[PATCH v3 1/2] mmc: sdhci-of-arasan: Enable UHS-1 support for Keem Bay SOC

[muhammad . husaini . zulkifli]

From: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@xxxxxxxxx>

Voltage switching sequence is needed to support UHS-1 interface.
There are 2 places to control the voltage.
1) By setting the AON register using firmware driver calling
system-level platform management layer (SMC) to set the register.
2) By controlling the GPIO expander value to drive either 1.8V or 3.3V
for power mux input.

Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@xxxxxxxxx>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxx>
Reviewed-by: Adrian Hunter <adrian.hunter@xxxxxxxxx>
---
 drivers/mmc/host/sdhci-of-arasan.c | 127 +++++++++++++++++++++++++++++
 1 file changed, 127 insertions(+)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index f186fbd016b1..e681e6f860ba 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -16,6 +16,7 @@
  */
 
 #include <linux/clk-provider.h>
+#include <linux/gpio/consumer.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
@@ -23,6 +24,7 @@
 #include <linux/regmap.h>
 #include <linux/of.h>
 #include <linux/firmware/xlnx-zynqmp.h>
+#include <linux/firmware/intel/keembay_firmware.h>
 
 #include "cqhci.h"
 #include "sdhci-pltfm.h"
@@ -150,6 +152,7 @@ struct sdhci_arasan_data {
 	struct regmap	*soc_ctl_base;
 	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
 	unsigned int	quirks;
+	struct gpio_desc *uhs_gpio;
 
 /* Controller does not have CD wired and will not function normally without */
 #define SDHCI_ARASAN_QUIRK_FORCE_CDTEST	BIT(0)
@@ -361,6 +364,113 @@ static int sdhci_arasan_voltage_switch(struct mmc_host *mmc,
 	return -EINVAL;
 }
 
+static int sdhci_arasan_keembay_voltage_switch(struct mmc_host *mmc,
+				       struct mmc_ios *ios)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	u16 ctrl_2;
+	u16 clk;
+	int ret;
+
+	switch (ios->signal_voltage) {
+	case MMC_SIGNAL_VOLTAGE_180:
+		clk  = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+		clk &= ~SDHCI_CLOCK_CARD_EN;
+		sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+
+		clk  = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+		if (clk & SDHCI_CLOCK_CARD_EN)
+			return -EAGAIN;
+
+		sdhci_writeb(host, SDHCI_POWER_ON | SDHCI_POWER_180,
+				   SDHCI_POWER_CONTROL);
+
+		/*
+		 * Set VDDIO_B voltage to Low for 1.8V
+		 * which is controlling by GPIO Expander.
+		 */
+		gpiod_set_value_cansleep(sdhci_arasan->uhs_gpio, 0);
+
+		/*
+		 * This is like final gatekeeper. Need to ensure changed voltage
+		 * is settled before and after turn on this bit.
+		 */
+		usleep_range(1000, 1100);
+
+		ret = keembay_sd_voltage_selection(KEEMBAY_SET_1V8_VOLT);
+		if (ret)
+			return ret;
+
+		usleep_range(1000, 1100);
+
+		ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+		ctrl_2 |= SDHCI_CTRL_VDD_180;
+		sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+		/* Sleep for 5ms to stabilize 1.8V regulator */
+		usleep_range(5000, 5500);
+
+		/* 1.8V regulator output should be stable within 5 ms */
+		ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+		if (!(ctrl_2 & SDHCI_CTRL_VDD_180))
+			return -EAGAIN;
+
+		clk  = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+		clk |= SDHCI_CLOCK_CARD_EN;
+		sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+		break;
+	case MMC_SIGNAL_VOLTAGE_330:
+		/*
+		 * Set VDDIO_B voltage to High for 3.3V
+		 * which is controlling by GPIO Expander.
+		 */
+		gpiod_set_value_cansleep(sdhci_arasan->uhs_gpio, 1);
+
+		/*
+		 * This is like final gatekeeper. Need to ensure changed voltage
+		 * is settled before and after turn on this bit.
+		 */
+		usleep_range(1000, 1100);
+
+		ret = keembay_sd_voltage_selection(KEEMBAY_SET_3V3_VOLT);
+		if (ret)
+			return ret;
+
+		usleep_range(1000, 1100);
+
+		/* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+		ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+		ctrl_2 &= ~SDHCI_CTRL_VDD_180;
+		sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+		/* Sleep for 5ms to stabilize 3.3V regulator */
+		usleep_range(5000, 5500);
+
+		/* 3.3V regulator output should be stable within 5 ms */
+		ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+		if (ctrl_2 & SDHCI_CTRL_VDD_180)
+			return -EAGAIN;
+
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int sdhci_arasan_keembay_select_drive_strength(struct mmc_card *card,
+					unsigned int max_dtr, int host_drv,
+					int card_drv, int *drv_type)
+{
+	if (card->host->ios.signal_voltage == MMC_SIGNAL_VOLTAGE_180)
+		*drv_type = MMC_SET_DRIVER_TYPE_C;
+
+	return 0;
+}
+
 static const struct sdhci_ops sdhci_arasan_ops = {
 	.set_clock = sdhci_arasan_set_clock,
 	.get_max_clock = sdhci_pltfm_clk_get_max_clock,
@@ -1521,6 +1631,7 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	struct sdhci_pltfm_host *pltfm_host;
 	struct sdhci_arasan_data *sdhci_arasan;
 	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
 	const struct sdhci_arasan_of_data *data;
 
 	match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node);
@@ -1600,6 +1711,22 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 		host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY;
 	}
 
+	if (of_device_is_compatible(np, "intel,keembay-sdhci-5.1-sd")) {
+		struct gpio_desc *uhs;
+
+		uhs = devm_gpiod_get_optional(dev, "uhs", GPIOD_OUT_HIGH);
+		if (IS_ERR(uhs))
+			return dev_err_probe(dev, PTR_ERR(uhs), "can't get uhs gpio\n");
+
+		sdhci_arasan->uhs_gpio = uhs;
+
+		host->mmc_host_ops.start_signal_voltage_switch =
+			sdhci_arasan_keembay_voltage_switch;
+
+		host->mmc_host_ops.select_drive_strength =
+			sdhci_arasan_keembay_select_drive_strength;
+	}
+
 	sdhci_arasan_update_baseclkfreq(host);
 
 	ret = sdhci_arasan_register_sdclk(sdhci_arasan, clk_xin, &pdev->dev);
-- 
2.17.1