[PATCH] ARM: dts: r8a7742-iwg21d-q7-dbcm-ca: Add OV7725 nodes

[Lad Prabhakar]

Add the ov7725 endpoint nodes to the camera daughter board. The ov7725
sensors can be populated on I2C{0,1,2,3} buses.

By default the VIN{0,1,2,3} are tied to OV5640{0,1,2,3} endpoints
respectively in the camera DB dts hence the remote-endpoint property in
OV7725{0,1,2,3} endpoints is commented out.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
---
Hi All,

This patch is based on top of [1].

[1] https://git.kernel.org/pub/scm/linux/kernel/git/geert/
    renesas-devel.git/log/?h=renesas-arm-dt-for-v5.11

Cheers,
Prabhakar
---
 .../boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts    | 93 +++++++++++++++++++
 1 file changed, 93 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
index 98c3fbd89fa6..d1386bf7bdbe 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
@@ -108,6 +108,29 @@
 			};
 		};
 	};
+
+	ov7725@21 {
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		clocks = <&mclk_cam1>;
+
+		port {
+			ov7725_0: endpoint {
+				bus-width = <8>;
+				bus-type = <6>;
+				/*
+				 * uncomment remote-endpoint property to
+				 * tie ov7725_0 to vin0ep also make
+				 * sure to comment/remove remote-endpoint
+				 * property from ov5640_0 endpoint and
+				 * replace remote-endpoint property in
+				 * vin0ep node with
+				 * remote-endpoint = <&ov7725_0>;
+				 */
+				/* remote-endpoint = <&vin0ep>; */
+			};
+		};
+	};
 };
 
 &i2c1 {
@@ -133,6 +156,29 @@
 			};
 		};
 	};
+
+	ov7725@21 {
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		clocks = <&mclk_cam2>;
+
+		port {
+			ov7725_1: endpoint {
+				bus-width = <8>;
+				bus-type = <6>;
+				/*
+				 * uncomment remote-endpoint property to
+				 * tie ov7725_1 to vin1ep also make
+				 * sure to comment/remove remote-endpoint
+				 * property from ov5640_1 endpoint and
+				 * replace remote-endpoint property in
+				 * vin1ep node with
+				 * remote-endpoint = <&ov7725_1>;
+				 */
+				/* remote-endpoint = <&vin1ep>; */
+			};
+		};
+	};
 };
 
 &i2c2 {
@@ -152,6 +198,30 @@
 			};
 		};
 	};
+
+	ov7725@21 {
+		status = "disabled";
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		clocks = <&mclk_cam3>;
+
+		port {
+			ov7725_2: endpoint {
+				bus-width = <8>;
+				bus-type = <6>;
+				/*
+				 * uncomment remote-endpoint property to
+				 * tie ov7725_2 to vin2ep also make
+				 * sure to comment/remove remote-endpoint
+				 * property from ov5640_2 endpoint and
+				 * replace remote-endpoint property in
+				 * vin2ep node with
+				 * remote-endpoint = <&ov7725_2>;
+				 */
+				/* remote-endpoint = <&vin2ep>; */
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -177,6 +247,29 @@
 			};
 		};
 	};
+
+	ov7725@21 {
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		clocks = <&mclk_cam4>;
+
+		port {
+			ov7725_3: endpoint {
+				bus-width = <8>;
+				bus-type = <6>;
+				/*
+				 * uncomment remote-endpoint property to
+				 * tie ov7725_3 to vin3ep also make
+				 * sure to comment/remove remote-endpoint
+				 * property from ov5640_3 endpoint and
+				 * replace remote-endpoint property in
+				 * vin3ep node with
+				 * remote-endpoint = <&ov7725_3>;
+				 */
+				/* remote-endpoint = <&vin3ep>; */
+			};
+		};
+	};
 };
 
 &pfc {
-- 
2.17.1