Re: [PATCH -next] irq-chip/gic-v3-its: Fixed an issue where the ITS executes the residual commands in the queue again when the ITS wakes up from sleep mode.

[Marc Zyngier]

[dropping Jason, whose email address has been bouncing for weeks now]

On 2020-11-07 10:42, Xu Qiang wrote:
> On my platform, ITS_FLAGS_SAVE_SUSPEND_STATE is not set,thus do nothing

Which platform?

> in its suspend and resuse function.On the other hand,firmware stores
> GITS_CTRL,GITS_CBASER,GITS_CWRITER and GITS_BASER<n> in the suspend,
> and restores these registers in the resume. As a result, the ITS 
> executes
> the residual commands in the queue.

Which firmware are you using? I just had a look at the trusted firmware 
source
code, and while it definitely does something that *looks* like what you 
are
describing, it doesn't re-enable the ITS on resume.

So what are you running?

> Memory corruption may occur in the following scenarios:
>
> The kernel sends three commands in the following sequence:
> 1.mapd(deviceA, ITT_addr1, valid:1)
> 2.mapti(deviceA):ITS write ITT_addr1 memory;
> 3.mapd(deviceA, ITT_addr1, valid:0) and kfree(ITT_addr1);

The ITS doesn't 'kfree' stuff.

> 4.mapd(deviceA, ITT_addr2, valid:1);
> 5.mapti(deviceA):ITS write ITT_addr2 memory;

I don't think this example is relevant. The core of the problem is that
the ITS gets re-enabled by your firmware. What are the affected systems?

> To solve this problem,dropping the checks for 
> ITS_FLAGS_SAVE_SUSPEND_STATE.
>
> Signed-off-by: Xu Qiang <xuqiang36@xxxxxxxxxx>
> ---
>  drivers/irqchip/irq-gic-v3-its.c | 13 -------------
>  1 file changed, 13 deletions(-)
>
> diff --git a/drivers/irqchip/irq-gic-v3-its.c 
> b/drivers/irqchip/irq-gic-v3-its.c
> index 0fec31931e11..06f2c1c252b9 100644
> --- a/drivers/irqchip/irq-gic-v3-its.c
> +++ b/drivers/irqchip/irq-gic-v3-its.c
> @@ -42,7 +42,6 @@
>  #define ITS_FLAGS_CMDQ_NEEDS_FLUSHING		(1ULL << 0)
>  #define ITS_FLAGS_WORKAROUND_CAVIUM_22375	(1ULL << 1)
>  #define ITS_FLAGS_WORKAROUND_CAVIUM_23144	(1ULL << 2)
> -#define ITS_FLAGS_SAVE_SUSPEND_STATE		(1ULL << 3)
>
>  #define RDIST_FLAGS_PROPBASE_NEEDS_FLUSHING	(1 << 0)
>  #define RDIST_FLAGS_RD_TABLES_PREALLOCATED	(1 << 1)
> @@ -4741,9 +4740,6 @@ static int its_save_disable(void)
>  	list_for_each_entry(its, &its_nodes, entry) {
>  		void __iomem *base;
>
> -		if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
> -			continue;
> -
>  		base = its->base;
>  		its->ctlr_save = readl_relaxed(base + GITS_CTLR);
>  		err = its_force_quiescent(base);
> @@ -4762,9 +4758,6 @@ static int its_save_disable(void)
>  		list_for_each_entry_continue_reverse(its, &its_nodes, entry) {
>  			void __iomem *base;
>
> -			if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
> -				continue;
> -
>  			base = its->base;
>  			writel_relaxed(its->ctlr_save, base + GITS_CTLR);
>  		}
> @@ -4784,9 +4777,6 @@ static void its_restore_enable(void)
>  		void __iomem *base;
>  		int i;
>
> -		if (!(its->flags & ITS_FLAGS_SAVE_SUSPEND_STATE))
> -			continue;
> -
>  		base = its->base;
>
>  		/*
> @@ -5074,9 +5064,6 @@ static int __init its_probe_one(struct resource 
> *res,
>  		ctlr |= GITS_CTLR_ImDe;
>  	writel_relaxed(ctlr, its->base + GITS_CTLR);
>
> -	if (GITS_TYPER_HCC(typer))
> -		its->flags |= ITS_FLAGS_SAVE_SUSPEND_STATE;
> -
>  	err = its_init_domain(handle, its);
>  	if (err)
>  		goto out_free_tables;

I'm OK with the patch itself, but I don't want to paper over broken 
firmware.
I'll get TF-A fixed one way or another, but I want to be sure yours is 
too.
If firmware does its job correctly, we shouldn't have to do all of this.

        M.
--
Jazz is not dead. It just smells funny...