Re: [PATCH v3 4/4] dt-bindings: arm: add support for SCMI Regulators

[Rob Herring]

On Mon, Oct 26, 2020 at 08:31:48PM +0000, Cristian Marussi wrote:
> Add devicetree bindings to support regulators based on SCMI Voltage
> Domain Protocol.
> 
> Signed-off-by: Cristian Marussi <cristian.marussi@xxxxxxx>
> ---
> v2 --> v3
> - avoid awkard examples based on _cpu/_gpu regulators
> v1 --> v2
> - removed any reference to negative voltages
> ---
>  .../devicetree/bindings/arm/arm,scmi.txt      | 42 +++++++++++++++++++
>  1 file changed, 42 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt
> index 55deb68230eb..0cef83a60f03 100644
> --- a/Documentation/devicetree/bindings/arm/arm,scmi.txt
> +++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt
> @@ -62,6 +62,28 @@ Required properties:
>   - #power-domain-cells : Should be 1. Contains the device or the power
>  			 domain ID value used by SCMI commands.
>  
> +Regulator bindings for the SCMI Regulator based on SCMI Message Protocol
> +------------------------------------------------------------
> +
> +An SCMI Regulator is permanently bound to a well defined SCMI Voltage Domain,
> +and should be always positioned as a root regulator.
> +It does not support any current operation.
> +
> +This binding uses the common regulator binding[6].
> +
> +SCMI Regulators are grouped under a 'regulators' node which in turn is a child
> +of the SCMI Voltage protocol node inside the desired SCMI instance node.
> +
> +Required properties:
> + - reg : shall identify an existent SCMI Voltage Domain.
> +
> +Optional properties:
> + - all of the other standard regulator bindings as in [6]: note that, since
> +   the SCMI Protocol itself aims in fact to hide away many of the operational
> +   capabilities usually exposed by the properties of a standard regulator,
> +   most of the usual regulator bindings could have just no effect in the
> +   context of this SCMI regulator.

You can't have it both ways... You should list out which ones apply.

I'm a bit worried that now we're changing CPUs (at least?) from clocks 
to 'performance domains' while at the same time here we're adding 
low level, virtual regulators. Are we going to end up wanting something 
more abstract here too?

> +
>  Sensor bindings for the sensors based on SCMI Message Protocol
>  --------------------------------------------------------------
>  SCMI provides an API to access the various sensors on the SoC.
> @@ -105,6 +127,7 @@ Required sub-node properties:
>  [3] Documentation/devicetree/bindings/thermal/thermal*.yaml
>  [4] Documentation/devicetree/bindings/sram/sram.yaml
>  [5] Documentation/devicetree/bindings/reset/reset.txt
> +[6] Documentation/devicetree/bindings/regulator/regulator.yaml
>  
>  Example:
>  
> @@ -169,6 +192,25 @@ firmware {
>  			reg = <0x16>;
>  			#reset-cells = <1>;
>  		};
> +
> +		scmi_voltage: protocol@17 {
> +			reg = <0x17>;
> +
> +			regulators {
> +				regulator_devX: regulator_scmi_devX@0 {

Node names should be generic:

regulator@0

> +					reg = <0x0>;
> +					regulator-max-microvolt = <3300000>;
> +				};
> +
> +				regulator_devY: regulator_scmi_devY@9 {
> +					reg = <0x9>;
> +					regulator-min-microvolt = <500000>;
> +					regulator-max-microvolt = <4200000>;
> +				};
> +
> +				...
> +			};
> +		};
>  	};
>  };
>  
> -- 
> 2.17.1
>