Re: [PATCH v2 2/4] net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver
From: Heiner Kallweit
Date: Sat Oct 03 2020 - 08:59:19 EST
On 02.10.2020 21:22, Łukasz Stelmach wrote:
> ASIX AX88796[1] is a versatile ethernet adapter chip, that can be
> connected to a CPU with a 8/16-bit bus or with an SPI. This driver
> supports SPI connection.
>
> The driver has been ported from the vendor kernel for ARTIK5[2]
> boards. Several changes were made to adapt it to the current kernel
> which include:
>
> + updated DT configuration,
> + clock configuration moved to DT,
> + new timer, ethtool and gpio APIs,
> + dev_* instead of pr_* and custom printk() wrappers,
> + removed awkward vendor power managemtn.
>
> [1] https://www.asix.com.tw/products.php?op=pItemdetail&PItemID=104;65;86&PLine=65
> [2] https://git.tizen.org/cgit/profile/common/platform/kernel/linux-3.10-artik/
>
> The other ax88796 driver is for NE2000 compatible AX88796L chip. These
> chips are not compatible. Hence, two separate drivers are required.
>
> Signed-off-by: Łukasz Stelmach <l.stelmach@xxxxxxxxxxx>
> ---
> MAINTAINERS | 6 +
> drivers/net/ethernet/Kconfig | 1 +
> drivers/net/ethernet/Makefile | 1 +
> drivers/net/ethernet/asix/Kconfig | 21 +
> drivers/net/ethernet/asix/Makefile | 6 +
> drivers/net/ethernet/asix/ax88796c_ioctl.c | 241 +++++
> drivers/net/ethernet/asix/ax88796c_ioctl.h | 27 +
> drivers/net/ethernet/asix/ax88796c_main.c | 1041 ++++++++++++++++++++
> drivers/net/ethernet/asix/ax88796c_main.h | 568 +++++++++++
> drivers/net/ethernet/asix/ax88796c_spi.c | 111 +++
> drivers/net/ethernet/asix/ax88796c_spi.h | 69 ++
> 11 files changed, 2092 insertions(+)
> create mode 100644 drivers/net/ethernet/asix/Kconfig
> create mode 100644 drivers/net/ethernet/asix/Makefile
> create mode 100644 drivers/net/ethernet/asix/ax88796c_ioctl.c
> create mode 100644 drivers/net/ethernet/asix/ax88796c_ioctl.h
> create mode 100644 drivers/net/ethernet/asix/ax88796c_main.c
> create mode 100644 drivers/net/ethernet/asix/ax88796c_main.h
> create mode 100644 drivers/net/ethernet/asix/ax88796c_spi.c
> create mode 100644 drivers/net/ethernet/asix/ax88796c_spi.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index deaafb617361..654eb0127479 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2822,6 +2822,12 @@ S: Maintained
> F: Documentation/hwmon/asc7621.rst
> F: drivers/hwmon/asc7621.c
>
> +ASIX AX88796C SPI ETHERNET ADAPTER
> +M: Łukasz Stelmach <l.stelmach@xxxxxxxxxxx>
> +S: Maintained
> +F: Documentation/devicetree/bindings/net/asix,ax99706c-spi.yaml
> +F: drivers/net/ethernet/asix/ax88796c_*
> +
> ASPEED PINCTRL DRIVERS
> M: Andrew Jeffery <andrew@xxxxxxxx>
> L: linux-aspeed@xxxxxxxxxxxxxxxx (moderated for non-subscribers)
> diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
> index de50e8b9e656..f3b218e45ea5 100644
> --- a/drivers/net/ethernet/Kconfig
> +++ b/drivers/net/ethernet/Kconfig
> @@ -32,6 +32,7 @@ source "drivers/net/ethernet/apm/Kconfig"
> source "drivers/net/ethernet/apple/Kconfig"
> source "drivers/net/ethernet/aquantia/Kconfig"
> source "drivers/net/ethernet/arc/Kconfig"
> +source "drivers/net/ethernet/asix/Kconfig"
> source "drivers/net/ethernet/atheros/Kconfig"
> source "drivers/net/ethernet/aurora/Kconfig"
> source "drivers/net/ethernet/broadcom/Kconfig"
> diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
> index f8f38dcb5f8a..9eb368d93607 100644
> --- a/drivers/net/ethernet/Makefile
> +++ b/drivers/net/ethernet/Makefile
> @@ -18,6 +18,7 @@ obj-$(CONFIG_NET_XGENE) += apm/
> obj-$(CONFIG_NET_VENDOR_APPLE) += apple/
> obj-$(CONFIG_NET_VENDOR_AQUANTIA) += aquantia/
> obj-$(CONFIG_NET_VENDOR_ARC) += arc/
> +obj-$(CONFIG_NET_VENDOR_ASIX) += asix/
> obj-$(CONFIG_NET_VENDOR_ATHEROS) += atheros/
> obj-$(CONFIG_NET_VENDOR_AURORA) += aurora/
> obj-$(CONFIG_NET_VENDOR_CADENCE) += cadence/
> diff --git a/drivers/net/ethernet/asix/Kconfig b/drivers/net/ethernet/asix/Kconfig
> new file mode 100644
> index 000000000000..7caa45607450
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/Kconfig
> @@ -0,0 +1,21 @@
> +#
> +# Asix network device configuration
> +#
> +
> +config NET_VENDOR_ASIX
> + bool "Asix devices"
> + default y
> + help
> + If you have a network (Ethernet, non-USB, not NE2000 compatible)
> + interface based on a chip from ASIX, say Y.
> +
> +if NET_VENDOR_ASIX
> +
> +config SPI_AX88796C
> + tristate "Asix AX88796C-SPI support"
> + depends on SPI
> + depends on GPIOLIB
> + help
> + Say Y here if you intend to use ASIX AX88796C attached in SPI mode.
> +
> +endif # NET_VENDOR_ASIX
> diff --git a/drivers/net/ethernet/asix/Makefile b/drivers/net/ethernet/asix/Makefile
> new file mode 100644
> index 000000000000..0bfbbb042634
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/Makefile
> @@ -0,0 +1,6 @@
> +#
> +# Makefile for the Asix network device drivers.
> +#
> +
> +obj-$(CONFIG_SPI_AX88796C) += ax88796c.o
> +ax88796c-y := ax88796c_main.o ax88796c_ioctl.o ax88796c_spi.o
> diff --git a/drivers/net/ethernet/asix/ax88796c_ioctl.c b/drivers/net/ethernet/asix/ax88796c_ioctl.c
> new file mode 100644
> index 000000000000..b3e3ac96790d
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/ax88796c_ioctl.c
> @@ -0,0 +1,241 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2010 ASIX Electronics Corporation
> + * Copyright (c) 2020 Samsung Electronics Co., Ltd.
> + *
> + * ASIX AX88796C SPI Fast Ethernet Linux driver
> + */
> +
> +#define pr_fmt(fmt) "ax88796c: " fmt
> +
> +#include <linux/bitmap.h>
> +#include <linux/iopoll.h>
> +#include <linux/phy.h>
> +#include <linux/netdevice.h>
> +
> +#include "ax88796c_main.h"
> +#include "ax88796c_ioctl.h"
> +
> +static void ax88796c_get_drvinfo(struct net_device *ndev,
> + struct ethtool_drvinfo *info)
> +{
> + /* Inherit standard device info */
> + strncpy(info->driver, DRV_NAME, sizeof(info->driver));
> +}
> +
> +static u32 ax88796c_get_link(struct net_device *ndev)
Why not using ethtool_op_get_link ?
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + phy_read_status(ndev->phydev);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return ndev->phydev->link;
> +}
> +
> +static u32 ax88796c_get_msglevel(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + return ax_local->msg_enable;
> +}
> +
> +static void ax88796c_set_msglevel(struct net_device *ndev, u32 level)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + ax_local->msg_enable = level;
> +}
> +
> +static int
> +ax88796c_get_link_ksettings(struct net_device *ndev,
> + struct ethtool_link_ksettings *cmd)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + int ret;
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + ret = phy_ethtool_get_link_ksettings(ndev, cmd);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return ret;
> +}
> +
> +static int
> +ax88796c_set_link_ksettings(struct net_device *ndev,
> + const struct ethtool_link_ksettings *cmd)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + int ret;
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + ret = phy_ethtool_set_link_ksettings(ndev, cmd);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return ret;
> +}
> +
> +static int ax88796c_nway_reset(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + int ret;
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + ret = phy_ethtool_nway_reset(ndev);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return ret;
> +}
> +
> +static u32 ax88796c_ethtool_getmsglevel(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + return ax_local->msg_enable;
> +}
> +
> +static void ax88796c_ethtool_setmsglevel(struct net_device *ndev, u32 level)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + ax_local->msg_enable = level;
> +}
> +
> +static int ax88796c_get_regs_len(struct net_device *ndev)
> +{
> + return AX88796C_REGDUMP_LEN + AX88796C_PHY_REGDUMP_LEN;
> +}
> +
> +static void
> +ax88796c_get_regs(struct net_device *ndev, struct ethtool_regs *regs, void *_p)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + u16 *p = _p;
> + int offset, i;
> +
> + memset(p, 0, AX88796C_REGDUMP_LEN);
> +
> + for (offset = 0; offset < AX88796C_REGDUMP_LEN; offset += 2) {
> + if (!test_bit(offset / 2, ax88796c_no_regs_mask))
> + *p = AX_READ(&ax_local->ax_spi, offset);
> + p++;
> + }
> +
> + for (i = 0; i < AX88796C_PHY_REGDUMP_LEN / 2; i++) {
> + *p = phy_read(ax_local->phydev, i);
> + p++;
> + }
> +}
> +
> +int ax88796c_mdio_read(struct mii_bus *mdiobus, int phy_id, int loc)
> +{
> + struct ax88796c_device *ax_local = mdiobus->priv;
> + int ret;
> +
> + AX_WRITE(&ax_local->ax_spi, MDIOCR_RADDR(loc)
> + | MDIOCR_FADDR(phy_id) | MDIOCR_READ, P2_MDIOCR);
> +
> + ret = read_poll_timeout(AX_READ, ret,
> + (ret != 0),
> + 0, jiffies_to_usecs(HZ / 100), false,
> + &ax_local->ax_spi, P2_MDIOCR);
> + if (ret)
> + return -EBUSY;
> +
> + return AX_READ(&ax_local->ax_spi, P2_MDIODR);
> +}
> +
> +int
> +ax88796c_mdio_write(struct mii_bus *mdiobus, int phy_id, int loc, u16 val)
> +{
> + struct ax88796c_device *ax_local = mdiobus->priv;
> + int ret;
> +
> + AX_WRITE(&ax_local->ax_spi, val, P2_MDIODR);
> +
> + AX_WRITE(&ax_local->ax_spi,
> + MDIOCR_RADDR(loc) | MDIOCR_FADDR(phy_id)
> + | MDIOCR_WRITE, P2_MDIOCR);
> +
> + ret = read_poll_timeout(AX_READ, ret,
> + ((ret & MDIOCR_VALID) != 0), 0,
> + jiffies_to_usecs(HZ / 100), false,
> + &ax_local->ax_spi, P2_MDIOCR);
> + if (ret)
> + return -EIO;
> +
> + if (loc == MII_ADVERTISE) {
> + AX_WRITE(&ax_local->ax_spi, (BMCR_FULLDPLX | BMCR_ANRESTART |
> + BMCR_ANENABLE | BMCR_SPEED100), P2_MDIODR);
This looks very hacky. Why do you do this?
What if the user wants to switch to fixed mode?
> + AX_WRITE(&ax_local->ax_spi, (MDIOCR_RADDR(MII_BMCR) |
> + MDIOCR_FADDR(phy_id) | MDIOCR_WRITE),
> + P2_MDIOCR);
> +
> + ret = read_poll_timeout(AX_READ, ret,
> + ((ret & MDIOCR_VALID) != 0), 0,
> + jiffies_to_usecs(HZ / 100), false,
> + &ax_local->ax_spi, P2_MDIOCR);
> + if (ret)
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +void ax88796c_set_csums(struct ax88796c_device *ax_local)
> +{
> + struct net_device *ndev = ax_local->ndev;
> +
> + if (ndev->features & NETIF_F_RXCSUM) {
> + AX_WRITE(&ax_local->ax_spi, COERCR0_DEFAULT, P4_COERCR0);
> + AX_WRITE(&ax_local->ax_spi, COERCR1_DEFAULT, P4_COERCR1);
> + } else {
> + AX_WRITE(&ax_local->ax_spi, 0, P4_COERCR0);
> + AX_WRITE(&ax_local->ax_spi, 0, P4_COERCR1);
> + }
> +
> + if (ndev->features & NETIF_F_HW_CSUM) {
> + AX_WRITE(&ax_local->ax_spi, COETCR0_DEFAULT, P4_COETCR0);
> + AX_WRITE(&ax_local->ax_spi, COETCR1_TXPPPE, P4_COETCR1);
> + } else {
> + AX_WRITE(&ax_local->ax_spi, 0, P4_COETCR0);
> + AX_WRITE(&ax_local->ax_spi, 0, P4_COETCR1);
> + }
> +}
> +
> +const struct ethtool_ops ax88796c_ethtool_ops = {
> + .get_drvinfo = ax88796c_get_drvinfo,
> + .get_link = ax88796c_get_link,
> + .get_msglevel = ax88796c_get_msglevel,
> + .set_msglevel = ax88796c_set_msglevel,
> + .get_link_ksettings = ax88796c_get_link_ksettings,
> + .set_link_ksettings = ax88796c_set_link_ksettings,
> + .nway_reset = ax88796c_nway_reset,
> + .get_msglevel = ax88796c_ethtool_getmsglevel,
> + .set_msglevel = ax88796c_ethtool_setmsglevel,
> + .get_regs_len = ax88796c_get_regs_len,
> + .get_regs = ax88796c_get_regs,
> +};
> +
> +int ax88796c_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + int ret;
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + ret = phy_mii_ioctl(ndev->phydev, ifr, cmd);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return ret;
> +}
> diff --git a/drivers/net/ethernet/asix/ax88796c_ioctl.h b/drivers/net/ethernet/asix/ax88796c_ioctl.h
> new file mode 100644
> index 000000000000..d478981bf995
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/ax88796c_ioctl.h
> @@ -0,0 +1,27 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * Copyright (c) 2010 ASIX Electronics Corporation
> + * Copyright (c) 2020 Samsung Electronics Co., Ltd.
> + *
> + * ASIX AX88796C SPI Fast Ethernet Linux driver
> + */
> +
> +#ifndef _AX88796C_IOCTL_H
> +#define _AX88796C_IOCTL_H
> +
> +#include <linux/ethtool.h>
> +#include <linux/netdevice.h>
> +
> +#include "ax88796c_main.h"
> +
> +extern const struct ethtool_ops ax88796c_ethtool_ops;
> +
> +bool ax88796c_check_power(const struct ax88796c_device *ax_local);
> +bool ax88796c_check_power_and_wake(struct ax88796c_device *ax_local);
> +void ax88796c_set_power_saving(struct ax88796c_device *ax_local, u8 ps_level);
> +int ax88796c_mdio_read(struct mii_bus *mdiobus, int phy_id, int loc);
> +int ax88796c_mdio_write(struct mii_bus *mdiobus, int phy_id, int loc, u16 val);
> +void ax88796c_set_csums(struct ax88796c_device *ax_local);
> +int ax88796c_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
> +
> +#endif
> diff --git a/drivers/net/ethernet/asix/ax88796c_main.c b/drivers/net/ethernet/asix/ax88796c_main.c
> new file mode 100644
> index 000000000000..2148ea01362a
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/ax88796c_main.c
> @@ -0,0 +1,1041 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2010 ASIX Electronics Corporation
> + * Copyright (c) 2020 Samsung Electronics Co., Ltd.
> + *
> + * ASIX AX88796C SPI Fast Ethernet Linux driver
> + */
> +
> +#define pr_fmt(fmt) "ax88796c: " fmt
> +
> +#include "ax88796c_main.h"
> +#include "ax88796c_ioctl.h"
> +
> +#include <linux/bitmap.h>
> +#include <linux/etherdevice.h>
> +#include <linux/iopoll.h>
> +#include <linux/mdio.h>
> +#include <linux/module.h>
> +#include <linux/netdevice.h>
> +#include <linux/of.h>
> +#include <linux/phy.h>
> +#include <linux/spi/spi.h>
> +
> +static int comp;
> +static int msg_enable = NETIF_MSG_PROBE |
> + NETIF_MSG_LINK |
> + /* NETIF_MSG_TIMER | */
> + /* NETIF_MSG_IFDOWN | */
> + /* NETIF_MSG_IFUP | */
> + NETIF_MSG_RX_ERR |
> + NETIF_MSG_TX_ERR |
> + /* NETIF_MSG_TX_QUEUED | */
> + /* NETIF_MSG_INTR | */
> + /* NETIF_MSG_TX_DONE | */
> + /* NETIF_MSG_RX_STATUS | */
> + /* NETIF_MSG_PKTDATA | */
> + /* NETIF_MSG_HW | */
> + /* NETIF_MSG_WOL | */
> + 0;
> +
> +static char *no_regs_list = "80018001,e1918001,8001a001,fc0d0000";
> +unsigned long ax88796c_no_regs_mask[AX88796C_REGDUMP_LEN / (sizeof(unsigned long) * 8)];
> +
> +module_param(comp, int, 0444);
> +MODULE_PARM_DESC(comp, "0=Non-Compression Mode, 1=Compression Mode");
> +
> +module_param(msg_enable, int, 0444);
> +MODULE_PARM_DESC(msg_enable, "Message mask (see linux/netdevice.h for bitmap)");
> +
> +static int ax88796c_soft_reset(struct ax88796c_device *ax_local)
> +{
> + u16 temp;
> + int ret;
> +
> + AX_WRITE(&ax_local->ax_spi, PSR_RESET, P0_PSR);
> + AX_WRITE(&ax_local->ax_spi, PSR_RESET_CLR, P0_PSR);
> +
> + ret = read_poll_timeout(AX_READ, ret,
> + (ret & PSR_DEV_READY),
> + 0, jiffies_to_usecs(160 * HZ / 1000), false,
> + &ax_local->ax_spi, P0_PSR);
> + if (ret)
> + return -1;
> +
> + temp = AX_READ(&ax_local->ax_spi, P4_SPICR);
> + if (ax_local->capabilities & AX_CAP_COMP) {
> + AX_WRITE(&ax_local->ax_spi,
> + (temp | SPICR_RCEN | SPICR_QCEN), P4_SPICR);
> + ax_local->ax_spi.comp = 1;
> + } else {
> + AX_WRITE(&ax_local->ax_spi,
> + (temp & ~(SPICR_RCEN | SPICR_QCEN)), P4_SPICR);
> + ax_local->ax_spi.comp = 0;
> + }
> +
> + return 0;
> +}
> +
> +static int ax88796c_reload_eeprom(struct ax88796c_device *ax_local)
> +{
> + int ret;
> +
> + AX_WRITE(&ax_local->ax_spi, EECR_RELOAD, P3_EECR);
> +
> + ret = read_poll_timeout(AX_READ, ret,
> + (ret & PSR_DEV_READY),
> + 0, jiffies_to_usecs(2 * HZ / 1000), false,
> + &ax_local->ax_spi, P0_PSR);
> + if (ret) {
> + dev_err(&ax_local->spi->dev,
> + "timeout waiting for reload eeprom\n");
> + return -1;
> + }
> +
> + return 0;
> +}
> +
> +static void ax88796c_set_hw_multicast(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + u16 rx_ctl = RXCR_AB;
> + int mc_count = netdev_mc_count(ndev);
> +
> + memset(ax_local->multi_filter, 0, AX_MCAST_FILTER_SIZE);
> +
> + if (ndev->flags & IFF_PROMISC) {
> + rx_ctl |= RXCR_PRO;
> +
> + } else if (ndev->flags & IFF_ALLMULTI || mc_count > AX_MAX_MCAST) {
> + rx_ctl |= RXCR_AMALL;
> +
> + } else if (mc_count == 0) {
> + /* just broadcast and directed */
> + } else {
> + u32 crc_bits;
> + int i;
> + struct netdev_hw_addr *ha;
> +
> + netdev_for_each_mc_addr(ha, ndev) {
> + crc_bits = ether_crc(ETH_ALEN, ha->addr);
> + ax_local->multi_filter[crc_bits >> 29] |=
> + (1 << ((crc_bits >> 26) & 7));
> + }
> +
> + for (i = 0; i < 4; i++) {
> + AX_WRITE(&ax_local->ax_spi,
> + ((ax_local->multi_filter[i * 2 + 1] << 8) |
> + ax_local->multi_filter[i * 2]), P3_MFAR(i));
> + }
> + }
> +
> + AX_WRITE(&ax_local->ax_spi, rx_ctl, P2_RXCR);
> +}
> +
> +static void ax88796c_set_mac_addr(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + AX_WRITE(&ax_local->ax_spi, ((u16)(ndev->dev_addr[4] << 8) |
> + (u16)ndev->dev_addr[5]), P3_MACASR0);
> + AX_WRITE(&ax_local->ax_spi, ((u16)(ndev->dev_addr[2] << 8) |
> + (u16)ndev->dev_addr[3]), P3_MACASR1);
> + AX_WRITE(&ax_local->ax_spi, ((u16)(ndev->dev_addr[0] << 8) |
> + (u16)ndev->dev_addr[1]), P3_MACASR2);
> +}
> +
> +static int ax88796c_set_mac_address(struct net_device *ndev, void *p)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + struct sockaddr *addr = p;
> +
> + if (!is_valid_ether_addr(addr->sa_data))
> + return -EADDRNOTAVAIL;
> +
> + memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len);
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + ax88796c_set_mac_addr(ndev);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return 0;
> +}
> +
> +static void ax88796c_load_mac_addr(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + u16 temp;
> +
> + /* Try the device tree first */
> + if (!eth_platform_get_mac_address(&ax_local->spi->dev, ndev->dev_addr) &&
> + is_valid_ether_addr(ndev->dev_addr)) {
> + if (netif_msg_probe(ax_local))
> + dev_info(&ax_local->spi->dev,
> + "MAC address read from device tree\n");
> + return;
> + }
> +
> + /* Read the MAC address from AX88796C */
> + temp = AX_READ(&ax_local->ax_spi, P3_MACASR0);
> + ndev->dev_addr[5] = (u8)temp;
> + ndev->dev_addr[4] = (u8)(temp >> 8);
> +
> + temp = AX_READ(&ax_local->ax_spi, P3_MACASR1);
> + ndev->dev_addr[3] = (u8)temp;
> + ndev->dev_addr[2] = (u8)(temp >> 8);
> +
> + temp = AX_READ(&ax_local->ax_spi, P3_MACASR2);
> + ndev->dev_addr[1] = (u8)temp;
> + ndev->dev_addr[0] = (u8)(temp >> 8);
> +
> + if (is_valid_ether_addr(ndev->dev_addr)) {
> + if (netif_msg_probe(ax_local))
> + dev_info(&ax_local->spi->dev,
> + "MAC address read from ASIX chip\n");
> + return;
> + }
> +
> + /* Use random address if none found */
> + if (netif_msg_probe(ax_local))
> + dev_info(&ax_local->spi->dev, "Use random MAC address\n");
> + eth_hw_addr_random(ndev);
> +}
> +
> +static void ax88796c_proc_tx_hdr(struct tx_pkt_info *info, u8 ip_summed)
> +{
> + u16 pkt_len_bar = (~info->pkt_len & TX_HDR_SOP_PKTLENBAR);
> +
> + /* Prepare SOP header */
> + info->sop.flags_len = info->pkt_len |
> + ((ip_summed == CHECKSUM_NONE) ||
> + (ip_summed == CHECKSUM_UNNECESSARY) ? TX_HDR_SOP_DICF : 0);
> +
> + info->sop.seq_lenbar = ((info->seq_num << 11) & TX_HDR_SOP_SEQNUM)
> + | pkt_len_bar;
> + cpu_to_be16s(&info->sop.flags_len);
> + cpu_to_be16s(&info->sop.seq_lenbar);
> +
> + /* Prepare Segment header */
> + info->seg.flags_seqnum_seglen = TX_HDR_SEG_FS | TX_HDR_SEG_LS
> + | info->pkt_len;
> +
> + info->seg.eo_so_seglenbar = pkt_len_bar;
> +
> + cpu_to_be16s(&info->seg.flags_seqnum_seglen);
> + cpu_to_be16s(&info->seg.eo_so_seglenbar);
> +
> + /* Prepare EOP header */
> + info->eop.seq_len = ((info->seq_num << 11) &
> + TX_HDR_EOP_SEQNUM) | info->pkt_len;
> + info->eop.seqbar_lenbar = ((~info->seq_num << 11) &
> + TX_HDR_EOP_SEQNUMBAR) | pkt_len_bar;
> +
> + cpu_to_be16s(&info->eop.seq_len);
> + cpu_to_be16s(&info->eop.seqbar_lenbar);
> +}
> +
> +static int
> +ax88796c_check_free_pages(struct ax88796c_device *ax_local, u8 need_pages)
> +{
> + u8 free_pages;
> + u16 tmp;
> +
> + free_pages = AX_READ(&ax_local->ax_spi, P0_TFBFCR) & TX_FREEBUF_MASK;
> + if (free_pages < need_pages) {
> + /* schedule free page interrupt */
> + tmp = AX_READ(&ax_local->ax_spi, P0_TFBFCR)
> + & TFBFCR_SCHE_FREE_PAGE;
> + AX_WRITE(&ax_local->ax_spi, tmp | TFBFCR_TX_PAGE_SET |
> + TFBFCR_SET_FREE_PAGE(need_pages),
> + P0_TFBFCR);
> + return -ENOMEM;
> + }
> +
> + return 0;
> +}
> +
> +static struct sk_buff *
> +ax88796c_tx_fixup(struct net_device *ndev, struct sk_buff_head *q)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + struct sk_buff *skb, *tx_skb;
> + struct tx_pkt_info *info;
> + struct skb_data *entry;
> + int headroom;
> + int tailroom;
> + u8 need_pages;
> + u16 tol_len, pkt_len;
> + u8 padlen, seq_num;
> + u8 spi_len = ax_local->ax_spi.comp ? 1 : 4;
> +
> + if (skb_queue_empty(q))
> + return NULL;
> +
> + skb = skb_peek(q);
> + pkt_len = skb->len;
> + need_pages = (pkt_len + TX_OVERHEAD + 127) >> 7;
> + if (ax88796c_check_free_pages(ax_local, need_pages) != 0)
> + return NULL;
> +
> + headroom = skb_headroom(skb);
> + tailroom = skb_tailroom(skb);
> + padlen = ((pkt_len + 3) & 0x7FC) - pkt_len;
> + tol_len = ((pkt_len + 3) & 0x7FC) +
> + TX_OVERHEAD + TX_EOP_SIZE + spi_len;
> + seq_num = ++ax_local->seq_num & 0x1F;
> +
> + info = (struct tx_pkt_info *)skb->cb;
> + info->pkt_len = pkt_len;
> +
> + if ((!skb_cloned(skb)) &&
> + (headroom >= (TX_OVERHEAD + spi_len)) &&
> + (tailroom >= (padlen + TX_EOP_SIZE))) {
> + info->seq_num = seq_num;
> + ax88796c_proc_tx_hdr(info, skb->ip_summed);
> +
> + /* SOP and SEG header */
> + memcpy(skb_push(skb, TX_OVERHEAD), &info->sop, TX_OVERHEAD);
> +
> + /* Write SPI TXQ header */
> + memcpy(skb_push(skb, spi_len), tx_cmd_buf, spi_len);
> +
> + /* Make 32-bit alignment */
> + skb_put(skb, padlen);
> +
> + /* EOP header */
> + memcpy(skb_put(skb, TX_EOP_SIZE), &info->eop, TX_EOP_SIZE);
> +
> + tx_skb = skb;
> + skb_unlink(skb, q);
> + } else {
> + tx_skb = alloc_skb(tol_len, GFP_KERNEL);
Are you sure GFP_KERNEL is appropriate here and you don't have
to use GFP_ATOMIC?
> + if (!tx_skb)
> + return NULL;
> +
> + /* Write SPI TXQ header */
> + memcpy(skb_put(tx_skb, spi_len), tx_cmd_buf, spi_len);
> +
> + info->seq_num = seq_num;
> + ax88796c_proc_tx_hdr(info, skb->ip_summed);
> +
> + /* SOP and SEG header */
> + memcpy(skb_put(tx_skb, TX_OVERHEAD),
> + &info->sop, TX_OVERHEAD);
> +
> + /* Packet */
> + memcpy(skb_put(tx_skb, ((pkt_len + 3) & 0xFFFC)),
> + skb->data, pkt_len);
> +
> + /* EOP header */
> + memcpy(skb_put(tx_skb, TX_EOP_SIZE),
> + &info->eop, TX_EOP_SIZE);
> +
> + skb_unlink(skb, q);
> + dev_kfree_skb(skb);
> + }
> +
> + entry = (struct skb_data *)tx_skb->cb;
> + memset(entry, 0, sizeof(*entry));
> + entry->len = pkt_len;
> +
> + if (netif_msg_pktdata(ax_local)) {
> + char pfx[IFNAMSIZ + 7];
> +
> + snprintf(pfx, sizeof(pfx), "%s: ", ndev->name);
> +
> + netdev_info(ndev, "TX packet len %d, total len %d, seq %d\n",
> + pkt_len, tx_skb->len, seq_num);
> +
> + netdev_info(ndev, " SPI Header:\n");
> + print_hex_dump(KERN_INFO, pfx, DUMP_PREFIX_OFFSET, 16, 1,
> + tx_skb->data, 4, 0);
> +
> + netdev_info(ndev, " TX SOP:\n");
> + print_hex_dump(KERN_INFO, pfx, DUMP_PREFIX_OFFSET, 16, 1,
> + tx_skb->data + 4, TX_OVERHEAD, 0);
> +
> + netdev_info(ndev, " TX packet:\n");
> + print_hex_dump(KERN_INFO, pfx, DUMP_PREFIX_OFFSET, 16, 1,
> + tx_skb->data + 4 + TX_OVERHEAD,
> + tx_skb->len - TX_EOP_SIZE - 4 - TX_OVERHEAD, 0);
> +
> + netdev_info(ndev, " TX EOP:\n");
> + print_hex_dump(KERN_INFO, pfx, DUMP_PREFIX_OFFSET, 16, 1,
> + tx_skb->data + tx_skb->len - 4, 4, 0);
> + }
> +
> + return tx_skb;
> +}
> +
> +static int ax88796c_hard_xmit(struct ax88796c_device *ax_local)
> +{
> + struct sk_buff *tx_skb;
> + struct skb_data *entry;
> +
> + tx_skb = ax88796c_tx_fixup(ax_local->ndev, &ax_local->tx_wait_q);
> +
> + if (!tx_skb)
> + return 0;
> +
> + entry = (struct skb_data *)tx_skb->cb;
> +
> + AX_WRITE(&ax_local->ax_spi,
> + (TSNR_TXB_START | TSNR_PKT_CNT(1)), P0_TSNR);
> +
> + axspi_write_txq(&ax_local->ax_spi, tx_skb->data, tx_skb->len);
> +
> + if (((AX_READ(&ax_local->ax_spi, P0_TSNR) & TXNR_TXB_IDLE) == 0) ||
> + ((ISR_TXERR & AX_READ(&ax_local->ax_spi, P0_ISR)) != 0)) {
> + /* Ack tx error int */
> + AX_WRITE(&ax_local->ax_spi, ISR_TXERR, P0_ISR);
> +
> + ax_local->stats.tx_dropped++;
> +
> + netif_err(ax_local, tx_err, ax_local->ndev,
> + "TX FIFO error, re-initialize the TX bridge\n");
> +
> + /* Reinitial tx bridge */
> + AX_WRITE(&ax_local->ax_spi, TXNR_TXB_REINIT |
> + AX_READ(&ax_local->ax_spi, P0_TSNR), P0_TSNR);
> + ax_local->seq_num = 0;
> + } else {
> + ax_local->stats.tx_packets++;
> + ax_local->stats.tx_bytes += entry->len;
> + }
> +
> + entry->state = tx_done;
> + dev_kfree_skb(tx_skb);
> +
> + return 1;
> +}
> +
> +static int
> +ax88796c_start_xmit(struct sk_buff *skb, struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + skb_queue_tail(&ax_local->tx_wait_q, skb);
> + if (skb_queue_len(&ax_local->tx_wait_q) > TX_QUEUE_HIGH_WATER) {
> + netif_err(ax_local, tx_queued, ndev,
> + "Too much TX packets in queue %d\n",
> + skb_queue_len(&ax_local->tx_wait_q));
> +
> + netif_stop_queue(ndev);
> + }
> +
> + set_bit(EVENT_TX, &ax_local->flags);
> + queue_work(ax_local->ax_work_queue, &ax_local->ax_work);
> +
> + return NETDEV_TX_OK;
> +}
> +
> +static void
> +ax88796c_skb_return(struct ax88796c_device *ax_local, struct sk_buff *skb,
> + struct rx_header *rxhdr)
> +{
> + struct net_device *ndev = ax_local->ndev;
> + int status;
> +
> + do {
> + if (!(ndev->features & NETIF_F_RXCSUM))
> + break;
> +
> + /* checksum error bit is set */
> + if ((rxhdr->flags & RX_HDR3_L3_ERR) ||
> + (rxhdr->flags & RX_HDR3_L4_ERR))
> + break;
> +
> + /* Other types may be indicated by more than one bit. */
> + if ((rxhdr->flags & RX_HDR3_L4_TYPE_TCP) ||
> + (rxhdr->flags & RX_HDR3_L4_TYPE_UDP))
> + skb->ip_summed = CHECKSUM_UNNECESSARY;
> + } while (0);
Why this do {} while(0) construct? If you want to separate this code,
then put it into its own function.
> +
> + ax_local->stats.rx_packets++;
> + ax_local->stats.rx_bytes += skb->len;
> + skb->dev = ndev;
> +
> + skb->truesize = skb->len + sizeof(struct sk_buff);
> + skb->protocol = eth_type_trans(skb, ax_local->ndev);
> +
> + netif_info(ax_local, rx_status, ndev, "< rx, len %zu, type 0x%x\n",
> + skb->len + sizeof(struct ethhdr), skb->protocol);
> +
> + status = netif_rx(skb);
> + if (status != NET_RX_SUCCESS)
> + netif_info(ax_local, rx_err, ndev,
> + "netif_rx status %d\n", status);
> +}
> +
> +static void
> +ax88796c_rx_fixup(struct ax88796c_device *ax_local, struct sk_buff *rx_skb)
> +{
> + struct rx_header *rxhdr = (struct rx_header *)rx_skb->data;
> + struct net_device *ndev = ax_local->ndev;
> + u16 len;
> +
> + be16_to_cpus(&rxhdr->flags_len);
> + be16_to_cpus(&rxhdr->seq_lenbar);
> + be16_to_cpus(&rxhdr->flags);
> +
> + if ((((short)rxhdr->flags_len) & RX_HDR1_PKT_LEN) !=
> + (~((short)rxhdr->seq_lenbar) & 0x7FF)) {
> + netif_err(ax_local, rx_err, ndev, "Header error\n");
> +
> + ax_local->stats.rx_frame_errors++;
> + kfree_skb(rx_skb);
> + return;
> + }
> +
> + if ((rxhdr->flags_len & RX_HDR1_MII_ERR) ||
> + (rxhdr->flags_len & RX_HDR1_CRC_ERR)) {
> + netif_err(ax_local, rx_err, ndev, "CRC or MII error\n");
> +
> + ax_local->stats.rx_crc_errors++;
> + kfree_skb(rx_skb);
> + return;
> + }
> +
> + len = rxhdr->flags_len & RX_HDR1_PKT_LEN;
> + if (netif_msg_pktdata(ax_local)) {
> + char pfx[IFNAMSIZ + 7];
> +
> + snprintf(pfx, sizeof(pfx), "%s: ", ndev->name);
> + netdev_info(ndev, "RX data, total len %d, packet len %d\n",
> + rx_skb->len, len);
> +
> + netdev_info(ndev, " Dump RX packet header:");
> + print_hex_dump(KERN_INFO, pfx, DUMP_PREFIX_OFFSET, 16, 1,
> + rx_skb->data, sizeof(*rxhdr), 0);
> +
> + netdev_info(ndev, " Dump RX packet:");
> + print_hex_dump(KERN_INFO, pfx, DUMP_PREFIX_OFFSET, 16, 1,
> + rx_skb->data + sizeof(*rxhdr), len, 0);
> + }
> +
> + skb_pull(rx_skb, sizeof(*rxhdr));
> + __pskb_trim(rx_skb, len);
> +
> + return ax88796c_skb_return(ax_local, rx_skb, rxhdr);
> +}
> +
> +static int ax88796c_receive(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + struct sk_buff *skb;
> + struct skb_data *entry;
> + u16 w_count, pkt_len;
> + u8 pkt_cnt;
> +
> + /* check rx packet and total word count */
> + AX_WRITE(&ax_local->ax_spi, AX_READ(&ax_local->ax_spi, P0_RTWCR)
> + | RTWCR_RX_LATCH, P0_RTWCR);
> +
> + pkt_cnt = AX_READ(&ax_local->ax_spi, P0_RXBCR2) & RXBCR2_PKT_MASK;
> + if (!pkt_cnt)
> + return 0;
> +
> + pkt_len = AX_READ(&ax_local->ax_spi, P0_RCPHR) & 0x7FF;
> +
> + w_count = ((pkt_len + 6 + 3) & 0xFFFC) >> 1;
> +
> + skb = alloc_skb((w_count * 2), GFP_KERNEL);
Also here, sure you don't have to use GFP_ATOMIC?
> + if (!skb) {
> + AX_WRITE(&ax_local->ax_spi, RXBCR1_RXB_DISCARD, P0_RXBCR1);
> + return 0;
> + }
> + entry = (struct skb_data *)skb->cb;
> +
> + AX_WRITE(&ax_local->ax_spi, RXBCR1_RXB_START | w_count, P0_RXBCR1);
> +
> + axspi_read_rxq(&ax_local->ax_spi,
> + skb_put(skb, w_count * 2), skb->len);
> +
> + /* Check if rx bridge is idle */
> + if ((AX_READ(&ax_local->ax_spi, P0_RXBCR2) & RXBCR2_RXB_IDLE) == 0) {
> + netif_err(ax_local, rx_err, ndev,
> + "Rx Bridge is not idle\n");
> + AX_WRITE(&ax_local->ax_spi, RXBCR2_RXB_REINIT, P0_RXBCR2);
> +
> + entry->state = rx_err;
> + } else {
> + entry->state = rx_done;
> + }
> +
> + AX_WRITE(&ax_local->ax_spi, ISR_RXPKT, P0_ISR);
> +
> + ax88796c_rx_fixup(ax_local, skb);
> +
> + return 1;
> +}
> +
> +static int ax88796c_process_isr(struct ax88796c_device *ax_local)
> +{
> + u16 isr;
> + u8 done = 0;
> + struct net_device *ndev = ax_local->ndev;
> +
> + isr = AX_READ(&ax_local->ax_spi, P0_ISR);
> + AX_WRITE(&ax_local->ax_spi, isr, P0_ISR);
> +
> + netif_dbg(ax_local, intr, ndev, " ISR 0x%04x\n", isr);
> +
> + if (isr & ISR_TXERR) {
> + netif_dbg(ax_local, intr, ndev, " TXERR interrupt\n");
> + AX_WRITE(&ax_local->ax_spi, TXNR_TXB_REINIT, P0_TSNR);
> + ax_local->seq_num = 0x1f;
> + }
> +
> + if (isr & ISR_TXPAGES) {
> + netif_dbg(ax_local, intr, ndev, " TXPAGES interrupt\n");
> + set_bit(EVENT_TX, &ax_local->flags);
> + }
> +
> + if (isr & ISR_LINK) {
> + netif_dbg(ax_local, intr, ndev, " Link change interrupt\n");
> + phy_mac_interrupt(ax_local->ndev->phydev);
> + }
> +
> + if (isr & ISR_RXPKT) {
> + netif_dbg(ax_local, intr, ndev, " RX interrupt\n");
> + done = ax88796c_receive(ax_local->ndev);
> + }
> +
> + return done;
> +}
> +
> +static irqreturn_t ax88796c_interrupt(int irq, void *dev_instance)
> +{
> + struct net_device *ndev = dev_instance;
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + if (!ndev) {
> + pr_err("irq %d for unknown device.\n", irq);
> + return IRQ_RETVAL(0);
> + }
> +
> + disable_irq_nosync(irq);
> +
> + netif_dbg(ax_local, intr, ndev, "Interrupt occurred\n");
> +
> + set_bit(EVENT_INTR, &ax_local->flags);
> + queue_work(ax_local->ax_work_queue, &ax_local->ax_work);
> +
Why not simpy using a threaded interrupt?
And in general: Why don't you use NAPI in the driver?
> + return IRQ_HANDLED;
> +}
> +
> +static void ax88796c_work(struct work_struct *work)
> +{
> + struct ax88796c_device *ax_local =
> + container_of(work, struct ax88796c_device, ax_work);
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + if (test_bit(EVENT_SET_MULTI, &ax_local->flags)) {
> + ax88796c_set_hw_multicast(ax_local->ndev);
> + clear_bit(EVENT_SET_MULTI, &ax_local->flags);
> + }
> +
> + if (test_bit(EVENT_INTR, &ax_local->flags)) {
> + AX_WRITE(&ax_local->ax_spi, IMR_MASKALL, P0_IMR);
> +
> + while (1) {
> + if (!ax88796c_process_isr(ax_local))
> + break;
> + }
> +
> + clear_bit(EVENT_INTR, &ax_local->flags);
> +
> + AX_WRITE(&ax_local->ax_spi, IMR_DEFAULT, P0_IMR);
> +
> + enable_irq(ax_local->ndev->irq);
> + }
> +
> + if (test_bit(EVENT_TX, &ax_local->flags)) {
> + while (skb_queue_len(&ax_local->tx_wait_q)) {
> + if (!ax88796c_hard_xmit(ax_local))
> + break;
> + }
> +
> + clear_bit(EVENT_TX, &ax_local->flags);
> +
> + if (netif_queue_stopped(ax_local->ndev) &&
> + (skb_queue_len(&ax_local->tx_wait_q) < TX_QUEUE_LOW_WATER))
> + netif_wake_queue(ax_local->ndev);
> + }
> +
> + mutex_unlock(&ax_local->spi_lock);
> +}
> +
> +static struct net_device_stats *ax88796c_get_stats(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + return &ax_local->stats;
> +}
> +
> +static void ax88796c_handle_link_change(struct net_device *ndev)
> +{
> + if (net_ratelimit())
> + phy_print_status(ndev->phydev);
> +}
> +
> +void ax88796c_phy_init(struct ax88796c_device *ax_local)
> +{
> + /* Enable PHY auto-polling */
> + AX_WRITE(&ax_local->ax_spi,
> + PCR_PHYID(0x10) | PCR_POLL_EN |
> + PCR_POLL_FLOWCTRL | PCR_POLL_BMCR, P2_PCR);
> +}
> +
> +static int
> +ax88796c_open(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + int ret;
> + unsigned long irq_flag = IRQF_SHARED;
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + ret = ax88796c_soft_reset(ax_local);
> + if (ret < 0)
> + return -ENODEV;
> +
> + ret = request_irq(ndev->irq, ax88796c_interrupt,
> + irq_flag, ndev->name, ndev);
> + if (ret) {
> + netdev_err(ndev, "unable to get IRQ %d (errno=%d).\n",
> + ndev->irq, ret);
> + return -ENXIO;
> + }
> +
> + ax_local->seq_num = 0x1f;
> +
> + ax88796c_set_mac_addr(ndev);
> + ax88796c_set_csums(ax_local);
> +
> + /* Disable stuffing packet */
> + AX_WRITE(&ax_local->ax_spi,
> + AX_READ(&ax_local->ax_spi, P1_RXBSPCR)
> + & ~RXBSPCR_STUF_ENABLE, P1_RXBSPCR);
> +
> + /* Enable RX packet process */
> + AX_WRITE(&ax_local->ax_spi, RPPER_RXEN, P1_RPPER);
> +
> + AX_WRITE(&ax_local->ax_spi, AX_READ(&ax_local->ax_spi, P0_FER)
> + | FER_RXEN | FER_TXEN | FER_BSWAP | FER_IRQ_PULL, P0_FER);
> +
> + /* Setup LED mode */
> + AX_WRITE(&ax_local->ax_spi,
> + (LCR_LED0_EN | LCR_LED0_DUPLEX | LCR_LED1_EN |
> + LCR_LED1_100MODE), P2_LCR0);
> + AX_WRITE(&ax_local->ax_spi,
> + (AX_READ(&ax_local->ax_spi, P2_LCR1) & LCR_LED2_MASK) |
> + LCR_LED2_EN | LCR_LED2_LINK, P2_LCR1);
> +
> + ax88796c_phy_init(ax_local);
> +
> + phy_start(ax_local->ndev->phydev);
> +
> + netif_start_queue(ndev);
> +
> + AX_WRITE(&ax_local->ax_spi, IMR_DEFAULT, P0_IMR);
> +
> + spi_message_init(&ax_local->ax_spi.rx_msg);
> +
> + mutex_unlock(&ax_local->spi_lock);
> +
> + return 0;
> +}
> +
> +static void ax88796c_free_skb_queue(struct sk_buff_head *q)
> +{
> + struct sk_buff *skb;
> +
> + while (q->qlen) {
> + skb = skb_dequeue(q);
> + kfree_skb(skb);
> + }
> +}
> +
> +static int
> +ax88796c_close(struct net_device *ndev)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> +
> + netif_stop_queue(ndev);
> +
> + free_irq(ndev->irq, ndev);
This looks racy. I think e.g. you can still get e.g. rx interrupts.
> +
> + phy_stop(ndev->phydev);
> +
> + mutex_lock(&ax_local->spi_lock);
> +
> + AX_WRITE(&ax_local->ax_spi, IMR_MASKALL, P0_IMR);
> + ax88796c_free_skb_queue(&ax_local->tx_wait_q);
> +
> + ax88796c_soft_reset(ax_local);
> +
> + mutex_unlock(&ax_local->spi_lock);
> + netif_carrier_off(ndev);
> +
> + return 0;
> +}
> +
> +static int
> +ax88796c_set_features(struct net_device *ndev, netdev_features_t features)
> +{
> + struct ax88796c_device *ax_local = to_ax88796c_device(ndev);
> + netdev_features_t changed = features ^ ndev->features;
> +
> + if (!(changed & (NETIF_F_RXCSUM | NETIF_F_HW_CSUM)))
> + return 0;
> +
> + ndev->features = features;
> +
> + if (changed & (NETIF_F_RXCSUM | NETIF_F_HW_CSUM))
> + ax88796c_set_csums(ax_local);
> +
> + return 0;
> +}
> +
> +static const struct net_device_ops ax88796c_netdev_ops = {
> + .ndo_open = ax88796c_open,
> + .ndo_stop = ax88796c_close,
> + .ndo_start_xmit = ax88796c_start_xmit,
> + .ndo_get_stats = ax88796c_get_stats,
> + .ndo_do_ioctl = ax88796c_ioctl,
> + .ndo_set_mac_address = ax88796c_set_mac_address,
> + .ndo_set_features = ax88796c_set_features,
> +};
> +
> +static int ax88796c_hard_reset(struct ax88796c_device *ax_local)
> +{
> + struct device *dev = (struct device *)&ax_local->spi->dev;
> + struct gpio_desc *reset_gpio;
> +
> + /* reset info */
> + reset_gpio = gpiod_get(dev, "reset", 0);
> + if (IS_ERR(reset_gpio)) {
> + dev_err(dev, "Could not get 'reset' GPIO: %ld", PTR_ERR(reset_gpio));
> + return PTR_ERR(reset_gpio);
> + }
> +
> + /* set reset */
> + gpiod_direction_output(reset_gpio, 1);
> + msleep(100);
> + gpiod_direction_output(reset_gpio, 0);
> + gpiod_put(reset_gpio);
> + msleep(20);
> +
> + return 0;
> +}
> +
> +static int ax88796c_probe(struct spi_device *spi)
> +{
> + struct net_device *ndev;
> + struct ax88796c_device *ax_local;
> + int ret;
> + u16 temp;
> +
> + ndev = devm_alloc_etherdev(&spi->dev, sizeof(*ax_local));
> + if (!ndev) {
> + dev_err(&spi->dev, "AX88796C SPI: Could not allocate ethernet device\n");
> + return -ENOMEM;
> + }
> + SET_NETDEV_DEV(ndev, &spi->dev);
> +
> + ax_local = to_ax88796c_device(ndev);
> + memset(ax_local, 0, sizeof(*ax_local));
> +
> + dev_set_drvdata(&spi->dev, ax_local);
> + ax_local->spi = spi;
> + ax_local->ax_spi.spi = spi;
> +
> + ax_local->ndev = ndev;
> + ax_local->capabilities |= comp ? AX_CAP_COMP : 0;
> + ax_local->msg_enable = msg_enable;
> +
> + ax_local->mdiobus = devm_mdiobus_alloc(&spi->dev);
> + if (!ax_local->mdiobus) {
> + dev_err(&spi->dev, "Could not allocate MDIO bus\n");
> + return -ENOMEM;
> + }
> +
> + ax_local->mdiobus->priv = ax_local;
> + ax_local->mdiobus->read = ax88796c_mdio_read;
> + ax_local->mdiobus->write = ax88796c_mdio_write;
> + ax_local->mdiobus->name = "ax88976c-mdiobus";
> + ax_local->mdiobus->phy_mask = ~(1 << 0x10);
> + ax_local->mdiobus->parent = &spi->dev;
> +
> + snprintf(ax_local->mdiobus->id, ARRAY_SIZE(ax_local->mdiobus->id),
> + "ax88796c-spi-%s.%u", dev_name(&spi->dev), spi->chip_select);
> +
> + ret = devm_mdiobus_register(&spi->dev, ax_local->mdiobus);
> + if (ret < 0) {
> + dev_err(&spi->dev, "Could not register MDIO bus\n");
> + return ret;
> + }
> +
> + if (netif_msg_probe(ax_local)) {
> + dev_info(&spi->dev, "AX88796C-SPI Configuration:\n");
> + dev_info(&spi->dev, " Compression : %s\n",
> + ax_local->capabilities & AX_CAP_COMP ? "ON" : "OFF");
> + }
> +
> + ndev->irq = spi->irq;
> + ndev->netdev_ops = &ax88796c_netdev_ops;
> + ndev->ethtool_ops = &ax88796c_ethtool_ops;
> + ndev->hw_features |= NETIF_F_HW_CSUM | NETIF_F_RXCSUM;
> + ndev->features |= NETIF_F_HW_CSUM | NETIF_F_RXCSUM;
> + ndev->hard_header_len += (TX_OVERHEAD + 4);
> +
> + /* ax88796c gpio reset */
> + ax88796c_hard_reset(ax_local);
> +
> + /* Reset AX88796C */
> + ret = ax88796c_soft_reset(ax_local);
> + if (ret < 0) {
> + ret = -ENODEV;
> + goto err;
> + }
> + /* Check board revision */
> + temp = AX_READ(&ax_local->ax_spi, P2_CRIR);
> + if ((temp & 0xF) != 0x0) {
> + dev_err(&spi->dev, "spi read failed: %d\n", temp);
> + ret = -ENODEV;
> + goto err;
> + }
> +
> + temp = AX_READ(&ax_local->ax_spi, P0_BOR);
> + if (temp == 0x1234) {
> + ax_local->plat_endian = PLAT_LITTLE_ENDIAN;
> + } else {
> + AX_WRITE(&ax_local->ax_spi, 0xFFFF, P0_BOR);
> + ax_local->plat_endian = PLAT_BIG_ENDIAN;
> + }
> +
> + /*Reload EEPROM*/
> + ax88796c_reload_eeprom(ax_local);
> +
> + ax88796c_load_mac_addr(ndev);
> +
> + if (netif_msg_probe(ax_local))
> + dev_info(&spi->dev,
> + "irq %d, MAC addr %02X:%02X:%02X:%02X:%02X:%02X\n",
> + ndev->irq,
> + ndev->dev_addr[0], ndev->dev_addr[1],
> + ndev->dev_addr[2], ndev->dev_addr[3],
> + ndev->dev_addr[4], ndev->dev_addr[5]);
> +
> + /* Disable power saving */
> + AX_WRITE(&ax_local->ax_spi, (AX_READ(&ax_local->ax_spi, P0_PSCR)
> + & PSCR_PS_MASK) | PSCR_PS_D0, P0_PSCR);
> +
> + INIT_WORK(&ax_local->ax_work, ax88796c_work);
> +
> + ax_local->ax_work_queue =
> + create_singlethread_workqueue("ax88796c_work");
> +
> + mutex_init(&ax_local->spi_lock);
> +
> + skb_queue_head_init(&ax_local->tx_wait_q);
> +
> + ret = devm_register_netdev(&spi->dev, ndev);
> + if (ret) {
> + dev_err(&spi->dev, "failed to register a network device\n");
> + destroy_workqueue(ax_local->ax_work_queue);
> + goto err;
> + }
> +
> + ax_local->phydev = phy_find_first(ax_local->mdiobus);
> + if (!ax_local->phydev) {
> + dev_err(&spi->dev, "no PHY found\n");
> + ret = -ENODEV;
> + goto err;
> + }
> +
> + ax_local->phydev->irq = PHY_IGNORE_INTERRUPT;
> + phy_connect_direct(ax_local->ndev, ax_local->phydev,
> + ax88796c_handle_link_change,
> + PHY_INTERFACE_MODE_MII);
> +
> + netif_info(ax_local, probe, ndev, "%s %s registered\n",
> + dev_driver_string(&spi->dev),
> + dev_name(&spi->dev));
> + phy_attached_info(ax_local->phydev);
Does the integrated PHY provide a proper PHY ID?
Is there a PHY driver for it or do you rely on the genphy driver?
> +
> + ret = 0;
> +err:
> + return ret;
> +}
> +
> +static int ax88796c_remove(struct spi_device *spi)
> +{
> + struct ax88796c_device *ax_local = dev_get_drvdata(&spi->dev);
> + struct net_device *ndev = ax_local->ndev;
> +
> + netif_info(ax_local, probe, ndev, "removing network device %s %s\n",
> + dev_driver_string(&spi->dev),
> + dev_name(&spi->dev));
> +
> + destroy_workqueue(ax_local->ax_work_queue);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ax88796c_dt_ids[] = {
> + { .compatible = "asix,ax88796c" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ax88796c_dt_ids);
> +
> +static const struct spi_device_id asix_id[] = {
> + { "ax88796c", 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(spi, asix_id);
> +
> +static struct spi_driver ax88796c_spi_driver = {
> + .driver = {
> + .name = DRV_NAME,
> +#ifdef CONFIG_USE_OF
> + .of_match_table = of_match_ptr(ax88796c_dt_ids),
> +#endif
> + },
> + .probe = ax88796c_probe,
> + .remove = ax88796c_remove,
> + .id_table = asix_id,
> +};
> +
> +static __init int ax88796c_spi_init(void)
> +{
> + int ret;
> +
> + bitmap_zero(ax88796c_no_regs_mask, AX88796C_REGDUMP_LEN);
> + ret = bitmap_parse(no_regs_list, 35,
> + ax88796c_no_regs_mask, AX88796C_REGDUMP_LEN);
> + if (ret) {
> + bitmap_fill(ax88796c_no_regs_mask, AX88796C_REGDUMP_LEN);
> + pr_err("Invalid bitmap description, masking all registers\n");
> + }
> +
> + return spi_register_driver(&ax88796c_spi_driver);
> +}
> +
> +static __exit void ax88796c_spi_exit(void)
> +{
> + spi_unregister_driver(&ax88796c_spi_driver);
> +}
> +
> +module_init(ax88796c_spi_init);
> +module_exit(ax88796c_spi_exit);
> +
> +MODULE_AUTHOR("ASIX");
> +MODULE_DESCRIPTION("ASIX AX88796C SPI Ethernet driver");
> +MODULE_LICENSE("GPL");
> +
> +/* ax88796c_phy */
> diff --git a/drivers/net/ethernet/asix/ax88796c_main.h b/drivers/net/ethernet/asix/ax88796c_main.h
> new file mode 100644
> index 000000000000..428833978fbf
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/ax88796c_main.h
> @@ -0,0 +1,568 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * Copyright (c) 2010 ASIX Electronics Corporation
> + * Copyright (c) 2020 Samsung Electronics
> + *
> + * ASIX AX88796C SPI Fast Ethernet Linux driver
> + */
> +
> +#ifndef _AX88796C_MAIN_H
> +#define _AX88796C_MAIN_H
> +
> +#include <linux/netdevice.h>
> +#include <linux/mii.h>
> +
> +#include "ax88796c_spi.h"
> +
> +/* These identify the driver base version and may not be removed. */
> +#define DRV_NAME "ax88796c"
> +#define ADP_NAME "ASIX AX88796C SPI Ethernet Adapter"
> +#define DRV_VERSION "1.2.0"
> +
An benefit in using a separate driver version? Typically the
kernel version is sufficient.
> +#define TX_QUEUE_HIGH_WATER 45 /* Tx queue high water mark */
> +#define TX_QUEUE_LOW_WATER 20 /* Tx queue low water mark */
> +
> +#define AX88796C_REGDUMP_LEN 256
> +#define AX88796C_PHY_REGDUMP_LEN 12
> +
> +#define TX_OVERHEAD 8
> +#define TX_EOP_SIZE 4
> +
> +#define AX_MCAST_FILTER_SIZE 8
> +#define AX_MAX_MCAST 64
> +#define AX_MAX_CLK 80000000
> +#define TX_HDR_SOP_DICF 0x8000
> +#define TX_HDR_SOP_CPHI 0x4000
> +#define TX_HDR_SOP_INT 0x2000
> +#define TX_HDR_SOP_MDEQ 0x1000
> +#define TX_HDR_SOP_PKTLEN 0x07FF
> +#define TX_HDR_SOP_SEQNUM 0xF800
> +#define TX_HDR_SOP_PKTLENBAR 0x07FF
> +
> +#define TX_HDR_SEG_FS 0x8000
> +#define TX_HDR_SEG_LS 0x4000
> +#define TX_HDR_SEG_SEGNUM 0x3800
> +#define TX_HDR_SEG_SEGLEN 0x0700
> +#define TX_HDR_SEG_EOFST 0xC000
> +#define TX_HDR_SEG_SOFST 0x3800
> +#define TX_HDR_SEG_SEGLENBAR 0x07FF
> +
> +#define TX_HDR_EOP_SEQNUM 0xF800
> +#define TX_HDR_EOP_PKTLEN 0x07FF
> +#define TX_HDR_EOP_SEQNUMBAR 0xF800
> +#define TX_HDR_EOP_PKTLENBAR 0x07FF
> +
> +/* Rx header fields mask */
> +#define RX_HDR1_MCBC 0x8000
> +#define RX_HDR1_STUFF_PKT 0x4000
> +#define RX_HDR1_MII_ERR 0x2000
> +#define RX_HDR1_CRC_ERR 0x1000
> +#define RX_HDR1_PKT_LEN 0x07FF
> +
> +#define RX_HDR2_SEQ_NUM 0xF800
> +#define RX_HDR2_PKT_LEN_BAR 0x7FFF
> +
> +#define RX_HDR3_PE 0x8000
> +#define RX_HDR3_L3_TYPE_IPV4V6 0x6000
> +#define RX_HDR3_L3_TYPE_IP 0x4000
> +#define RX_HDR3_L3_TYPE_IPV6 0x2000
> +#define RX_HDR3_L4_TYPE_ICMPV6 0x1400
> +#define RX_HDR3_L4_TYPE_TCP 0x1000
> +#define RX_HDR3_L4_TYPE_IGMP 0x0c00
> +#define RX_HDR3_L4_TYPE_ICMP 0x0800
> +#define RX_HDR3_L4_TYPE_UDP 0x0400
> +#define RX_HDR3_L3_ERR 0x0200
> +#define RX_HDR3_L4_ERR 0x0100
> +#define RX_HDR3_PRIORITY(x) ((x) << 4)
> +#define RX_HDR3_STRIP 0x0008
> +#define RX_HDR3_VLAN_ID 0x0007
> +
> +enum watchdog_state {
> + chk_link = 0,
> + chk_cable,
> + ax_nop,
> +};
> +
> +struct ax88796c_device {
> + struct resource *addr_res; /* resources found */
> + struct resource *addr_req; /* resources requested */
> + struct resource *irq_res;
> +
> + struct spi_device *spi;
> + struct net_device *ndev;
> + struct net_device_stats stats;
> +
> + struct timer_list watchdog;
> + enum watchdog_state w_state;
> + size_t w_ticks;
> +
> + struct work_struct ax_work;
> + struct workqueue_struct *ax_work_queue;
> + struct tasklet_struct bh;
> +
> + struct mutex spi_lock; /* device access */
> +
> + struct sk_buff_head tx_wait_q;
> +
> + struct axspi_data ax_spi;
> +
> + struct mii_bus *mdiobus;
> + struct phy_device *phydev;
> +
> + int msg_enable;
> +
> + u16 seq_num;
> +
> + u8 multi_filter[AX_MCAST_FILTER_SIZE];
> +
> + unsigned long capabilities;
> + #define AX_CAP_DMA 1
> + #define AX_CAP_COMP 2
> + #define AX_CAP_BIDIR 4
> +
> + u8 plat_endian;
> + #define PLAT_LITTLE_ENDIAN 0
> + #define PLAT_BIG_ENDIAN 1
> +
> + unsigned long flags;
> + #define EVENT_INTR 1
> + #define EVENT_TX 2
> + #define EVENT_SET_MULTI 4
> +
> +};
> +
> +#define to_ax88796c_device(ndev) ((struct ax88796c_device *)netdev_priv(ndev))
> +
Is this helper really needed? in The places I've seen you can assign
the void* pointer returned netdev_priv().
> +enum skb_state {
> + illegal = 0,
> + tx_done,
> + rx_done,
> + rx_err,
> +};
> +
> +struct skb_data;
> +
> +struct skb_data {
> + enum skb_state state;
> + struct net_device *ndev;
> + struct sk_buff *skb;
> + size_t len;
> + dma_addr_t phy_addr;
> +};
> +
> +/* A88796C register definition */
> + /* Definition of PAGE0 */
> +#define P0_PSR (0x00)
> + #define PSR_DEV_READY (1 << 7)
> + #define PSR_RESET (0 << 15)
> + #define PSR_RESET_CLR (1 << 15)
> +#define P0_BOR (0x02)
> +#define P0_FER (0x04)
> + #define FER_IPALM (1 << 0)
> + #define FER_DCRC (1 << 1)
> + #define FER_RH3M (1 << 2)
> + #define FER_HEADERSWAP (1 << 7)
> + #define FER_WSWAP (1 << 8)
> + #define FER_BSWAP (1 << 9)
> + #define FER_INTHI (1 << 10)
> + #define FER_INTLO (0 << 10)
> + #define FER_IRQ_PULL (1 << 11)
> + #define FER_RXEN (1 << 14)
> + #define FER_TXEN (1 << 15)
> +#define P0_ISR (0x06)
> + #define ISR_RXPKT (1 << 0)
> + #define ISR_MDQ (1 << 4)
> + #define ISR_TXT (1 << 5)
> + #define ISR_TXPAGES (1 << 6)
> + #define ISR_TXERR (1 << 8)
> + #define ISR_LINK (1 << 9)
> +#define P0_IMR (0x08)
> + #define IMR_RXPKT (1 << 0)
> + #define IMR_MDQ (1 << 4)
> + #define IMR_TXT (1 << 5)
> + #define IMR_TXPAGES (1 << 6)
> + #define IMR_TXERR (1 << 8)
> + #define IMR_LINK (1 << 9)
> + #define IMR_MASKALL (0xFFFF)
> + #define IMR_DEFAULT (IMR_TXERR)
> +#define P0_WFCR (0x0A)
> + #define WFCR_PMEIND (1 << 0) /* PME indication */
> + #define WFCR_PMETYPE (1 << 1) /* PME I/O type */
> + #define WFCR_PMEPOL (1 << 2) /* PME polarity */
> + #define WFCR_PMERST (1 << 3) /* Reset PME */
> + #define WFCR_SLEEP (1 << 4) /* Enable sleep mode */
> + #define WFCR_WAKEUP (1 << 5) /* Enable wakeup mode */
> + #define WFCR_WAITEVENT (1 << 6) /* Reserved */
> + #define WFCR_CLRWAKE (1 << 7) /* Clear wakeup */
> + #define WFCR_LINKCH (1 << 8) /* Enable link change */
> + #define WFCR_MAGICP (1 << 9) /* Enable magic packet */
> + #define WFCR_WAKEF (1 << 10) /* Enable wakeup frame */
> + #define WFCR_PMEEN (1 << 11) /* Enable PME pin */
> + #define WFCR_LINKCHS (1 << 12) /* Link change status */
> + #define WFCR_MAGICPS (1 << 13) /* Magic packet status */
> + #define WFCR_WAKEFS (1 << 14) /* Wakeup frame status */
> + #define WFCR_PMES (1 << 15) /* PME pin status */
> +#define P0_PSCR (0x0C)
> + #define PSCR_PS_MASK (0xFFF0)
> + #define PSCR_PS_D0 (0)
> + #define PSCR_PS_D1 (1 << 0)
> + #define PSCR_PS_D2 (1 << 1)
> + #define PSCR_FPS (1 << 3) /* Enable fiber mode PS */
> + #define PSCR_SWPS (1 << 4) /* Enable software */
> + /* PS control */
> + #define PSCR_WOLPS (1 << 5) /* Enable WOL PS */
> + #define PSCR_SWWOL (1 << 6) /* Enable software select */
> + /* WOL PS */
> + #define PSCR_PHYOSC (1 << 7) /* Internal PHY OSC control */
> + #define PSCR_FOFEF (1 << 8) /* Force PHY generate FEF */
> + #define PSCR_FOF (1 << 9) /* Force PHY in fiber mode */
> + #define PSCR_PHYPD (1 << 10) /* PHY power down. */
> + /* Active high */
> + #define PSCR_PHYRST (1 << 11) /* PHY reset signal. */
> + /* Active low */
> + #define PSCR_PHYCSIL (1 << 12) /* PHY cable energy detect */
> + #define PSCR_PHYCOFF (1 << 13) /* PHY cable off */
> + #define PSCR_PHYLINK (1 << 14) /* PHY link status */
> + #define PSCR_EEPOK (1 << 15) /* EEPROM load complete */
> +#define P0_MACCR (0x0E)
> + #define MACCR_RXFC_ENABLE (1 << 3)
> + #define MACCR_RXFC_MASK 0xFFF7
> + #define MACCR_TXFC_ENABLE (1 << 4)
> + #define MACCR_TXFC_MASK 0xFFEF
> + #define MACCR_PSI (1 << 6) /* Software Cable-Off */
> + /* Power Saving Interrupt */
> + #define MACCR_PF (1 << 7)
> + #define MACCR_PMM_BITS 8
> + #define MACCR_PMM_MASK (0x1F00)
> + #define MACCR_PMM_RESET (1 << 8)
> + #define MACCR_PMM_WAIT (2 << 8)
> + #define MACCR_PMM_READY (3 << 8)
> + #define MACCR_PMM_D1 (4 << 8)
> + #define MACCR_PMM_D2 (5 << 8)
> + #define MACCR_PMM_WAKE (7 << 8)
> + #define MACCR_PMM_D1_WAKE (8 << 8)
> + #define MACCR_PMM_D2_WAKE (9 << 8)
> + #define MACCR_PMM_SLEEP (10 << 8)
> + #define MACCR_PMM_PHY_RESET (11 << 8)
> + #define MACCR_PMM_SOFT_D1 (16 << 8)
> + #define MACCR_PMM_SOFT_D2 (17 << 8)
> +#define P0_TFBFCR (0x10)
> + #define TFBFCR_SCHE_FREE_PAGE 0xE07F
> + #define TFBFCR_FREE_PAGE_BITS 0x07
> + #define TFBFCR_FREE_PAGE_LATCH (1 << 6)
> + #define TFBFCR_SET_FREE_PAGE(x) (((x) & 0x3F) << TFBFCR_FREE_PAGE_BITS)
> + #define TFBFCR_TX_PAGE_SET (1 << 13)
> + #define TFBFCR_MANU_ENTX (1 << 15)
> + #define TX_FREEBUF_MASK 0x003F
> + #define TX_DPTSTART 0x4000
> +
> +#define P0_TSNR (0x12)
> + #define TXNR_TXB_ERR (1 << 5)
> + #define TXNR_TXB_IDLE (1 << 6)
> + #define TSNR_PKT_CNT(x) (((x) & 0x3F) << 8)
> + #define TXNR_TXB_REINIT (1 << 14)
> + #define TSNR_TXB_START (1 << 15)
> +#define P0_RTDPR (0x14)
> +#define P0_RXBCR1 (0x16)
> + #define RXBCR1_RXB_DISCARD (1 << 14)
> + #define RXBCR1_RXB_START (1 << 15)
> +#define P0_RXBCR2 (0x18)
> + #define RXBCR2_PKT_MASK (0xFF)
> + #define RXBCR2_RXPC_MASK (0x7F)
> + #define RXBCR2_RXB_READY (1 << 13)
> + #define RXBCR2_RXB_IDLE (1 << 14)
> + #define RXBCR2_RXB_REINIT (1 << 15)
> +#define P0_RTWCR (0x1A)
> + #define RTWCR_RXWC_MASK (0x3FFF)
> + #define RTWCR_RX_LATCH (1 << 15)
> +#define P0_RCPHR (0x1C)
> +
> + /* Definition of PAGE1 */
> +#define P1_RPPER (0x22)
> + #define RPPER_RXEN (1 << 0)
> +#define P1_MRCR (0x28)
> +#define P1_MDR (0x2A)
> +#define P1_RMPR (0x2C)
> +#define P1_TMPR (0x2E)
> +#define P1_RXBSPCR (0x30)
> + #define RXBSPCR_STUF_WORD_CNT(x) (((x) & 0x7000) >> 12)
> + #define RXBSPCR_STUF_ENABLE (1 << 15)
> +#define P1_MCR (0x32)
> + #define MCR_SBP (1 << 8)
> + #define MCR_SM (1 << 9)
> + #define MCR_CRCENLAN (1 << 11)
> + #define MCR_STP (1 << 12)
> + /* Definition of PAGE2 */
> +#define P2_CIR (0x42)
> +#define P2_PCR (0x44)
> + #define PCR_POLL_EN (1 << 0)
> + #define PCR_POLL_FLOWCTRL (1 << 1)
> + #define PCR_POLL_BMCR (1 << 2)
> + #define PCR_PHYID(x) ((x) << 8)
> +#define P2_PHYSR (0x46)
> +#define P2_MDIODR (0x48)
> +#define P2_MDIOCR (0x4A)
> + #define MDIOCR_RADDR(x) ((x) & 0x1F)
> + #define MDIOCR_FADDR(x) (((x) & 0x1F) << 8)
> + #define MDIOCR_VALID (1 << 13)
> + #define MDIOCR_READ (1 << 14)
> + #define MDIOCR_WRITE (1 << 15)
> +#define P2_LCR0 (0x4C)
> + #define LCR_LED0_EN (1 << 0)
> + #define LCR_LED0_100MODE (1 << 1)
> + #define LCR_LED0_DUPLEX (1 << 2)
> + #define LCR_LED0_LINK (1 << 3)
> + #define LCR_LED0_ACT (1 << 4)
> + #define LCR_LED0_COL (1 << 5)
> + #define LCR_LED0_10MODE (1 << 6)
> + #define LCR_LED0_DUPCOL (1 << 7)
> + #define LCR_LED1_EN (1 << 8)
> + #define LCR_LED1_100MODE (1 << 9)
> + #define LCR_LED1_DUPLEX (1 << 10)
> + #define LCR_LED1_LINK (1 << 11)
> + #define LCR_LED1_ACT (1 << 12)
> + #define LCR_LED1_COL (1 << 13)
> + #define LCR_LED1_10MODE (1 << 14)
> + #define LCR_LED1_DUPCOL (1 << 15)
> +#define P2_LCR1 (0x4E)
> + #define LCR_LED2_MASK (0xFF00)
> + #define LCR_LED2_EN (1 << 0)
> + #define LCR_LED2_100MODE (1 << 1)
> + #define LCR_LED2_DUPLEX (1 << 2)
> + #define LCR_LED2_LINK (1 << 3)
> + #define LCR_LED2_ACT (1 << 4)
> + #define LCR_LED2_COL (1 << 5)
> + #define LCR_LED2_10MODE (1 << 6)
> + #define LCR_LED2_DUPCOL (1 << 7)
> +#define P2_IPGCR (0x50)
> +#define P2_CRIR (0x52)
> +#define P2_FLHWCR (0x54)
> +#define P2_RXCR (0x56)
> + #define RXCR_PRO (1 << 0)
> + #define RXCR_AMALL (1 << 1)
> + #define RXCR_SEP (1 << 2)
> + #define RXCR_AB (1 << 3)
> + #define RXCR_AM (1 << 4)
> + #define RXCR_AP (1 << 5)
> + #define RXCR_ARP (1 << 6)
> +#define P2_JLCR (0x58)
> +#define P2_MPLR (0x5C)
> +
> + /* Definition of PAGE3 */
> +#define P3_MACASR0 (0x62)
> + #define P3_MACASR(x) (P3_MACASR0 + 2 * (x))
> + #define MACASR_LOWBYTE_MASK 0x00FF
> + #define MACASR_HIGH_BITS 0x08
> +#define P3_MACASR1 (0x64)
> +#define P3_MACASR2 (0x66)
> +#define P3_MFAR01 (0x68)
> +#define P3_MFAR_BASE (0x68)
> + #define P3_MFAR(x) (P3_MFAR_BASE + 2 * (x))
> +
> +#define P3_MFAR23 (0x6A)
> +#define P3_MFAR45 (0x6C)
> +#define P3_MFAR67 (0x6E)
> +#define P3_VID0FR (0x70)
> +#define P3_VID1FR (0x72)
> +#define P3_EECSR (0x74)
> +#define P3_EEDR (0x76)
> +#define P3_EECR (0x78)
> + #define EECR_ADDR_MASK (0x00FF)
> + #define EECR_READ_ACT (1 << 8)
> + #define EECR_WRITE_ACT (1 << 9)
> + #define EECR_WRITE_DISABLE (1 << 10)
> + #define EECR_WRITE_ENABLE (1 << 11)
> + #define EECR_EE_READY (1 << 13)
> + #define EECR_RELOAD (1 << 14)
> + #define EECR_RESET (1 << 15)
> +#define P3_TPCR (0x7A)
> + #define TPCR_PATT_MASK (0xFF)
> + #define TPCR_RAND_PKT_EN (1 << 14)
> + #define TPCR_FIXED_PKT_EN (1 << 15)
> +#define P3_TPLR (0x7C)
> + /* Definition of PAGE4 */
> +#define P4_SPICR (0x8A)
> + #define SPICR_RCEN (1 << 0)
> + #define SPICR_QCEN (1 << 1)
> + #define SPICR_RBRE (1 << 3)
> + #define SPICR_PMM (1 << 4)
> + #define SPICR_LOOPBACK (1 << 8)
> + #define SPICR_CORE_RES_CLR (1 << 10)
> + #define SPICR_SPI_RES_CLR (1 << 11)
> +#define P4_SPIISMR (0x8C)
> +
> +#define P4_COERCR0 (0x92)
> + #define COERCR0_RXIPCE (1 << 0)
> + #define COERCR0_RXIPVE (1 << 1)
> + #define COERCR0_RXV6PE (1 << 2)
> + #define COERCR0_RXTCPE (1 << 3)
> + #define COERCR0_RXUDPE (1 << 4)
> + #define COERCR0_RXICMP (1 << 5)
> + #define COERCR0_RXIGMP (1 << 6)
> + #define COERCR0_RXICV6 (1 << 7)
> +
> + #define COERCR0_RXTCPV6 (1 << 8)
> + #define COERCR0_RXUDPV6 (1 << 9)
> + #define COERCR0_RXICMV6 (1 << 10)
> + #define COERCR0_RXIGMV6 (1 << 11)
> + #define COERCR0_RXICV6V6 (1 << 12)
> +
> + #define COERCR0_DEFAULT (COERCR0_RXIPCE | COERCR0_RXV6PE | \
> + COERCR0_RXTCPE | COERCR0_RXUDPE | \
> + COERCR0_RXTCPV6 | COERCR0_RXUDPV6)
> +#define P4_COERCR1 (0x94)
> + #define COERCR1_IPCEDP (1 << 0)
> + #define COERCR1_IPVEDP (1 << 1)
> + #define COERCR1_V6VEDP (1 << 2)
> + #define COERCR1_TCPEDP (1 << 3)
> + #define COERCR1_UDPEDP (1 << 4)
> + #define COERCR1_ICMPDP (1 << 5)
> + #define COERCR1_IGMPDP (1 << 6)
> + #define COERCR1_ICV6DP (1 << 7)
> + #define COERCR1_RX64TE (1 << 8)
> + #define COERCR1_RXPPPE (1 << 9)
> + #define COERCR1_TCP6DP (1 << 10)
> + #define COERCR1_UDP6DP (1 << 11)
> + #define COERCR1_IC6DP (1 << 12)
> + #define COERCR1_IG6DP (1 << 13)
> + #define COERCR1_ICV66DP (1 << 14)
> + #define COERCR1_RPCE (1 << 15)
> +
> + #define COERCR1_DEFAULT (COERCR1_RXPPPE)
> +
> +#define P4_COETCR0 (0x96)
> + #define COETCR0_TXIP (1 << 0)
> + #define COETCR0_TXTCP (1 << 1)
> + #define COETCR0_TXUDP (1 << 2)
> + #define COETCR0_TXICMP (1 << 3)
> + #define COETCR0_TXIGMP (1 << 4)
> + #define COETCR0_TXICV6 (1 << 5)
> + #define COETCR0_TXTCPV6 (1 << 8)
> + #define COETCR0_TXUDPV6 (1 << 9)
> + #define COETCR0_TXICMV6 (1 << 10)
> + #define COETCR0_TXIGMV6 (1 << 11)
> + #define COETCR0_TXICV6V6 (1 << 12)
> +
> + #define COETCR0_DEFAULT (COETCR0_TXIP | COETCR0_TXTCP | \
> + COETCR0_TXUDP | COETCR0_TXTCPV6 | \
> + COETCR0_TXUDPV6)
> +#define P4_COETCR1 (0x98)
> + #define COETCR1_TX64TE (1 << 0)
> + #define COETCR1_TXPPPE (1 << 1)
> +
> +#define P4_COECEDR (0x9A)
> +#define P4_L2CECR (0x9C)
> +
> + /* Definition of PAGE5 */
> +#define P5_WFTR (0xA2)
> + #define WFTR_2MS (0x01)
> + #define WFTR_4MS (0x02)
> + #define WFTR_8MS (0x03)
> + #define WFTR_16MS (0x04)
> + #define WFTR_32MS (0x05)
> + #define WFTR_64MS (0x06)
> + #define WFTR_128MS (0x07)
> + #define WFTR_256MS (0x08)
> + #define WFTR_512MS (0x09)
> + #define WFTR_1024MS (0x0A)
> + #define WFTR_2048MS (0x0B)
> + #define WFTR_4096MS (0x0C)
> + #define WFTR_8192MS (0x0D)
> + #define WFTR_16384MS (0x0E)
> + #define WFTR_32768MS (0x0F)
> +#define P5_WFCCR (0xA4)
> +#define P5_WFCR03 (0xA6)
> + #define WFCR03_F0_EN (1 << 0)
> + #define WFCR03_F1_EN (1 << 4)
> + #define WFCR03_F2_EN (1 << 8)
> + #define WFCR03_F3_EN (1 << 12)
> +#define P5_WFCR47 (0xA8)
> + #define WFCR47_F4_EN (1 << 0)
> + #define WFCR47_F5_EN (1 << 4)
> + #define WFCR47_F6_EN (1 << 8)
> + #define WFCR47_F7_EN (1 << 12)
> +#define P5_WF0BMR0 (0xAA)
> +#define P5_WF0BMR1 (0xAC)
> +#define P5_WF0CR (0xAE)
> +#define P5_WF0OBR (0xB0)
> +#define P5_WF1BMR0 (0xB2)
> +#define P5_WF1BMR1 (0xB4)
> +#define P5_WF1CR (0xB6)
> +#define P5_WF1OBR (0xB8)
> +#define P5_WF2BMR0 (0xBA)
> +#define P5_WF2BMR1 (0xBC)
> +
> + /* Definition of PAGE6 */
> +#define P6_WF2CR (0xC2)
> +#define P6_WF2OBR (0xC4)
> +#define P6_WF3BMR0 (0xC6)
> +#define P6_WF3BMR1 (0xC8)
> +#define P6_WF3CR (0xCA)
> +#define P6_WF3OBR (0xCC)
> +#define P6_WF4BMR0 (0xCE)
> +#define P6_WF4BMR1 (0xD0)
> +#define P6_WF4CR (0xD2)
> +#define P6_WF4OBR (0xD4)
> +#define P6_WF5BMR0 (0xD6)
> +#define P6_WF5BMR1 (0xD8)
> +#define P6_WF5CR (0xDA)
> +#define P6_WF5OBR (0xDC)
> +
> +/* Definition of PAGE7 */
> +#define P7_WF6BMR0 (0xE2)
> +#define P7_WF6BMR1 (0xE4)
> +#define P7_WF6CR (0xE6)
> +#define P7_WF6OBR (0xE8)
> +#define P7_WF7BMR0 (0xEA)
> +#define P7_WF7BMR1 (0xEC)
> +#define P7_WF7CR (0xEE)
> +#define P7_WF7OBR (0xF0)
> +#define P7_WFR01 (0xF2)
> +#define P7_WFR23 (0xF4)
> +#define P7_WFR45 (0xF6)
> +#define P7_WFR67 (0xF8)
> +#define P7_WFPC0 (0xFA)
> +#define P7_WFPC1 (0xFC)
> +
> +/* Tx headers structure */
> +struct tx_sop_header {
> + /* bit 15-11: flags, bit 10-0: packet length */
> + u16 flags_len;
> + /* bit 15-11: sequence number, bit 11-0: packet length bar */
> + u16 seq_lenbar;
> +} __packed;
> +
> +struct tx_segment_header {
> + /* bit 15-14: flags, bit 13-11: segment number */
> + /* bit 10-0: segment length */
> + u16 flags_seqnum_seglen;
> + /* bit 15-14: end offset, bit 13-11: start offset */
> + /* bit 10-0: segment length bar */
> + u16 eo_so_seglenbar;
> +} __packed;
> +
> +struct tx_eop_header {
> + /* bit 15-11: sequence number, bit 10-0: packet length */
> + u16 seq_len;
> + /* bit 15-11: sequence number bar, bit 10-0: packet length bar */
> + u16 seqbar_lenbar;
> +} __packed;
> +
> +struct tx_pkt_info {
> + struct tx_sop_header sop;
> + struct tx_segment_header seg;
> + struct tx_eop_header eop;
> + u16 pkt_len;
> + u16 seq_num;
> +} __packed;
> +
> +/* Rx headers structure */
> +struct rx_header {
> + u16 flags_len;
> + u16 seq_lenbar;
> + u16 flags;
> +} __packed;
> +
> +extern unsigned long ax88796c_no_regs_mask[];
> +
> +#endif /* #ifndef _AX88796C_MAIN_H */
> diff --git a/drivers/net/ethernet/asix/ax88796c_spi.c b/drivers/net/ethernet/asix/ax88796c_spi.c
> new file mode 100644
> index 000000000000..1a20bbeb4dc1
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/ax88796c_spi.c
> @@ -0,0 +1,111 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2010 ASIX Electronics Corporation
> + * Copyright (c) 2020 Samsung Electronics Co., Ltd.
> + *
> + * ASIX AX88796C SPI Fast Ethernet Linux driver
> + */
> +
> +#define pr_fmt(fmt) "ax88796c: " fmt
> +
> +#include <linux/string.h>
> +#include <linux/spi/spi.h>
> +
> +#include "ax88796c_spi.h"
> +
> +/* driver bus management functions */
> +int axspi_wakeup(const struct axspi_data *ax_spi)
> +{
> + u8 tx_buf;
> + int ret;
> +
> + tx_buf = AX_SPICMD_EXIT_PWD; /* OP */
> + ret = spi_write(ax_spi->spi, &tx_buf, 1);
> + if (ret)
> + dev_err(&ax_spi->spi->dev, "%s() failed: ret = %d\n", __func__, ret);
> + return ret;
> +}
> +
> +int axspi_read_status(const struct axspi_data *ax_spi, struct spi_status *status)
> +{
> + u8 tx_buf;
> + int ret;
> +
> + /* OP */
> + tx_buf = AX_SPICMD_READ_STATUS;
> + ret = spi_write_then_read(ax_spi->spi, &tx_buf, 1, (u8 *)&status, 3);
> + if (ret)
> + dev_err(&ax_spi->spi->dev, "%s() failed: ret = %d\n", __func__, ret);
> + else
> + le16_to_cpus(&status->isr);
> +
> + return ret;
> +}
> +
> +int axspi_read_rxq(struct axspi_data *ax_spi, void *data, int len)
> +{
> + struct spi_transfer *xfer = ax_spi->spi_rx_xfer;
> + int ret;
> +
> + memcpy(ax_spi->cmd_buf, rx_cmd_buf, 5);
> +
> + xfer->tx_buf = ax_spi->cmd_buf;
> + xfer->rx_buf = NULL;
> + xfer->len = ax_spi->comp ? 2 : 5;
> + xfer->bits_per_word = 8;
> + spi_message_add_tail(xfer, &ax_spi->rx_msg);
> +
> + xfer++;
> + xfer->rx_buf = data;
> + xfer->tx_buf = NULL;
> + xfer->len = len;
> + xfer->bits_per_word = 8;
> + spi_message_add_tail(xfer, &ax_spi->rx_msg);
> + ret = spi_sync(ax_spi->spi, &ax_spi->rx_msg);
> + if (ret)
> + dev_err(&ax_spi->spi->dev, "%s() failed: ret = %d\n", __func__, ret);
> +
> + return ret;
> +}
> +
> +int axspi_write_txq(const struct axspi_data *ax_spi, void *data, int len)
> +{
> + return spi_write(ax_spi->spi, data, len);
> +}
> +
> +u16 axspi_read_reg(const struct axspi_data *ax_spi, u8 reg)
> +{
> + u8 tx_buf[4];
> + u16 rx_buf = 0;
> + int ret;
> + int len = ax_spi->comp ? 3 : 4;
> +
> + tx_buf[0] = 0x03; /* OP code read register */
> + tx_buf[1] = reg; /* register address */
> + tx_buf[2] = 0xFF; /* dumy cycle */
> + tx_buf[3] = 0xFF; /* dumy cycle */
> + ret = spi_write_then_read(ax_spi->spi, tx_buf, len, (u8 *)&rx_buf, 2);
> + if (ret)
> + dev_err(&ax_spi->spi->dev, "%s() failed: ret = %d\n", __func__, ret);
> + else
> + le16_to_cpus(&rx_buf);
> +
> + return rx_buf;
> +}
> +
> +int axspi_write_reg(const struct axspi_data *ax_spi, u8 reg, u16 value)
> +{
> + u8 tx_buf[4];
> + int ret;
> +
> + tx_buf[0] = AX_SPICMD_WRITE_REG; /* OP code read register */
> + tx_buf[1] = reg; /* register address */
> + tx_buf[2] = value;
> + tx_buf[3] = value >> 8;
> +
> + ret = spi_write(ax_spi->spi, tx_buf, 4);
> + if (ret)
> + dev_err(&ax_spi->spi->dev, "%s() failed: ret = %d\n", __func__, ret);
> + return ret;
> +}
> +
> diff --git a/drivers/net/ethernet/asix/ax88796c_spi.h b/drivers/net/ethernet/asix/ax88796c_spi.h
> new file mode 100644
> index 000000000000..7a49205c2cfb
> --- /dev/null
> +++ b/drivers/net/ethernet/asix/ax88796c_spi.h
> @@ -0,0 +1,69 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * Copyright (c) 2010 ASIX Electronics Corporation
> + * Copyright (c) 2020 Samsung Electronics Co., Ltd.
> + *
> + * ASIX AX88796C SPI Fast Ethernet Linux driver
> + */
> +
> +#ifndef _AX88796C_SPI_H
> +#define _AX88796C_SPI_H
> +
> +#include <linux/spi/spi.h>
> +#include <linux/types.h>
> +
> +/* Definition of SPI command */
> +#define AX_SPICMD_WRITE_TXQ 0x02
> +#define AX_SPICMD_READ_REG 0x03
> +#define AX_SPICMD_READ_STATUS 0x05
> +#define AX_SPICMD_READ_RXQ 0x0B
> +#define AX_SPICMD_BIDIR_WRQ 0xB2
> +#define AX_SPICMD_WRITE_REG 0xD8
> +#define AX_SPICMD_EXIT_PWD 0xAB
> +
> +static const u8 rx_cmd_buf[5] = {AX_SPICMD_READ_RXQ, 0xFF, 0xFF, 0xFF, 0xFF};
> +static const u8 tx_cmd_buf[4] = {AX_SPICMD_WRITE_TXQ, 0xFF, 0xFF, 0xFF};
> +
> +struct axspi_data {
> + struct spi_device *spi;
> + struct spi_message rx_msg;
> + struct spi_transfer spi_rx_xfer[2];
> + u8 cmd_buf[6];
> + u8 comp;
> +};
> +
> +struct spi_status {
> + u16 isr;
> + u8 status;
> +# define AX_STATUS_READY 0x80
> +};
> +
> +int axspi_read_rxq(struct axspi_data *ax_spi, void *data, int len);
> +int axspi_write_txq(const struct axspi_data *ax_spi, void *data, int len);
> +u16 axspi_read_reg(const struct axspi_data *ax_spi, u8 reg);
> +int axspi_write_reg(const struct axspi_data *ax_spi, u8 reg, u16 value);
> +int axspi_read_status(const struct axspi_data *ax_spi, struct spi_status *status);
> +int axspi_wakeup(const struct axspi_data *ax_spi);
> +
> +static inline u16 AX_READ(const struct axspi_data *ax_spi, u8 offset)
> +{
> + return axspi_read_reg(ax_spi, offset);
> +}
> +
> +static inline int AX_WRITE(const struct axspi_data *ax_spi, u16 value, u8 offset)
> +{
> + return axspi_write_reg(ax_spi, offset, value);
> +}
> +
> +static inline int AX_READ_STATUS(const struct axspi_data *ax_spi,
> + struct spi_status *status)
> +{
> + return axspi_read_status(ax_spi, status);
> +}
> +
> +static inline int AX_WAKEUP(struct axspi_data *ax_spi)
> +{
> + return axspi_wakeup(ax_spi);
> +}
> +#endif
> +
>