[PATCH v2 2/2] arm64: dts: ti: k3-j7200-som-p0: Add HyperFlash node

[Vignesh Raghavendra]

J7200 SoM has a HyperFlash connected to HyperBus memory controller. But
HyperBus is muxed with OSPI, therefore keep HyperBus node disabled.
Bootloader will detect the mux and enable the node as required.

Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
---
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 36 +++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index f7e271c442a0..6a98ba499bc2 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -27,3 +27,39 @@ secure_ddr: optee@9e800000 {
 		};
 	};
 };
+
+&wkup_pmx0 {
+	mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (B6) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */
+			J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C8) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */
+			J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (D6) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */
+			J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (D7) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */
+			J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (B7) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */
+			J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D8) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */
+			J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (C7) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */
+			J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (C5) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */
+			J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (A5) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (A6) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */
+			J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (B8) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
+			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
+			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
+		>;
+	};
+};
+
+&hbmc {
+	/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
+	 * appropriate node based on board detection
+	 */
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
+	ranges = <0x00 0x00 0x05 0x00000000 0x4000000>, /* 64MB Flash on CS0 */
+		 <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */
+
+	flash@0,0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x00 0x00 0x4000000>;
+	};
+};
-- 
2.28.0