RE: [PATCH V2 2/2] ata: ahci: ceva: Update the driver to support xilinx GT phy
From: Piyush Mehta
Date: Wed Sep 23 2020 - 01:45:11 EST
Hello Philipp,
Thanks for review.
Regards,
Piyush Mehta
-----Original Message-----
From: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
Sent: Tuesday, September 22, 2020 5:36 PM
To: Piyush Mehta <piyushm@xxxxxxxxxx>; axboe@xxxxxxxxx; robh+dt@xxxxxxxxxx
Cc: linux-ide@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; git <git@xxxxxxxxxx>; Srinivas Goud <sgoud@xxxxxxxxxx>; Michal Simek <michals@xxxxxxxxxx>
Subject: Re: [PATCH V2 2/2] ata: ahci: ceva: Update the driver to support xilinx GT phy
On Tue, 2020-09-22 at 15:45 +0530, Piyush Mehta wrote:
> SATA controller used in Xilinx ZynqMP platform uses xilinx GT phy
> which has 4 GT lanes and can used by 4 peripherals at a time.
> SATA controller uses 1 GT phy lane among the 4 GT lanes. To configure
> the GT lane for SATA controller, the below sequence is expected.
>
> 1. Assert the SATA controller reset.
> 2. Configure the xilinx GT phy lane for SATA controller (phy_init).
> 3. De-assert the SATA controller reset.
> 4. Wait for PLL of the GT lane used by SATA to be locked (phy_power_on).
>
> The ahci_platform_enable_resources() by default does the phy_init()
> and phy_power_on() but the default sequence doesn't work with Xilinx
> platforms. Because of this reason, updated the driver to support the
> new sequence.
>
> Added is_rst_ctrl flag, for backward compatibility with the older
> sequence. If the reset controller is not available, then the SATA
> controller will configure with the older sequences.
>
> Signed-off-by: Piyush Mehta <piyush.mehta@xxxxxxxxxx>
> ---
> drivers/ata/ahci_ceva.c | 39 +++++++++++++++++++++++++++++++++++++--
> 1 file changed, 37 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c index
> b10fd4c..c704906 100644
> --- a/drivers/ata/ahci_ceva.c
> +++ b/drivers/ata/ahci_ceva.c
> @@ -12,6 +12,7 @@
> #include <linux/module.h>
> #include <linux/of_device.h>
> #include <linux/platform_device.h>
> +#include <linux/reset.h>
> #include "ahci.h"
>
> /* Vendor Specific Register Offsets */ @@ -87,6 +88,7 @@ struct
> ceva_ahci_priv {
> u32 axicc;
> bool is_cci_enabled;
> int flags;
> + struct reset_control *rst;
> };
>
> static unsigned int ceva_ahci_read_id(struct ata_device *dev, @@
> -194,7 +196,7 @@ static int ceva_ahci_probe(struct platform_device *pdev)
> struct ahci_host_priv *hpriv;
> struct ceva_ahci_priv *cevapriv;
> enum dev_dma_attr attr;
> - int rc;
> + int rc, i, is_rst_ctrl = 1;
>
> cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL);
> if (!cevapriv)
> @@ -202,14 +204,47 @@ static int ceva_ahci_probe(struct
> platform_device *pdev)
>
> cevapriv->ahci_pdev = pdev;
>
> + cevapriv->rst = devm_reset_control_get(&pdev->dev, NULL);
Please use devm_reset_control_get_optional_exclusive()
> + if (IS_ERR(cevapriv->rst)) {
> + if (PTR_ERR(cevapriv->rst) != -EPROBE_DEFER)
> + dev_err(&pdev->dev, "failed to get reset: %ld\n",
> + PTR_ERR(cevapriv->rst));
> + is_rst_ctrl = 0;
is_rst_ctrl will not be required then.
> + }
> +
> hpriv = ahci_platform_get_resources(pdev, 0);
> if (IS_ERR(hpriv))
> return PTR_ERR(hpriv);
> + if (is_rst_ctrl)
> + rc = ahci_platform_enable_clks(hpriv);
> + else
> + rc = ahci_platform_enable_resources(hpriv);
>
> - rc = ahci_platform_enable_resources(hpriv);
> if (rc)
> return rc;
>
> + if (is_rst_ctrl) {
This can just be "if (cevapriv->rst)"
> + /* Assert the controller reset */
> + reset_control_assert(cevapriv->rst);
> +
> + for (i = 0; i < hpriv->nports; i++) {
> + rc = phy_init(hpriv->phys[i]);
> + if (rc)
> + return rc;
> + }
> +
> + /* De-assert the controller reset */
> + reset_control_deassert(cevapriv->rst);
> +
> + for (i = 0; i < hpriv->nports; i++) {
> + rc = phy_power_on(hpriv->phys[i]);
> + if (rc) {
> + phy_exit(hpriv->phys[i]);
> + return rc;
> + }
> + }
> + }
> +
> if (of_property_read_bool(np, "ceva,broken-gen2"))
> cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
>
regards
Philipp