++---------
 1 file changed, 16 insertions(+), 13 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt
index 032b76f14f4fdb38..4a62dd11d5c488f4 100644
--- a/Documentation/devicetree/bindings/net/renesas,ravb.txt
+++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt
@@ -64,6 +64,18 @@ Optional properties:
 			 AVB_LINK signal.
 - renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is
 				 active-low instead of normal active-high.
+- rx-internal-delay-ps: Internal RX clock delay.
+			This property is mandatory and valid only on R-Car Gen3
+			and RZ/G2 SoCs.
+			Valid values are 0 and 1800.
+			A non-zero value is allowed only if phy-mode = "rgmii".
+			Zero is not supported on R-Car D3.
+- tx-internal-delay-ps: Internal TX clock delay.
+			This property is mandatory and valid only on R-Car H3,
+			M3-W, M3-W+, M3-N, V3M, and V3H, and RZ/G2M and RZ/G2N.
+			Valid values are 0 and 2000.
+			A non-zero value is allowed only if phy-mode = "rgmii".
+			Zero is not supported on R-Car V3H.
 
 Example:
 
@@ -105,8 +117,10 @@ Example:
 				  "ch24";
 		clocks = <&cpg CPG_MOD 812>;
 		power-domains = <&cpg>;
-		phy-mode = "rgmii-id";
+		phy-mode = "rgmii";
 		phy-handle = <&phy0>;
+		rx-internal-delay-ps = <0>;
+		tx-internal-delay-ps = <2000>;
 
 		pinctrl-0 = <&ether_pins>;
 		pinctrl-names = "default";
@@ -115,18 +129,7 @@ Example:
 		#size-cells = <0>;
 
 		phy0: ethernet-phy@0 {
-			rxc-skew-ps = <900>;
-			rxdv-skew-ps = <0>;
-			rxd0-skew-ps = <0>;
-			rxd1-skew-ps = <0>;
-			rxd2-skew-ps = <0>;
-			rxd3-skew-ps = <0>;
-			txc-skew-ps = <900>;
-			txen-skew-ps = <0>;
-			txd0-skew-ps = <0>;
-			txd1-skew-ps = <0>;
-			txd2-skew-ps = <0>;
-			txd3-skew-ps = <0>;
+			rxc-skew-ps = <1500>;
 			reg = <0>;
 			interrupt-parent = <&gpio2>;
 			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-- 
2.17.1