[PATCH 2/2] mmc: sdhci-acpi: AMDI0040: Allow changing HS200/HS400 driver strength

[Raul E Rangel]

This change will allow platform designers better control over signal
integrity by allowing them to tune the HS200 and HS400 driver strengths.

The driver strength was previously hard coded to A to solve boot
problems with certain platforms. This driver strength does not
universally apply to all platforms so we need a knob to adjust it.

All older platforms currently have the SDR104 preset hard coded to A in
the firmware. This means that switching from the hard coded value in
the kernel to reading the SDR104 preset is a no-op for these platforms.
Newer platforms will have properly set presets. So this change will
support both new and old platforms.

Signed-off-by: Raul E Rangel <rrangel@xxxxxxxxxxxx>
---

 drivers/mmc/host/sdhci-acpi.c | 39 ++++++++++++++++++++++++++++++++---
 1 file changed, 36 insertions(+), 3 deletions(-)

diff --git a/drivers/mmc/host/sdhci-acpi.c b/drivers/mmc/host/sdhci-acpi.c
index d335a34ad05b3..5c9a041af5b4b 100644
--- a/drivers/mmc/host/sdhci-acpi.c
+++ b/drivers/mmc/host/sdhci-acpi.c
@@ -545,10 +545,43 @@ struct amd_sdhci_host {
 
 static int amd_select_drive_strength(struct mmc_card *card,
 				     unsigned int max_dtr, int host_drv,
-				     int card_drv, int *drv_type)
+				     int card_drv, int *host_driver_strength)
 {
-	*drv_type = MMC_SET_DRIVER_TYPE_A;
-	return MMC_SET_DRIVER_TYPE_A;
+	struct sdhci_host *host = mmc_priv(card->host);
+	u16 preset, preset_driver_strength;
+
+	/*
+	 * This method is only called by mmc_select_hs200 so we only need to
+	 * read from the HS200 (SDR104) preset register.
+	 *
+	 * Firmware that has "invalid/default" presets return a driver strength
+	 * of A. This matches the previously hard coded value.
+	 */
+	preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
+	preset_driver_strength =
+		(preset & SDHCI_PRESET_DRV_MASK) >> SDHCI_PRESET_DRV_SHIFT;
+
+	/*
+	 * We want the controller driver strength to match the card's driver
+	 * strength so they have similar rise/fall times.
+	 *
+	 * The controller driver strength set by this method is sticky for all
+	 * timings after this method is called. This unfortunately means that
+	 * while HS400 tuning is in progress we end up with mismatched driver
+	 * strengths between the controller and the card. HS400 tuning requires
+	 * switching from HS400->DDR52->HS->HS200->HS400. So the driver mismatch
+	 * happens while in DDR52 and HS modes. This has not been observed to
+	 * cause problems. Enabling presets would fix this issue.
+	 */
+	*host_driver_strength = preset_driver_strength;
+
+	/*
+	 * The resulting card driver strength is only set when switching the
+	 * card's timing to HS200 or HS400. The card will use the default driver
+	 * strength (B) for any other mode.
+	 */
+	return preset_driver_strength;
+
 }
 
 static void sdhci_acpi_amd_hs400_dll(struct sdhci_host *host, bool enable)
-- 
2.28.0.709.gb0816b6eb0-goog