Re: [PATCH 1/1] iio: adc: stm32-adc: fix a regression when using dma and irq
From: Jonathan Cameron
Date: Sun Nov 01 2020 - 12:15:38 EST
On Wed, 21 Oct 2020 10:53:13 +0200
Olivier Moysan <olivier.moysan@xxxxxx> wrote:
> Since overrun interrupt support has been added, there's a regression when
> two ADCs are used at the same time, with:
> - an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
> called in this case.
> - an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
> request. It's then automatically cleared by DMA read. But the handler
> gets called due to status bit is temporarily set (IRQ triggered by the
> other ADC).
>
> This is a regression as similar issue had been fixed earlier by
> commit dcb10920179a ("iio: adc: stm32-adc:
> fix a race when using several adcs with dma and irq").
> Issue is that stm32_adc_eoc_enabled() returns non-zero value (always)
> since OVR bit has been added and enabled for both DMA and IRQ case.
>
> Remove OVR mask in IER register, and rely only on CSR status for overrun.
> To avoid subsequent calls to interrupt routine on overrun, CSR OVR bit has
> to be cleared. CSR OVR bit cannot be cleared directly by software.
> To do this ADC must be stopped first, and OVR bit in ADC ISR has
> to be cleared.
> Also add a check in ADC IRQ handler to report spurious IRQs.
>
> Fixes: cc06e67d8fa5 ("iio: adc: stm32-adc: Add check on overrun interrupt")
>
> Signed-off-by: Olivier Moysan <olivier.moysan@xxxxxx>
> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@xxxxxx>
Applied to the fixes-togreg branch of iio.git and marked for stable.
Thanks,
Jonathan
> ---
> drivers/iio/adc/stm32-adc-core.c | 41 +++++++++++---------------
> drivers/iio/adc/stm32-adc.c | 50 ++++++++++++++++++++++++++++++--
> 2 files changed, 65 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/iio/adc/stm32-adc-core.c b/drivers/iio/adc/stm32-adc-core.c
> index cd870c089182..a83199b212a4 100644
> --- a/drivers/iio/adc/stm32-adc-core.c
> +++ b/drivers/iio/adc/stm32-adc-core.c
> @@ -41,18 +41,16 @@
> * struct stm32_adc_common_regs - stm32 common registers
> * @csr: common status register offset
> * @ccr: common control register offset
> - * @eoc1_msk: adc1 end of conversion flag in @csr
> - * @eoc2_msk: adc2 end of conversion flag in @csr
> - * @eoc3_msk: adc3 end of conversion flag in @csr
> + * @eoc_msk: array of eoc (end of conversion flag) masks in csr for adc1..n
> + * @ovr_msk: array of ovr (overrun flag) masks in csr for adc1..n
> * @ier: interrupt enable register offset for each adc
> * @eocie_msk: end of conversion interrupt enable mask in @ier
> */
> struct stm32_adc_common_regs {
> u32 csr;
> u32 ccr;
> - u32 eoc1_msk;
> - u32 eoc2_msk;
> - u32 eoc3_msk;
> + u32 eoc_msk[STM32_ADC_MAX_ADCS];
> + u32 ovr_msk[STM32_ADC_MAX_ADCS];
> u32 ier;
> u32 eocie_msk;
> };
> @@ -282,21 +280,20 @@ static int stm32h7_adc_clk_sel(struct platform_device *pdev,
> static const struct stm32_adc_common_regs stm32f4_adc_common_regs = {
> .csr = STM32F4_ADC_CSR,
> .ccr = STM32F4_ADC_CCR,
> - .eoc1_msk = STM32F4_EOC1 | STM32F4_OVR1,
> - .eoc2_msk = STM32F4_EOC2 | STM32F4_OVR2,
> - .eoc3_msk = STM32F4_EOC3 | STM32F4_OVR3,
> + .eoc_msk = { STM32F4_EOC1, STM32F4_EOC2, STM32F4_EOC3},
> + .ovr_msk = { STM32F4_OVR1, STM32F4_OVR2, STM32F4_OVR3},
> .ier = STM32F4_ADC_CR1,
> - .eocie_msk = STM32F4_EOCIE | STM32F4_OVRIE,
> + .eocie_msk = STM32F4_EOCIE,
> };
>
> /* STM32H7 common registers definitions */
> static const struct stm32_adc_common_regs stm32h7_adc_common_regs = {
> .csr = STM32H7_ADC_CSR,
> .ccr = STM32H7_ADC_CCR,
> - .eoc1_msk = STM32H7_EOC_MST | STM32H7_OVR_MST,
> - .eoc2_msk = STM32H7_EOC_SLV | STM32H7_OVR_SLV,
> + .eoc_msk = { STM32H7_EOC_MST, STM32H7_EOC_SLV},
> + .ovr_msk = { STM32H7_OVR_MST, STM32H7_OVR_SLV},
> .ier = STM32H7_ADC_IER,
> - .eocie_msk = STM32H7_EOCIE | STM32H7_OVRIE,
> + .eocie_msk = STM32H7_EOCIE,
> };
>
> static const unsigned int stm32_adc_offset[STM32_ADC_MAX_ADCS] = {
> @@ -318,6 +315,7 @@ static void stm32_adc_irq_handler(struct irq_desc *desc)
> {
> struct stm32_adc_priv *priv = irq_desc_get_handler_data(desc);
> struct irq_chip *chip = irq_desc_get_chip(desc);
> + int i;
> u32 status;
>
> chained_irq_enter(chip, desc);
> @@ -335,17 +333,12 @@ static void stm32_adc_irq_handler(struct irq_desc *desc)
> * before invoking the interrupt handler (e.g. call ISR only for
> * IRQ-enabled ADCs).
> */
> - if (status & priv->cfg->regs->eoc1_msk &&
> - stm32_adc_eoc_enabled(priv, 0))
> - generic_handle_irq(irq_find_mapping(priv->domain, 0));
> -
> - if (status & priv->cfg->regs->eoc2_msk &&
> - stm32_adc_eoc_enabled(priv, 1))
> - generic_handle_irq(irq_find_mapping(priv->domain, 1));
> -
> - if (status & priv->cfg->regs->eoc3_msk &&
> - stm32_adc_eoc_enabled(priv, 2))
> - generic_handle_irq(irq_find_mapping(priv->domain, 2));
> + for (i = 0; i < priv->cfg->num_irqs; i++) {
> + if ((status & priv->cfg->regs->eoc_msk[i] &&
> + stm32_adc_eoc_enabled(priv, i)) ||
> + (status & priv->cfg->regs->ovr_msk[i]))
> + generic_handle_irq(irq_find_mapping(priv->domain, i));
> + }
>
> chained_irq_exit(chip, desc);
> };
> diff --git a/drivers/iio/adc/stm32-adc.c b/drivers/iio/adc/stm32-adc.c
> index b3f31f147347..16c02c30dec7 100644
> --- a/drivers/iio/adc/stm32-adc.c
> +++ b/drivers/iio/adc/stm32-adc.c
> @@ -154,6 +154,7 @@ struct stm32_adc;
> * @start_conv: routine to start conversions
> * @stop_conv: routine to stop conversions
> * @unprepare: optional unprepare routine (disable, power-down)
> + * @irq_clear: routine to clear irqs
> * @smp_cycles: programmable sampling time (ADC clock cycles)
> */
> struct stm32_adc_cfg {
> @@ -166,6 +167,7 @@ struct stm32_adc_cfg {
> void (*start_conv)(struct iio_dev *, bool dma);
> void (*stop_conv)(struct iio_dev *);
> void (*unprepare)(struct iio_dev *);
> + void (*irq_clear)(struct iio_dev *indio_dev, u32 msk);
> const unsigned int *smp_cycles;
> };
>
> @@ -621,6 +623,13 @@ static void stm32f4_adc_stop_conv(struct iio_dev *indio_dev)
> STM32F4_ADON | STM32F4_DMA | STM32F4_DDS);
> }
>
> +static void stm32f4_adc_irq_clear(struct iio_dev *indio_dev, u32 msk)
> +{
> + struct stm32_adc *adc = iio_priv(indio_dev);
> +
> + stm32_adc_clr_bits(adc, adc->cfg->regs->isr_eoc.reg, msk);
> +}
> +
> static void stm32h7_adc_start_conv(struct iio_dev *indio_dev, bool dma)
> {
> struct stm32_adc *adc = iio_priv(indio_dev);
> @@ -659,6 +668,13 @@ static void stm32h7_adc_stop_conv(struct iio_dev *indio_dev)
> stm32_adc_clr_bits(adc, STM32H7_ADC_CFGR, STM32H7_DMNGT_MASK);
> }
>
> +static void stm32h7_adc_irq_clear(struct iio_dev *indio_dev, u32 msk)
> +{
> + struct stm32_adc *adc = iio_priv(indio_dev);
> + /* On STM32H7 IRQs are cleared by writing 1 into ISR register */
> + stm32_adc_set_bits(adc, adc->cfg->regs->isr_eoc.reg, msk);
> +}
> +
> static int stm32h7_adc_exit_pwr_down(struct iio_dev *indio_dev)
> {
> struct stm32_adc *adc = iio_priv(indio_dev);
> @@ -1235,17 +1251,40 @@ static int stm32_adc_read_raw(struct iio_dev *indio_dev,
> }
> }
>
> +static void stm32_adc_irq_clear(struct iio_dev *indio_dev, u32 msk)
> +{
> + struct stm32_adc *adc = iio_priv(indio_dev);
> +
> + adc->cfg->irq_clear(indio_dev, msk);
> +}
> +
> static irqreturn_t stm32_adc_threaded_isr(int irq, void *data)
> {
> struct iio_dev *indio_dev = data;
> struct stm32_adc *adc = iio_priv(indio_dev);
> const struct stm32_adc_regspec *regs = adc->cfg->regs;
> u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg);
> + u32 mask = stm32_adc_readl(adc, regs->ier_eoc.reg);
>
> - if (status & regs->isr_ovr.mask)
> + /* Check ovr status right now, as ovr mask should be already disabled */
> + if (status & regs->isr_ovr.mask) {
> + /*
> + * Clear ovr bit to avoid subsequent calls to IRQ handler.
> + * This requires to stop ADC first. OVR bit state in ISR,
> + * is propaged to CSR register by hardware.
> + */
> + adc->cfg->stop_conv(indio_dev);
> + stm32_adc_irq_clear(indio_dev, regs->isr_ovr.mask);
> dev_err(&indio_dev->dev, "Overrun, stopping: restart needed\n");
> + return IRQ_HANDLED;
> + }
>
> - return IRQ_HANDLED;
> + if (!(status & mask))
> + dev_err_ratelimited(&indio_dev->dev,
> + "Unexpected IRQ: IER=0x%08x, ISR=0x%08x\n",
> + mask, status);
> +
> + return IRQ_NONE;
> }
>
> static irqreturn_t stm32_adc_isr(int irq, void *data)
> @@ -1254,6 +1293,10 @@ static irqreturn_t stm32_adc_isr(int irq, void *data)
> struct stm32_adc *adc = iio_priv(indio_dev);
> const struct stm32_adc_regspec *regs = adc->cfg->regs;
> u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg);
> + u32 mask = stm32_adc_readl(adc, regs->ier_eoc.reg);
> +
> + if (!(status & mask))
> + return IRQ_WAKE_THREAD;
>
> if (status & regs->isr_ovr.mask) {
> /*
> @@ -2046,6 +2089,7 @@ static const struct stm32_adc_cfg stm32f4_adc_cfg = {
> .start_conv = stm32f4_adc_start_conv,
> .stop_conv = stm32f4_adc_stop_conv,
> .smp_cycles = stm32f4_adc_smp_cycles,
> + .irq_clear = stm32f4_adc_irq_clear,
> };
>
> static const struct stm32_adc_cfg stm32h7_adc_cfg = {
> @@ -2057,6 +2101,7 @@ static const struct stm32_adc_cfg stm32h7_adc_cfg = {
> .prepare = stm32h7_adc_prepare,
> .unprepare = stm32h7_adc_unprepare,
> .smp_cycles = stm32h7_adc_smp_cycles,
> + .irq_clear = stm32h7_adc_irq_clear,
> };
>
> static const struct stm32_adc_cfg stm32mp1_adc_cfg = {
> @@ -2069,6 +2114,7 @@ static const struct stm32_adc_cfg stm32mp1_adc_cfg = {
> .prepare = stm32h7_adc_prepare,
> .unprepare = stm32h7_adc_unprepare,
> .smp_cycles = stm32h7_adc_smp_cycles,
> + .irq_clear = stm32h7_adc_irq_clear,
> };
>
> static const struct of_device_id stm32_adc_of_match[] = {