Re: [PATCH v3 2/2] Add hardware monitoring driver for Moortec MR75203 PVT controller

[Tanwar, Rahul]

Hi Guenter,

On 2/10/2020 2:26 am, Guenter Roeck wrote:
> On 9/29/20 1:59 AM, Rahul Tanwar wrote:
>> PVT controller (MR75203) is used to configure & control
>> Moortec embedded analog IP which contains temprature
>> sensor(TS), voltage monitor(VM) & process detector(PD)
>> modules. Add hardware monitoring driver to support
>> MR75203 PVT controller.
>>
>> Signed-off-by: Rahul Tanwar <rahul.tanwar@xxxxxxxxxxxxxxx>
>> ---
>>  drivers/hwmon/Kconfig   |  10 +
>>  drivers/hwmon/Makefile  |   1 +
>>  drivers/hwmon/mr75203.c | 605 ++++++++++++++++++++++++++++++++++++++++++++++++
>>  3 files changed, 616 insertions(+)
>>  create mode 100644 drivers/hwmon/mr75203.c
>>
>> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
>> index 8dc28b26916e..2defb46677b4 100644
>> --- a/drivers/hwmon/Kconfig
>> +++ b/drivers/hwmon/Kconfig
>> @@ -1112,6 +1112,16 @@ config SENSORS_MENF21BMC_HWMON
>>  	  This driver can also be built as a module. If so the module
>>  	  will be called menf21bmc_hwmon.
>>  
>> +config SENSORS_MR75203
>> +	tristate "Moortec Semiconductor MR75203 PVT Controller"
>> +	select REGMAP_MMIO
>> +	help
>> +	  If you say yes here you get support for Moortec MR75203
>> +	  PVT controller.
>> +
>> +	  This driver can also be built as a module. If so, the module
>> +	  will be called mr75203.
>> +
>>  config SENSORS_ADCXX
>>  	tristate "National Semiconductor ADCxxxSxxx"
>>  	depends on SPI_MASTER
>> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
>> index a8f4b35b136b..bb4bd92a5149 100644
>> --- a/drivers/hwmon/Makefile
>> +++ b/drivers/hwmon/Makefile
>> @@ -142,6 +142,7 @@ obj-$(CONFIG_SENSORS_MCP3021)	+= mcp3021.o
>>  obj-$(CONFIG_SENSORS_TC654)	+= tc654.o
>>  obj-$(CONFIG_SENSORS_MLXREG_FAN) += mlxreg-fan.o
>>  obj-$(CONFIG_SENSORS_MENF21BMC_HWMON) += menf21bmc_hwmon.o
>> +obj-$(CONFIG_SENSORS_MR75203)	+= mr75203.o
>>  obj-$(CONFIG_SENSORS_NCT6683)	+= nct6683.o
>>  obj-$(CONFIG_SENSORS_NCT6775)	+= nct6775.o
>>  obj-$(CONFIG_SENSORS_NCT7802)	+= nct7802.o
>> diff --git a/drivers/hwmon/mr75203.c b/drivers/hwmon/mr75203.c
>> new file mode 100644
>> index 000000000000..30a70a3ae82b
>> --- /dev/null
>> +++ b/drivers/hwmon/mr75203.c
>> @@ -0,0 +1,605 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (C) 2020 MaxLinear, Inc.
>> + *
>> + * This driver is a hardware monitoring driver for PVT controller
>> + * (MR75203) which is used to configure & control Moortec embedded
>> + * analog IP to enable multiple embedded temprature sensor(TS),
>
> temperature

Well noted.

>> + * voltage monitor(VM) & process detector(PD) modules.
>> + */
>> +#include <linux/clk.h>
>> +#include <linux/hwmon.h>
>> +#include <linux/module.h>
>> +#include <linux/mod_devicetable.h>
>> +#include <linux/mutex.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/property.h>
>> +#include <linux/regmap.h>
>> +#include <linux/reset.h>
>> +
>> +/* PVT Common register */
>> +#define PVT_IP_CONFIG	0x04
>> +#define TS_NUM_MSK	GENMASK(4, 0)
>> +#define TS_NUM_SFT	0
>> +#define PD_NUM_MSK	GENMASK(12, 8)
>> +#define PD_NUM_SFT	8
>> +#define VM_NUM_MSK	GENMASK(20, 16)
>> +#define VM_NUM_SFT	16
>> +#define CH_NUM_MSK	GENMASK(31, 24)
>> +#define CH_NUM_SFT	24
>> +
>> +/* Macro Common Register */
>> +#define CLK_SYNTH		0x00
>> +#define CLK_SYNTH_LO_SFT	0
>> +#define CLK_SYNTH_HI_SFT	8
>> +#define CLK_SYNTH_HOLD_SFT	16
>> +#define CLK_SYNTH_EN		BIT(24)
>> +#define CLK_SYS_CYCLES_MAX	514
>> +#define CLK_SYS_CYCLES_MIN	2
>> +#define HZ_PER_MHZ		1000000L
>> +
>> +#define SDIF_DISABLE	0x04
>> +
>> +#define SDIF_STAT	0x08
>> +#define SDIF_BUSY	BIT(0)
>> +#define SDIF_LOCK	BIT(1)
>> +
>> +#define SDIF_W		0x0c
>> +#define SDIF_PROG	BIT(31)
>> +#define SDIF_WRN_W	BIT(27)
>> +#define SDIF_WRN_R	0x00
>> +#define SDIF_ADDR_SFT	24
>> +
>> +#define SDIF_HALT	0x10
>> +#define SDIF_CTRL	0x14
>> +#define SDIF_SMPL_CTRL	0x20
>> +
>> +/* TS & PD Individual Macro Register */
>> +#define COM_REG_SIZE	0x40
>> +
>> +#define SDIF_DONE(n)	(COM_REG_SIZE + 0x14 + 0x40 * (n))
>> +#define SDIF_SMPL_DONE	BIT(0)
>> +
>> +#define SDIF_DATA(n)	(COM_REG_SIZE + 0x18 + 0x40 * (n))
>> +#define SAMPLE_DATA_MSK	GENMASK(15, 0)
>> +
>> +#define HILO_RESET(n)	(COM_REG_SIZE + 0x2c + 0x40 * (n))
>> +
>> +/* VM Individual Macro Register */
>> +#define VM_COM_REG_SIZE	0x200
>> +#define VM_SDIF_DONE(n)	(VM_COM_REG_SIZE + 0x34 + 0x200 * (n))
>> +#define VM_SDIF_DATA(n)	(VM_COM_REG_SIZE + 0x40 + 0x200 * (n))
>> +
>> +/* SDA Slave Register */
>> +#define IP_CTRL			0x00
>> +#define IP_RST_REL		BIT(1)
>> +#define IP_RUN_CONT		BIT(3)
>> +#define IP_AUTO			BIT(8)
>> +#define IP_VM_MODE		BIT(10)
>> +
>> +#define IP_CFG			0x01
>> +#define CFG0_MODE_2		BIT(0)
>> +#define CFG0_PARALLEL_OUT	0
>> +#define CFG0_12_BIT		0
>> +#define CFG1_VOL_MEAS_MODE	0
>> +#define CFG1_PARALLEL_OUT	0
>> +#define CFG1_14_BIT		0
>> +
>> +#define IP_DATA		0x03
>> +
>> +#define IP_POLL		0x04
>> +#define VM_CH_INIT	BIT(20)
>> +#define VM_CH_REQ	BIT(21)
>> +
>> +#define IP_TMR			0x05
>> +#define POWER_DELAY_CYCLE_256	0x80
>> +#define POWER_DELAY_CYCLE_64	0x40
>> +
>> +#define PVT_POLL_DELAY_US	20
>> +#define PVT_POLL_TIMEOUT_US	20000
>> +#define PVT_H_CONST		100000
>> +#define PVT_CAL5_CONST		2047
>> +#define PVT_G_CONST		40000
>> +#define PVT_CONV_BITS		10
>> +#define PVT_N_CONST		90
>> +#define PVT_R_CONST		245805
>> +
>> +struct pvt_device {
>> +	struct regmap		*c_map;
>> +	struct regmap		*t_map;
>> +	struct regmap		*p_map;
>> +	struct regmap		*v_map;
>> +	struct clk		*clk;
>> +	struct reset_control	*rst;
>> +	u32			t_num;
>> +	u32			p_num;
>> +	u32			v_num;
>> +	u32			ip_freq;
>> +	u8			*vm_idx;
>> +};
>> +
>> +static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type,
>> +			      u32 attr, int channel)
>> +{
>> +	switch (type) {
>> +	case hwmon_temp:
>> +		if (attr == hwmon_temp_input)
>> +			return 0444;
>> +		else
>> +			return 0;
>> +	case hwmon_in:
>> +		if (attr == hwmon_in_input)
>> +			return 0444;
>> +		else
>> +			return 0;
> else after return is unnecessary.

Agree, will update.

>> +	default:
>> +		return 0;
>> +	}
>> +}
>> +
>> +static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val)
>> +{
>> +	struct pvt_device *pvt = dev_get_drvdata(dev);
>> +	struct regmap *t_map = pvt->t_map;
>> +	u32 stat, nbs;
>> +	int ret;
>> +	u64 tmp;
>> +
>> +	if (channel >= pvt->t_num)
>> +		return -EINVAL;
>> +
> Those checks are not really needed.

Well noted.

>> +	switch (attr) {
>> +	case hwmon_temp_input:
>> +		ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel),
>> +					       stat, stat & SDIF_SMPL_DONE,
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		regmap_read(t_map, SDIF_DATA(channel), &nbs);
> regmap_read() can return an error.

Yes, agree. Will update all regmap read/writes.

>> +		nbs &= SAMPLE_DATA_MSK;
>> +
>> +		/*
>> +		 * Convert the register value to
>> +		 * degrees centigrade temperature
>> +		 */
>> +		tmp = nbs * PVT_H_CONST;
>> +		do_div(tmp, PVT_CAL5_CONST);
>> +		*val = tmp - PVT_G_CONST - pvt->ip_freq;
>> +
>> +		return 0;
>> +	default:
>> +		return -EOPNOTSUPP;
>> +	}
>> +}
>> +
>> +static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val)
>> +{
>> +	struct pvt_device *pvt = dev_get_drvdata(dev);
>> +	struct regmap *v_map = pvt->v_map;
>> +	u32 n, stat;
>> +	u8 vm_idx;
>> +	int ret;
>> +
>> +	if (channel >= pvt->v_num)
>> +		return -EINVAL;
>> +
>> +	vm_idx = pvt->vm_idx[channel];
>> +
>> +	switch (attr) {
>> +	case hwmon_in_input:
>> +		ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx),
>> +					       stat, stat & SDIF_SMPL_DONE,
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		regmap_read(v_map, VM_SDIF_DATA(vm_idx), &n);
> regmap_read can return an error.
>
>> +		n &= SAMPLE_DATA_MSK;
>> +		/* Convert the N bitstream count into voltage */
>> +		*val = (PVT_N_CONST * n - PVT_R_CONST) >> PVT_CONV_BITS;
>> +
>> +		return 0;
>> +	default:
>> +		return -EOPNOTSUPP;
>> +	}
>> +}
>> +
>> +static int pvt_read(struct device *dev, enum hwmon_sensor_types type,
>> +		    u32 attr, int channel, long *val)
>> +{
>> +	switch (type) {
>> +	case hwmon_temp:
>> +		return pvt_read_temp(dev, attr, channel, val);
>> +	case hwmon_in:
>> +		return pvt_read_in(dev, attr, channel, val);
>> +	default:
>> +		return -EOPNOTSUPP;
>> +	}
>> +}
>> +
>> +static const u32 pvt_chip_config[] = {
>> +	HWMON_C_REGISTER_TZ,
>> +	0
>> +};
>> +
>> +static const struct hwmon_channel_info pvt_chip = {
>> +	.type = hwmon_chip,
>> +	.config = pvt_chip_config,
>> +};
>> +
>> +static struct hwmon_channel_info pvt_temp = {
>> +	.type = hwmon_temp,
>> +};
>> +
>> +static struct hwmon_channel_info pvt_in = {
>> +	.type = hwmon_in,
>> +};
>> +
>> +static const struct hwmon_ops pvt_hwmon_ops = {
>> +	.is_visible = pvt_is_visible,
>> +	.read = pvt_read,
>> +};
>> +
>> +static struct hwmon_chip_info pvt_chip_info = {
>> +	.ops = &pvt_hwmon_ops,
>> +};
>> +
>> +static int pvt_init(struct pvt_device *pvt)
>> +{
>> +	u16 sys_freq, key, middle, low = 4, high = 8;
>> +	struct regmap *t_map = pvt->t_map;
>> +	struct regmap *p_map = pvt->p_map;
>> +	struct regmap *v_map = pvt->v_map;
>> +	u32 t_num = pvt->t_num;
>> +	u32 p_num = pvt->p_num;
>> +	u32 v_num = pvt->v_num;
>> +	u32 clk_synth, val;
>> +	int ret;
>> +
>> +	sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ;
>> +	while (high >= low) {
>> +		middle = (low + high + 1) / 2;
>> +		key = DIV_ROUND_CLOSEST(sys_freq, middle);
>> +		if (key > CLK_SYS_CYCLES_MAX) {
>> +			low = middle + 1;
>> +			continue;
>> +		} else if (key < CLK_SYS_CYCLES_MIN) {
>> +			high = middle - 1;
>> +			continue;
>> +		}
>> +
>> +		break;
>> +	}
>> +
>> +	/*
>> +	 * The system supports 'clk_sys' to 'clk_ip' frequency ratios
>> +	 * from 2:1 to 512:1
>> +	 */
>> +	key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2;
>> +
>> +	clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT |
>> +		    (key >> 1) << CLK_SYNTH_HI_SFT |
>> +		    (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN;
>> +
>> +	pvt->ip_freq = sys_freq * 100 / (key + 2);
>> +
>> +	if (t_num) {
>> +		regmap_write(t_map, SDIF_SMPL_CTRL, 0x0);
>> +		regmap_write(t_map, SDIF_HALT, 0x0);
>> +		regmap_write(t_map, CLK_SYNTH, clk_synth);
>> +		regmap_write(t_map, SDIF_DISABLE, 0x0);
>> +
> regmap_write can return an error. If this doesn't apply here for some reason
> (same as the reads), please add a note to the top of the driver explaining
> the reason.
>
>> +		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
>> +					       val, !(val & SDIF_BUSY),
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT |
>> +		      IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG;
>> +		regmap_write(t_map, SDIF_W, val);
>> +
>> +		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
>> +					       val, !(val & SDIF_BUSY),
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT |
>> +			      SDIF_WRN_W | SDIF_PROG;
>> +		regmap_write(t_map, SDIF_W, val);
>> +
>> +		ret = regmap_read_poll_timeout(t_map, SDIF_STAT,
>> +					       val, !(val & SDIF_BUSY),
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		val = IP_RST_REL | IP_RUN_CONT | IP_AUTO |
>> +		      IP_CTRL << SDIF_ADDR_SFT |
>> +		      SDIF_WRN_W | SDIF_PROG;
>> +		regmap_write(t_map, SDIF_W, val);
>> +	}
>> +
>> +	if (p_num) {
>> +		regmap_write(p_map, SDIF_HALT, 0x0);
>> +		regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1);
>> +		regmap_write(p_map, CLK_SYNTH, clk_synth);
>> +	}
>> +
>> +	if (v_num) {
>> +		regmap_write(v_map, SDIF_SMPL_CTRL, 0x0);
>> +		regmap_write(v_map, SDIF_HALT, 0x0);
>> +		regmap_write(v_map, CLK_SYNTH, clk_synth);
>> +		regmap_write(v_map, SDIF_DISABLE, 0x0);
>> +
>> +		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
>> +					       val, !(val & SDIF_BUSY),
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT |
>> +		      CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT |
>> +		      SDIF_WRN_W | SDIF_PROG;
>> +		regmap_write(v_map, SDIF_W, val);
>> +
>> +		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
>> +					       val, !(val & SDIF_BUSY),
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT |
>> +		      SDIF_WRN_W | SDIF_PROG;
>> +		regmap_write(v_map, SDIF_W, val);
>> +
>> +		ret = regmap_read_poll_timeout(v_map, SDIF_STAT,
>> +					       val, !(val & SDIF_BUSY),
>> +					       PVT_POLL_DELAY_US,
>> +					       PVT_POLL_TIMEOUT_US);
>> +		if (ret)
>> +			return ret;
>> +
>> +		val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE |
>> +		      IP_CTRL << SDIF_ADDR_SFT |
>> +		      SDIF_WRN_W | SDIF_PROG;
>> +		regmap_write(v_map, SDIF_W, val);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static struct regmap_config pvt_regmap_config = {
>> +	.reg_bits = 32,
>> +	.reg_stride = 4,
>> +	.val_bits = 32,
>> +};
>> +
>> +static int pvt_get_regmap(struct platform_device *pdev, char *reg_name,
>> +			  struct pvt_device *pvt)
>> +{
>> +	struct device *dev = &pdev->dev;
>> +	struct regmap **reg_map;
>> +	void __iomem *io_base;
>> +
>> +	if (!strcmp(reg_name, "common"))
>> +		reg_map = &pvt->c_map;
>> +	else if (!strcmp(reg_name, "ts"))
>> +		reg_map = &pvt->t_map;
>> +	else if (!strcmp(reg_name, "pd"))
>> +		reg_map = &pvt->p_map;
>> +	else if (!strcmp(reg_name, "vm"))
>> +		reg_map = &pvt->v_map;
>> +	else
>> +		return -EINVAL;
>> +
>> +	io_base = devm_platform_ioremap_resource_byname(pdev, reg_name);
>> +	if (IS_ERR(io_base))
>> +		return PTR_ERR(io_base);
>> +
>> +	pvt_regmap_config.name = reg_name;
> This may be convenient, but I am concerned that it might cause trouble if there
> is more than one such controller in the system. Can you confirm that there will
> always be one, and exactly one, such device in any given system ?

Yes, it is confirmed that there will be only one and exactly one such controller
in any given system.

>> +	*reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config);
>> +	if (IS_ERR(*reg_map)) {
>> +		dev_err(dev, "failed to init register map\n");
>> +		return PTR_ERR(*reg_map);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static void pvt_clk_disable(void *data)
>> +{
>> +	struct pvt_device *pvt = data;
>> +
>> +	clk_disable_unprepare(pvt->clk);
>> +}
>> +
>> +static int pvt_clk_enable(struct device *dev, struct pvt_device *pvt)
>> +{
>> +	int ret;
>> +
>> +	ret = clk_prepare_enable(pvt->clk);
>> +	if (ret)
>> +		return ret;
>> +
>> +	return devm_add_action_or_reset(dev, pvt_clk_disable, pvt);
>> +}
>> +
>> +static void pvt_reset_control_assert(void *data)
>> +{
>> +	struct pvt_device *pvt = data;
>> +
>> +	reset_control_assert(pvt->rst);
>> +}
>> +
>> +static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt)
>> +{
>> +	int ret;
>> +
>> +	ret = reset_control_deassert(pvt->rst);
>> +	if (ret)
>> +		return ret;
>> +
>> +	return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt);
>> +}
>> +
>> +static int mr75203_probe(struct platform_device *pdev)
>> +{
>> +	const struct hwmon_channel_info **pvt_info;
>> +	u32 ts_num, vm_num, pd_num, val, index, i;
>> +	struct device *dev = &pdev->dev;
>> +	u32 *temp_config, *in_config;
>> +	struct device *hwmon_dev;
>> +	struct pvt_device *pvt;
>> +	int ret;
>> +
>> +	pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL);
>> +	if (!pvt)
>> +		return -ENOMEM;
>> +
>> +	ret = pvt_get_regmap(pdev, "common", pvt);
>> +	if (ret)
>> +		return ret;
>> +
>> +	pvt->clk = devm_clk_get(dev, NULL);
>> +	if (IS_ERR(pvt->clk))
>> +		return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n");
>> +
>> +	ret = pvt_clk_enable(dev, pvt);
>> +	if (ret) {
>> +		dev_err(dev, "failed to enable clock\n");
>> +		return ret;
>> +	}
>> +
>> +	pvt->rst = devm_reset_control_get_exclusive(dev, NULL);
>> +	if (IS_ERR(pvt->rst))
>> +		return dev_err_probe(dev, PTR_ERR(pvt->rst),
>> +				     "failed to get reset control\n");
>> +
>> +	ret = pvt_reset_control_deassert(dev, pvt);
>> +	if (ret)
>> +		return dev_err_probe(dev, ret, "cannot deassert reset control\n");
>> +
>> +	regmap_read(pvt->c_map, PVT_IP_CONFIG, &val);
>> +	ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT;
>> +	pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT;
>> +	vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT;
>> +	pvt->t_num = ts_num;
>> +	pvt->p_num = pd_num;
>> +	pvt->v_num = vm_num;
>> +	val = 0;
>> +	if (ts_num)
>> +		val++;
>> +	if (vm_num)
>> +		val++;
>> +	if (!val)
>> +		return -ENODEV;
>> +
>> +	pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL);
>> +	if (!pvt_info)
>> +		return -ENOMEM;
>> +	pvt_info[0] = &pvt_chip;
>> +	index = 1;
>> +
>> +	if (ts_num) {
>> +		ret = pvt_get_regmap(pdev, "ts", pvt);
>> +		if (ret)
>> +			return ret;
>> +
>> +		temp_config = devm_kcalloc(dev, ts_num + 1,
>> +					   sizeof(*temp_config), GFP_KERNEL);
>> +		if (!temp_config)
>> +			return -ENOMEM;
>> +
>> +		for (i = 0; i < ts_num; i++)
>> +			temp_config[i] = HWMON_T_INPUT;
>> +
>> +		temp_config[ts_num] = 0;
>> +		pvt_temp.config = temp_config;
>> +
>> +		pvt_info[index++] = &pvt_temp;
>> +	}
>> +
>> +	if (pd_num) {
>> +		ret = pvt_get_regmap(pdev, "pd", pvt);
>> +		if (ret)
>> +			return ret;
>> +	}
>> +
>> +	if (vm_num) {
>> +		u32 num = vm_num;
>> +
>> +		ret = pvt_get_regmap(pdev, "vm", pvt);
>> +		if (ret)
>> +			return ret;
>> +
>> +		pvt->vm_idx = devm_kcalloc(dev, vm_num, sizeof(*pvt->vm_idx),
>> +					   GFP_KERNEL);
>> +		if (!pvt->vm_idx)
>> +			return -ENOMEM;
>> +
>> +		for (i = 0; i < vm_num; i++)
>> +			pvt->vm_idx[i] = i;
>> +
>> +		ret = device_property_read_u8_array(dev, "intel,vm-map",
>> +						    pvt->vm_idx, vm_num);
>> +		if (!ret)
>> +			for (i = 0; i < vm_num; i++)
>> +				if (pvt->vm_idx[i] >= vm_num ||
>> +				    pvt->vm_idx[i] == 0xff) {
>> +					num = i;
>> +					break;
>> +				}
>> +
>> +		in_config = devm_kcalloc(dev, num + 1,
>> +					 sizeof(*in_config), GFP_KERNEL);
>> +		if (!in_config)
>> +			return -ENOMEM;
>> +
>> +		memset32(in_config, HWMON_I_INPUT, num);
>> +		in_config[num] = 0;
>> +		pvt_in.config = in_config;
>> +
>> +		pvt_info[index++] = &pvt_in;
>> +	}
>> +
>> +	ret = pvt_init(pvt);
>> +	if (ret) {
>> +		dev_err(dev, "failed to init pvt: %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	pvt_chip_info.info = pvt_info;
>> +	hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt",
>> +							 pvt,
>> +							 &pvt_chip_info,
>> +							 NULL);
>> +
>> +	return PTR_ERR_OR_ZERO(hwmon_dev);
>> +}
>> +
>> +static const struct of_device_id moortec_pvt_of_match[] = {
>> +	{ .compatible = "moortec,mr75203" },
>> +	{ }
>> +};
>> +MODULE_DEVICE_TABLE(of, moortec_pvt_of_match);
>> +
>> +static struct platform_driver moortec_pvt_driver = {
>> +	.driver = {
>> +		.name = "moortec-pvt",
>> +		.of_match_table = moortec_pvt_of_match,
>> +	},
>> +	.probe = mr75203_probe,
>> +};
>> +module_platform_driver(moortec_pvt_driver);
>> +
>> +MODULE_LICENSE("GPL v2");
>>

Thanks.

Regards,
Rahul