Re: [PATCH v2 3/7] media: i2c: max9286: Break-out reverse channel setup

From: Kieran Bingham
Date: Thu Oct 15 2020 - 15:53:30 EST


Hi Jacopo,

On 15/10/2020 19:27, Jacopo Mondi wrote:
> Break out the reverse channel setup configuration procedure to its own
> function.
>
> This change prepares for configuring the reverse channel conditionally
> to the remote side high threshold configuration.
>
> No functional changes intended.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> ---
> drivers/media/i2c/max9286.c | 30 +++++++++++++++++-------------
> 1 file changed, 17 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
> index d969ac21a058..89a7248f5c25 100644
> --- a/drivers/media/i2c/max9286.c
> +++ b/drivers/media/i2c/max9286.c
> @@ -906,6 +906,22 @@ static void max9286_v4l2_unregister(struct max9286_priv *priv)
> * Probe/Remove
> */
>
> +static void max9286_reverse_channel_setup(struct max9286_priv *priv)
> +{
> + /*
> + * Reverse channel setup.
> + *
> + * - Enable custom reverse channel configuration (through register 0x3f)
> + * and set the first pulse length to 35 clock cycles.
> + * - Increase the reverse channel amplitude to 170mV to accommodate the
> + * high threshold enabled by the serializer driver.
> + */
> + max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35));
> + max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) |
> + MAX9286_REV_AMP_X);
> + usleep_range(2000, 2500);
> +}

This gets moved later on in the same series. It's probably better to put
it in the right place now.

With that,

Reviewed-by: Kieran Bingham <kieran.bingham+renesasa@xxxxxxxxxxxxxxxx>

> +
> static int max9286_setup(struct max9286_priv *priv)
> {
> /*
> @@ -941,19 +957,7 @@ static int max9286_setup(struct max9286_priv *priv)
> * only. This should be disabled after the mux is initialised.
> */
> max9286_configure_i2c(priv, true);
> -
> - /*
> - * Reverse channel setup.
> - *
> - * - Enable custom reverse channel configuration (through register 0x3f)
> - * and set the first pulse length to 35 clock cycles.
> - * - Increase the reverse channel amplitude to 170mV to accommodate the
> - * high threshold enabled by the serializer driver.
> - */
> - max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35));
> - max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) |
> - MAX9286_REV_AMP_X);
> - usleep_range(2000, 2500);
> + max9286_reverse_channel_setup(priv);
>
> /*
> * Enable GMSL links, mask unused ones and autodetect link
>