[PATCH 1/3] ARM: dts: BCM5301X: Linksys EA9500 make use of pinctrl

[Vivek Unune]

Forgo the use of mmioreg mdio mux infavor of the pinctrl

Signed-off-by: Vivek Unune <npcomplete13@xxxxxxxxx>
---
 .../boot/dts/bcm47094-linksys-panamera.dts    | 153 +++++++++---------
 arch/arm/boot/dts/bcm5301x.dtsi               |   4 +-
 2 files changed, 74 insertions(+), 83 deletions(-)

diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
index 0faae8950375..f8443d9f86b7 100644
--- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -122,87 +122,6 @@ bluebar8 {
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 	};
-
-	mdio-bus-mux {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* BIT(9) = 1 => external mdio */
-		mdio_ext: mdio@200 {
-			reg = <0x200>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
-	mdio-mii-mux {
-		compatible = "mdio-mux-mmioreg";
-		mdio-parent-bus = <&mdio_ext>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x1800c1c0 0x4>;
-
-		/* BIT(6) = mdc, BIT(7) = mdio */
-		mux-mask = <0xc0>;
-
-		mdio-mii@0 {
-			/* Enable MII function */
-			reg = <0x0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			switch@0  {
-				compatible = "brcm,bcm53125";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-				reset-names = "robo_reset";
-				reg = <0>;
-				dsa,member = <1 0>;
-
-				ports {
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					port@0 {
-						reg = <0>;
-						label = "lan1";
-					};
-
-					port@1 {
-						reg = <1>;
-						label = "lan5";
-					};
-
-					port@2 {
-						reg = <2>;
-						label = "lan2";
-					};
-
-					port@3 {
-						reg = <3>;
-						label = "lan6";
-					};
-
-					port@4 {
-						reg = <4>;
-						label = "lan3";
-					};
-
-					sw1_p8: port@8 {
-						reg = <8>;
-						ethernet = <&sw0_p0>;
-						label = "cpu";
-
-						fixed-link {
-							speed = <1000>;
-							full-duplex;
-						};
-					};
-				};
-			};
-		};
-	};
 };
 
 &usb2 {
@@ -265,6 +184,78 @@ fixed-link {
 	};
 };
 
+&pinctrl {
+	compatible = "brcm,bcm4709-pinmux";
+
+	pinmux_mdio: mdio {
+		groups = "mdio_grp";
+		function = "mdio";
+	};
+};
+
+&mdio_bus_mux {
+
+	/* BIT(9) = 1 => external mdio */
+	mdio@200 {
+		reg = <0x200>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@0  {
+			compatible = "brcm,bcm53125";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+			reset-names = "robo_reset";
+			reg = <0>;
+			dsa,member = <1 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_mdio>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan1";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan5";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan6";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan3";
+				};
+
+				sw1_p8: port@8 {
+					reg = <8>;
+					ethernet = <&sw0_p0>;
+					label = "cpu";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+	};
+};
+
 &usb3_phy {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 9d9e8fe3f6ae..1476375f88bb 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -369,7 +369,7 @@ mdio: mdio@18003000 {
 		#address-cells = <1>;
 	};
 
-	mdio-bus-mux@18003000 {
+	mdio_bus_mux: mdio-bus-mux@18003000 {
 		compatible = "mdio-mux-mmioreg";
 		mdio-parent-bus = <&mdio>;
 		#address-cells = <1>;
@@ -428,7 +428,7 @@ cru@100 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			pin-controller@1c0 {
+			pinctrl: pin-controller@1c0 {
 				compatible = "brcm,bcm4708-pinmux";
 				reg = <0x1c0 0x24>;
 				reg-names = "cru_gpio_control";
-- 
2.25.1