Re: [PATCH v6 4/4] bus: mhi: Add userspace client interface driver

[Hemant Kumar]

Hi Loic,

On 9/22/20 4:10 AM, Loic Poulain wrote:
> Hi Hemant,
>
> See comments inline, but globally, the locking and ref counting is
> more complicated than it should be.
>
> On Wed, 16 Sep 2020 at 21:57, Hemant Kumar <hemantk@xxxxxxxxxxxxxx> wrote:
> > This MHI client driver allows userspace clients to transfer
> > raw data between MHI device and host using standard file operations.
> > Device file node is created with format
> >
> > /dev/mhi_<controller_name>_<mhi_device_name>
> >
> > Currently it supports LOOPBACK channel.
> >
> > Signed-off-by: Hemant Kumar <hemantk@xxxxxxxxxxxxxx>
> > ---
> >   drivers/bus/mhi/Kconfig  |  13 +
> >   drivers/bus/mhi/Makefile |   4 +
> >   drivers/bus/mhi/uci.c    | 657 +++++++++++++++++++++++++++++++++++++++++++++++
> >   3 files changed, 674 insertions(+)
> >   create mode 100644 drivers/bus/mhi/uci.c
> >
> > diff --git a/drivers/bus/mhi/Kconfig b/drivers/bus/mhi/Kconfig
> > index 6a217ff..8aebe8b 100644
> > --- a/drivers/bus/mhi/Kconfig
> > +++ b/drivers/bus/mhi/Kconfig
> > @@ -20,3 +20,16 @@ config MHI_BUS_DEBUG
> >           Enable debugfs support for use with the MHI transport. Allows
> >           reading and/or modifying some values within the MHI controller
> >           for debug and test purposes.
> > +
> > +config MHI_UCI
> > +       tristate "MHI UCI"
> > +       depends on MHI_BUS
> > +       help
> > +        MHI based userspace client interface driver is used for transferring
> > +        raw data between host and device using standard file operations from
> > +        userspace. Open, read, write, and close operations are supported
> > +        by this driver. Please check mhi_uci_match_table for all supported
> > +        channels that are exposed to userspace.
> > +
> > +        To compile this driver as a module, choose M here: the module will be
> > +        called mhi_uci.
> > diff --git a/drivers/bus/mhi/Makefile b/drivers/bus/mhi/Makefile
> > index 19e6443..80feefb 100644
> > --- a/drivers/bus/mhi/Makefile
> > +++ b/drivers/bus/mhi/Makefile
> > @@ -1,2 +1,6 @@
> >   # core layer
> >   obj-y += core/
> > +
> > +# MHI client
> > +mhi_uci-y := uci.o
> > +obj-$(CONFIG_MHI_UCI) += mhi_uci.o
> > diff --git a/drivers/bus/mhi/uci.c b/drivers/bus/mhi/uci.c
> > new file mode 100644
> > index 0000000..d6758f2
> > --- /dev/null
> > +++ b/drivers/bus/mhi/uci.c
> > @@ -0,0 +1,657 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/* Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.*/
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/mhi.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/module.h>
> > +#include <linux/poll.h>
> > +
> > +#define DEVICE_NAME "mhi"
> > +#define MHI_UCI_DRIVER_NAME "mhi_uci"
> > +#define MAX_UCI_MINORS (128)
> > +
> > +static DEFINE_IDR(uci_idr);
> > +static DEFINE_MUTEX(uci_idr_mutex);
> > +static struct class *uci_dev_class;
> > +static int uci_dev_major;
> > +
> > +/**
> > + * struct uci_chan - MHI channel for a uci device
> > + * @wq: wait queue for reader/writer
> > + * @lock: spin lock
> > + * @pending: list of rx buffers userspace is waiting to read
> > + * @cur_buf: current buffer userspace is reading
> > + * @rx_size: size of the current rx buffer userspace is reading
> > + */
> > +struct uci_chan {
> > +       wait_queue_head_t wq;
> > +
> > +       /* protects pending and cur_buf members in bh context */
> > +       spinlock_t lock;
> > +
> > +       struct list_head pending;
> > +       struct uci_buf *cur_buf;
> > +       size_t rx_size;
> > +};
> > +
> > +/**
> > + * struct uci_buf - uci buffer
> > + * @data: data buffer
> > + * @len: length of data buffer
> > + * @node: list node of the uci buffer
> > + */
> > +struct uci_buf {
> > +       void *data;
> > +       size_t len;
> > +       struct list_head node;
> > +};
> > +
> > +/**
> > + * struct uci_dev - MHI uci device
> > + * @minor: uci device node minor number
> > + * @mhi_dev: associated mhi device object
> > + * @chan: MHI channel name
> > + * @lock: mutex lock
> > + * @ul_chan: uplink uci channel object
> > + * @dl_chan: downlink uci channel object
> > + * @mtu: max tx buffer length
> > + * @actual_mtu: maximum size of incoming buffer
> > + * @open: open called for device node
> > + * @enabled: uci device probed
> > + * @ref_count: uci_dev reference count
> > + */
> > +struct uci_dev {
> > +       unsigned int minor;
> > +       struct mhi_device *mhi_dev;
> > +       const char *chan;
> > +
> > +       /* protects uci_dev struct members */
> > +       struct mutex lock;
> > +
> > +       struct uci_chan ul_chan;
> > +       struct uci_chan dl_chan;
> > +       size_t mtu;
> > +       size_t actual_mtu;
> > +       bool enabled;
> > +       struct kref ref_count;
> > +};
> > +
> > +static int mhi_queue_inbound(struct uci_dev *udev)
> > +{
> > +       struct mhi_device *mhi_dev = udev->mhi_dev;
> > +       struct device *dev = &mhi_dev->dev;
> > +       size_t mtu = udev->mtu;
> > +       size_t actual_mtu = udev->actual_mtu;
> > +       int nr_trbs, i, ret = -EIO;
> > +       void *buf;
> > +       struct uci_buf *uci_buf;
> > +
> > +       nr_trbs = mhi_get_no_free_descriptors(mhi_dev, DMA_FROM_DEVICE);
> > +
> > +       for (i = 0; i < nr_trbs; i++) {
> > +               buf = kmalloc(mtu, GFP_KERNEL);
> > +               if (!buf)
> > +                       return -ENOMEM;
> > +
> > +               uci_buf = buf + actual_mtu;
> > +               uci_buf->data = buf;
> > +
> > +               dev_dbg(dev, "Allocated buf %d of %d size %ld\n", i, nr_trbs,
> > +                       actual_mtu);
> > +
> > +               ret = mhi_queue_buf(mhi_dev, DMA_FROM_DEVICE, buf, actual_mtu,
> > +                                   MHI_EOT);
> > +               if (ret) {
> > +                       kfree(buf);
> > +                       dev_err(dev, "Failed to queue buffer %d\n", i);
> > +                       return ret;
> > +               }
> > +       }
> > +
> > +       return ret;
> > +}
> > +
> > +static void mhi_uci_dev_release(struct kref *ref)
> > +{
> > +       struct uci_dev *udev =
> > +               container_of(ref, struct uci_dev, ref_count);
> > +
> > +       mutex_destroy(&udev->lock);
> > +
> > +       dev_set_drvdata(&udev->mhi_dev->dev, NULL);
> > +
> > +       kfree(udev);
> > +}
> > +
> > +static int mhi_uci_release(struct inode *inode, struct file *file)
> > +{
> > +       struct uci_dev *udev = file->private_data;
> > +       struct uci_buf *itr, *tmp;
> > +       struct uci_chan *uchan;
> > +
> > +       if (kref_read(&udev->ref_count) > 2)
> > +               goto exit_uci_release;
> > +
> > +       if (udev->enabled)
> > +               mhi_unprepare_from_transfer(udev->mhi_dev);
> > +
> > +       /* clean inbound channel */
> > +       uchan = &udev->dl_chan;
> > +
> > +       spin_lock_bh(&uchan->lock);
> > +       list_for_each_entry_safe(itr, tmp, &uchan->pending, node) {
> > +               list_del(&itr->node);
> > +               kfree(itr->data);
> > +       }
> > +
> > +       if (uchan->cur_buf)
> > +               kfree(uchan->cur_buf->data);
> > +
> > +       uchan->cur_buf = NULL;
> > +       spin_unlock_bh(&uchan->lock);
> > +
> > +exit_uci_release:
> > +       kref_put(&udev->ref_count, mhi_uci_dev_release);
> > +
> > +       return 0;
> > +}
> > +
> > +static __poll_t mhi_uci_poll(struct file *file, poll_table *wait)
> > +{
> > +       struct uci_dev *udev = file->private_data;
> > +       struct mhi_device *mhi_dev = udev->mhi_dev;
> > +       struct device *dev = &mhi_dev->dev;
> > +       struct uci_chan *uchan;
> > +       __poll_t mask = 0;
> > +
> > +       poll_wait(file, &udev->dl_chan.wq, wait);
> > +       poll_wait(file, &udev->ul_chan.wq, wait);
> > +
> > +       if (!udev->enabled) {
> > +               mask = EPOLLERR;
> > +       } else {
> > +               uchan = &udev->dl_chan;
> > +               spin_lock_bh(&uchan->lock);
> > +               if (!list_empty(&uchan->pending) || uchan->cur_buf) {
> > +                       dev_dbg(dev, "Client can read from node\n");
> > +                       mask |= EPOLLIN | EPOLLRDNORM;
> > +               }
> > +               spin_unlock_bh(&uchan->lock);
> > +       }
> > +
> > +       if (!udev->enabled) {
> > +               mask |= EPOLLERR;
> > +       } else if (mhi_get_no_free_descriptors(mhi_dev, DMA_TO_DEVICE) > 0) {
> > +               dev_dbg(dev, "Client can write to node\n");
> > +               mask |= EPOLLOUT | EPOLLWRNORM;
> > +       }
> > +
> > +       dev_dbg(dev, "Client attempted to poll, returning mask 0x%x\n", mask);
> > +
> > +       return mask;
> > +}
> > +
> > +static ssize_t mhi_uci_write(struct file *file,
> > +                            const char __user *buf,
> > +                            size_t count,
> > +                            loff_t *offp)
> > +{
> > +       struct uci_dev *udev = file->private_data;
> > +       struct mhi_device *mhi_dev = udev->mhi_dev;
> > +       struct device *dev = &mhi_dev->dev;
> > +       struct uci_chan *uchan = &udev->ul_chan;
> > +       size_t bytes_xfered = 0;
> > +       int ret, nr_avail = 0;
> > +
> > +       if (!buf || !count)
> > +               return -EINVAL;
> > +
> > +       /* confirm channel is active */
> > +       mutex_lock(&udev->lock);
> > +       if (!udev->enabled) {
> > +               ret = -ENODEV;
> > +               goto err_mtx_unlock;
> > +       }
> > +
> > +       dev_dbg(dev, "%s: to xfer: %lu bytes\n", __func__, count);
> > +
> > +       while (count) {
> > +               size_t xfer_size;
> > +               void *kbuf;
> > +               enum mhi_flags flags;
> > +
> > +               mutex_unlock(&udev->lock);
> > +               /* wait for free descriptors */
> > +               ret = wait_event_interruptible(uchan->wq,
> > +                                              (!udev->enabled) ||
> > +                               (nr_avail = mhi_get_no_free_descriptors(mhi_dev,
> > +                                              DMA_TO_DEVICE)) > 0);
> > +
> > +               mutex_lock(&udev->lock);
>
> All this locking unlocking is odd:
> - why do you need locking for testing wait_event return code?
> - why do you need this udev->enabled?
udev->enabled used in wait_event_interruptible to unblock in remove. I 
am going to get rid of udev->enabled check that is added on top of this 
function and also before calling mhi_queue_buf below.
> - The MHI core should be thread safe + mhi_queue_buf should simply
> fail if removing is ongoing.
>
> > +               if (ret == -ERESTARTSYS) {
> > +                       dev_dbg(dev, "Exit signal caught for node\n");
> > +                       goto err_mtx_unlock;
> > +               }
> > +
> > +               if (!udev->enabled) {
> > +                       ret = -ENODEV;
> > +                       goto err_mtx_unlock;
> > +               }
> > +
> > +               xfer_size = min_t(size_t, count, udev->mtu);
> > +               kbuf = kmalloc(xfer_size, GFP_KERNEL);
> > +               if (!kbuf) {
> > +                       ret = -ENOMEM;
> > +                       goto err_mtx_unlock;
> > +               }
> > +
> > +               ret = copy_from_user(kbuf, buf, xfer_size);
> > +               if (ret) {
> > +                       kfree(kbuf);
> > +                       ret = -EFAULT;
> > +                       goto err_mtx_unlock;
> > +               }
> > +
> > +               /* if ring is full after this force EOT */
> > +               if (nr_avail > 1 && (count - xfer_size))
> > +                       flags = MHI_CHAIN;
> > +               else
> > +                       flags = MHI_EOT;
> > +
> > +               if (udev->enabled)
> > +                       ret = mhi_queue_buf(mhi_dev, DMA_TO_DEVICE, kbuf,
> > +                                           xfer_size, flags);
> > +               else
> > +                       ret = -ENODEV;
> > +
> > +               if (ret) {
> > +                       kfree(kbuf);
> > +                       goto err_mtx_unlock;
> > +               }
> > +
> > +               bytes_xfered += xfer_size;
> > +               count -= xfer_size;
> > +               buf += xfer_size;
> > +       }
> > +
> > +       mutex_unlock(&udev->lock);
> > +       dev_dbg(dev, "%s: bytes xferred: %lu\n", __func__, bytes_xfered);
> > +
> > +       return bytes_xfered;
> > +
> > +err_mtx_unlock:
> > +       mutex_unlock(&udev->lock);
> > +
> > +       return ret;
> > +}
> > +
> > +static ssize_t mhi_uci_read(struct file *file,
> > +                           char __user *buf,
> > +                           size_t count,
> > +                           loff_t *ppos)
> > +{
> > +       struct uci_dev *udev = file->private_data;
> > +       struct mhi_device *mhi_dev = udev->mhi_dev;
> > +       struct uci_chan *uchan = &udev->dl_chan;
> > +       struct device *dev = &mhi_dev->dev;
> > +       struct uci_buf *ubuf;
> > +       char *ptr;
> > +       size_t to_copy;
> > +       int ret = 0;
> > +
> > +       if (!buf)
> > +               return -EINVAL;
> > +
> > +       mutex_lock(&udev->lock);
> > +       /* confirm channel is active */
> > +       if (!udev->enabled) {
> > +               ret = -ENODEV;
> > +               goto err_mtx_unlock;
> > +       }
> > +
> > +       spin_lock_bh(&uchan->lock);
> > +       /* No data available to read, wait */
> > +       if (!uchan->cur_buf && list_empty(&uchan->pending)) {
> > +               dev_dbg(dev, "No data available to read waiting\n");
> > +
> > +               spin_unlock_bh(&uchan->lock);
> > +               mutex_unlock(&udev->lock);
> > +               ret = wait_event_interruptible(uchan->wq,
> > +                                              (!udev->enabled ||
> > +                                             !list_empty(&uchan->pending)));
> > +
> > +               mutex_lock(&udev->lock);
> > +               if (ret == -ERESTARTSYS) {
> > +                       dev_dbg(dev, "Exit signal caught for node\n");
> > +                       goto err_mtx_unlock;
> > +               }
> > +
> > +               if (!udev->enabled) {
> > +                       ret = -ENODEV;
> > +                       goto err_mtx_unlock;
> > +               }
> > +               spin_lock_bh(&uchan->lock);
> > +       }
> > +
> > +       /* new read, get the next descriptor from the list */
> > +       if (!uchan->cur_buf) {
> > +               ubuf = list_first_entry_or_null(&uchan->pending,
> > +                                               struct uci_buf, node);
> > +               if (!ubuf) {
> > +                       ret = -EIO;
> > +                       goto err_spin_unlock;
> > +               }
> > +
> > +               list_del(&ubuf->node);
> > +               uchan->cur_buf = ubuf;
> > +               uchan->rx_size = ubuf->len;
> > +               dev_dbg(dev, "Got pkt of size: %zu\n", uchan->rx_size);
> > +       }
> > +
> > +       ubuf = uchan->cur_buf;
> > +
> > +       /* Copy the buffer to user space */
> > +       to_copy = min_t(size_t, count, uchan->rx_size);
> > +       ptr = ubuf->data + (ubuf->len - uchan->rx_size);
> > +       spin_unlock_bh(&uchan->lock);
> > +
> > +       ret = copy_to_user(buf, ptr, to_copy);
> > +       if (ret) {
> > +               ret = -EFAULT;
> > +               goto err_mtx_unlock;
> > +       }
> > +
> > +       spin_lock_bh(&uchan->lock);
> > +
> > +       dev_dbg(dev, "Copied %lu of %lu bytes\n", to_copy, uchan->rx_size);
> > +       uchan->rx_size -= to_copy;
> > +
> > +       /* we finished with this buffer, queue it back to hardware */
> > +       if (!uchan->rx_size) {
> > +               uchan->cur_buf = NULL;
> > +
> > +               if (udev->enabled)
> > +                       ret = mhi_queue_buf(mhi_dev, DMA_FROM_DEVICE,
> > +                                           ubuf->data,
> > +                                           udev->actual_mtu, MHI_EOT);
> > +               else
> > +                       ret = -ENODEV;
> > +
> > +               if (ret) {
> > +                       dev_err(dev, "Failed to recycle element: %d\n", ret);
> > +                       kfree(ubuf->data);
> > +                       goto err_spin_unlock;
> > +               }
> > +       }
> > +       spin_unlock_bh(&uchan->lock);
> > +       mutex_unlock(&udev->lock);
> > +
> > +       dev_dbg(dev, "%s: Returning %lu bytes\n", __func__, to_copy);
> > +
> > +       return to_copy;
> > +
> > +err_spin_unlock:
> > +       spin_unlock_bh(&uchan->lock);
> > +err_mtx_unlock:
> > +       mutex_unlock(&udev->lock);
> > +       return ret;
> > +}
> > +
> > +static int mhi_uci_open(struct inode *inode, struct file *filp)
> > +{
> > +       struct uci_dev *udev = NULL;
> > +       unsigned int minor = iminor(inode);
> > +       int ret = -EIO;
> > +       struct uci_buf *buf_itr, *tmp;
> > +       struct uci_chan *dl_chan;
> > +       struct mhi_device *mhi_dev;
> > +       struct device *dev;
> > +
> > +       mutex_lock(&uci_idr_mutex);
> > +       udev = idr_find(&uci_idr, minor);
> > +       mutex_unlock(&uci_idr_mutex);
> > +       if (!udev) {
> > +               pr_err("uci dev: minor %d not found\n", minor);
> > +               ret = -ENODEV;
> > +               goto error_no_dev;
> > +       }
> > +
> > +       kref_get(&udev->ref_count);
> > +
> > +       mhi_dev = udev->mhi_dev;
> > +       dev = &mhi_dev->dev;
> > +
> > +       mutex_lock(&udev->lock);
> > +       if (kref_read(&udev->ref_count) > 2) {
> > +               dev_dbg(dev, "Node already opened\n");
> > +               goto exit_uci_open;
> > +       }
> > +
> > +       if (!udev->enabled) {
> > +               dev_info(dev, "Node exists, but is not in active state!\n");
> > +               goto error_open_chan;
> > +       }
> > +
> > +       dev_dbg(dev, "Starting channel\n");
> > +       ret = mhi_prepare_for_transfer(udev->mhi_dev);
> > +       if (ret) {
> > +               dev_err(dev, "Error starting transfer channels\n");
> > +               goto error_open_chan;
> > +       }
> > +
> > +       ret = mhi_queue_inbound(udev);
> > +       if (ret)
> > +               goto error_rx_queue;
> > +
> > +exit_uci_open:
> > +       filp->private_data = udev;
> > +       mutex_unlock(&udev->lock);
> > +
> > +       return 0;
> > +
> > +error_rx_queue:
> > +       dl_chan = &udev->dl_chan;
> > +       mhi_unprepare_from_transfer(udev->mhi_dev);
> > +       list_for_each_entry_safe(buf_itr, tmp, &dl_chan->pending, node) {
> > +               list_del(&buf_itr->node);
> > +               kfree(buf_itr->data);
> > +       }
> > +error_open_chan:
> > +       mutex_unlock(&udev->lock);
> > +       kref_put(&udev->ref_count, mhi_uci_dev_release);
> > +error_no_dev:
> > +       return ret;
> > +}
> > +
> > +static const struct file_operations mhidev_fops = {
> > +       .owner = THIS_MODULE,
> > +       .open = mhi_uci_open,
> > +       .release = mhi_uci_release,
> > +       .read = mhi_uci_read,
> > +       .write = mhi_uci_write,
> > +       .poll = mhi_uci_poll,
> > +};
> > +
> > +static void mhi_ul_xfer_cb(struct mhi_device *mhi_dev,
> > +                          struct mhi_result *mhi_result)
> > +{
> > +       struct uci_dev *udev = dev_get_drvdata(&mhi_dev->dev);
> > +       struct uci_chan *uchan = &udev->ul_chan;
> > +       struct device *dev = &mhi_dev->dev;
> > +
> > +       dev_dbg(dev, "status: %d xfer_len: %zu\n",
> > +               mhi_result->transaction_status, mhi_result->bytes_xferd);
> > +
> > +       kfree(mhi_result->buf_addr);
> > +
> > +       if (!mhi_result->transaction_status)
> > +               wake_up(&uchan->wq);
> > +}
> > +
> > +static void mhi_dl_xfer_cb(struct mhi_device *mhi_dev,
> > +                          struct mhi_result *mhi_result)
> > +{
> > +       struct uci_dev *udev = dev_get_drvdata(&mhi_dev->dev);
> > +       struct uci_chan *uchan = &udev->dl_chan;
> > +       struct device *dev = &mhi_dev->dev;
> > +       struct uci_buf *buf;
> > +
> > +       dev_dbg(dev, "status: %d receive_len: %zu\n",
> > +               mhi_result->transaction_status, mhi_result->bytes_xferd);
> > +
> > +       if (mhi_result->transaction_status == -ENOTCONN) {
> > +               kfree(mhi_result->buf_addr);
> > +               return;
> > +       }
> > +
> > +       spin_lock_bh(&uchan->lock);
> > +       buf = mhi_result->buf_addr + udev->actual_mtu;
> > +       buf->data = mhi_result->buf_addr;
> > +       buf->len = mhi_result->bytes_xferd;
>
> You don't need to protect buf here, only uchan pending list, right? so
> move lock here.
Done.
> > +       list_add_tail(&buf->node, &uchan->pending);
> > +       spin_unlock_bh(&uchan->lock);
> > +
> > +       wake_up(&uchan->wq);
> > +}
> > +
> > +static int mhi_uci_probe(struct mhi_device *mhi_dev,
> > +                        const struct mhi_device_id *id)
> > +{
> > +       struct uci_dev *udev;
> > +       struct mhi_controller *mhi_cntrl = mhi_dev->mhi_cntrl;
> > +       struct device *dev;
> > +       int index, dir;
> > +
> > +       udev = kzalloc(sizeof(*udev), GFP_KERNEL);
> > +       if (!udev)
> > +               return -ENOMEM;
> > +
> > +       kref_init(&udev->ref_count);
> > +       mutex_init(&udev->lock);
> > +       udev->mhi_dev = mhi_dev;
> > +
> > +       mutex_lock(&udev->lock);
>
> Why locking here? udev has just been created, it cannot be used concurrently.
Done, will remove it.
> > +
> > +       mutex_lock(&uci_idr_mutex);
> > +       index = idr_alloc(&uci_idr, udev, 0, MAX_UCI_MINORS, GFP_KERNEL);
> > +       mutex_unlock(&uci_idr_mutex);
> > +       if (index < 0) {
> > +               mutex_unlock(&udev->lock);
> > +               kfree(udev);
> > +               return index;
> > +       }
> > +
> > +       udev->minor = index;
> > +
> > +       /* create device file node /dev/mhi_<cntrl_dev_name>_<mhi_dev_name> */
> > +       dev = device_create(uci_dev_class, &mhi_dev->dev,
> > +                           MKDEV(uci_dev_major, index), udev,
> > +                           DEVICE_NAME "_%s_%s",
> > +                           dev_name(mhi_cntrl->cntrl_dev), mhi_dev->name);
> > +       if (IS_ERR(dev)) {
> > +               mutex_lock(&uci_idr_mutex);
> > +               idr_remove(&uci_idr, udev->minor);
> > +               mutex_unlock(&uci_idr_mutex);
> > +               mutex_unlock(&udev->lock);
> > +               kfree(udev);
> > +               return PTR_ERR(dev);
> > +       }
>
> I would suggest adding the device at the very end of the probe, when
> everything has been initialized.
Done, will do that.
> Regards,
> Loic
>
>
>
> > +
> > +       for (dir = 0; dir < 2; dir++) {
> > +               struct uci_chan *uchan = (dir) ?
> > +                       &udev->ul_chan : &udev->dl_chan;
> > +               spin_lock_init(&uchan->lock);
> > +               init_waitqueue_head(&uchan->wq);
> > +               INIT_LIST_HEAD(&uchan->pending);
> > +       }
> > +
> > +       udev->mtu = min_t(size_t, id->driver_data, MHI_MAX_MTU);
> > +       udev->actual_mtu = udev->mtu - sizeof(struct uci_buf);
> > +       dev_set_drvdata(&mhi_dev->dev, udev);
> > +       udev->enabled = true;
> > +
> > +       mutex_unlock(&udev->lock);
> > +
> > +       dev_info(&mhi_dev->dev, "probed uci dev: minor %d\n", index);
> > +
> > +       return 0;
> > +};
> > +
> > +static void mhi_uci_remove(struct mhi_device *mhi_dev)
> > +{
> > +       struct uci_dev *udev = dev_get_drvdata(&mhi_dev->dev);
> > +
> > +       mutex_lock(&udev->lock);
> > +
> > +       /* disable the node */
> > +       udev->enabled = false;
> > +
> > +       wake_up(&udev->dl_chan.wq);
> > +       wake_up(&udev->ul_chan.wq);
> > +
> > +       /* delete the node to prevent new opens */
> > +       device_destroy(uci_dev_class, MKDEV(uci_dev_major, udev->minor));
> > +
> > +       mutex_lock(&uci_idr_mutex);
> > +       idr_remove(&uci_idr, udev->minor);
> > +       mutex_unlock(&uci_idr_mutex);
> > +
> > +       mutex_unlock(&udev->lock);
> > +
> > +       kref_put(&udev->ref_count, mhi_uci_dev_release);
> > +}
> > +
> > +/* .driver_data stores max mtu */
> > +static const struct mhi_device_id mhi_uci_match_table[] = {
> > +       { .chan = "LOOPBACK", .driver_data = 0x1000},
> > +       {},
> > +};
> > +MODULE_DEVICE_TABLE(mhi, mhi_uci_match_table);
> > +
> > +static struct mhi_driver mhi_uci_driver = {
> > +       .id_table = mhi_uci_match_table,
> > +       .remove = mhi_uci_remove,
> > +       .probe = mhi_uci_probe,
> > +       .ul_xfer_cb = mhi_ul_xfer_cb,
> > +       .dl_xfer_cb = mhi_dl_xfer_cb,
> > +       .driver = {
> > +               .name = MHI_UCI_DRIVER_NAME,
> > +       },
> > +};
> > +
> > +static int mhi_uci_init(void)
> > +{
> > +       int ret;
> > +
> > +       ret = register_chrdev(0, MHI_UCI_DRIVER_NAME, &mhidev_fops);
> > +       if (ret < 0)
> > +               return ret;
> > +
> > +       uci_dev_major = ret;
> > +       uci_dev_class = class_create(THIS_MODULE, MHI_UCI_DRIVER_NAME);
> > +       if (IS_ERR(uci_dev_class)) {
> > +               unregister_chrdev(uci_dev_major, MHI_UCI_DRIVER_NAME);
> > +               return -ENODEV;
> > +       }
> > +
> > +       ret = mhi_driver_register(&mhi_uci_driver);
> > +       if (ret) {
> > +               class_destroy(uci_dev_class);
> > +               unregister_chrdev(uci_dev_major, MHI_UCI_DRIVER_NAME);
> > +       }
> > +
> > +       return ret;
> > +}
> > +
> > +static void __exit mhi_uci_exit(void)
> > +{
> > +       mhi_driver_unregister(&mhi_uci_driver);
> > +       class_destroy(uci_dev_class);
> > +       unregister_chrdev(uci_dev_major, MHI_UCI_DRIVER_NAME);
> > +}
> > +
> > +module_init(mhi_uci_init);
> > +module_exit(mhi_uci_exit);
> > +MODULE_LICENSE("GPL v2");
> > +MODULE_DESCRIPTION("MHI UCI Driver");
> > --
> > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> > a Linux Foundation Collaborative Project
Thanks for reviewing my change Loic, based on concerns from Greg and 
Jeff, i am working on pushing another patch set. This patch set also 
address locking related concern that you mentioned. Basically intent for 
adding udev ref count is to take care of race between driver remove() 
and file open(). So i am keeping udev ref count in the next patch set 
but in order to take care of corner cases i need to guard udev ref 
counting with global mutex. udev needs to ref count the channel so that 
mhi channel is started when first open is called and channel is stopped 
only when the last release is called. So we need some kind of ref 
counting for channel usage as well. Will remove the current way of doing 
channel ref counting using udev ref count value.

Thanks,
Hemant
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project