Re: [PATCH v9 10/20] gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL

[Kent Gibson]

On Wed, Sep 23, 2020 at 07:15:46PM +0300, Andy Shevchenko wrote:
> On Wed, Sep 23, 2020 at 7:14 PM Andy Shevchenko
> <andy.shevchenko@xxxxxxxxx> wrote:
> >
> > On Tue, Sep 22, 2020 at 5:35 AM Kent Gibson <warthog618@xxxxxxxxx> wrote:
> > >
> > > Add support for GPIO_V2_LINE_SET_CONFIG_IOCTL, the uAPI v2
> > > line set config ioctl.
> 
> > > +static long linereq_set_config_unlocked(struct linereq *lr,
> > > +                                       struct gpio_v2_line_config *lc)
> > > +{
> > > +       struct gpio_desc *desc;
> > > +       unsigned int i;
> > > +       u64 flags;
> > > +       bool polarity_change;
> > > +       int ret;
> > > +
> > > +       for (i = 0; i < lr->num_lines; i++) {
> > > +               desc = lr->lines[i].desc;
> > > +               flags = gpio_v2_line_config_flags(lc, i);
> >
> > > +               polarity_change =
> > > +                       (test_bit(FLAG_ACTIVE_LOW, &desc->flags) !=
> > > +                        ((flags & GPIO_V2_LINE_FLAG_ACTIVE_LOW) != 0));
> >
> > Comparison
> 
> Comparison between int / long (not all archs are agreed on this) and
> boolean is not the best we can do.
> 

There is no bool to int comparision here.

There are two comparisons - the inner int vs int => bool and the
outer bool vs bool.  The "!= 0" is effectively an implicit cast to
bool, as is your new_polarity initialisation below.

> What about
> 
>   bool old_polarity = test_bit(FLAG_ACTIVE_LOW, &desc->flags);
>   bool new_polarity = flags & GPIO_V2_LINE_FLAG_ACTIVE_LOW;
> 
>   old_polarity ^ new_polarity
> 

So using bitwise operators on bools is ok??

> and move this under INPUT conditional?
> 

It has to be before the gpio_v2_line_config_flags_to_desc_flags() call,
as that modifies the desc flags, including the new polarity, so
polarity_change would then always be false :-).

Cheers,
Kent.

> > > +
> > > +               gpio_v2_line_config_flags_to_desc_flags(flags, &desc->flags);
> > > +               /*
> > > +                * Lines have to be requested explicitly for input
> > > +                * or output, else the line will be treated "as is".
> > > +                */
> > > +               if (flags & GPIO_V2_LINE_FLAG_OUTPUT) {
> > > +                       int val = gpio_v2_line_config_output_value(lc, i);
> > > +
> > > +                       edge_detector_stop(&lr->lines[i]);
> > > +                       ret = gpiod_direction_output(desc, val);
> > > +                       if (ret)
> > > +                               return ret;
> > > +               } else if (flags & GPIO_V2_LINE_FLAG_INPUT) {
> > > +                       ret = gpiod_direction_input(desc);
> > > +                       if (ret)
> > > +                               return ret;
> > > +
> > > +                       ret = edge_detector_update(&lr->lines[i],
> > > +                                       flags & GPIO_V2_LINE_EDGE_FLAGS,
> > > +                                       polarity_change);
> > > +                       if (ret)
> > > +                               return ret;
> > > +               }
> > > +
> > > +               blocking_notifier_call_chain(&desc->gdev->notifier,
> > > +                                            GPIO_V2_LINE_CHANGED_CONFIG,
> > > +                                            desc);
> > > +       }
> > > +       return 0;
> > > +}
> 
> -- 
> With Best Regards,
> Andy Shevchenko